ASTM D6875-2008 923 Standard Test Method for Solidification Point of Industrial Organic Chemicals by Thermistor《用热敏电阻测定工业用有机化学品凝固点的标准试验方法》.pdf
《ASTM D6875-2008 923 Standard Test Method for Solidification Point of Industrial Organic Chemicals by Thermistor《用热敏电阻测定工业用有机化学品凝固点的标准试验方法》.pdf》由会员分享,可在线阅读,更多相关《ASTM D6875-2008 923 Standard Test Method for Solidification Point of Industrial Organic Chemicals by Thermistor《用热敏电阻测定工业用有机化学品凝固点的标准试验方法》.pdf(4页珍藏版)》请在麦多课文档分享上搜索。
1、Designation: D 6875 08Standard Test Method forSolidification Point of Industrial Organic Chemicals byThermistor1This standard is issued under the fixed designation D 6875; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of
2、 last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This test method covers a general procedure for deter-mining the solidification point of most organic chemicalshaving
3、 appreciable heats of fusion and solidification pointsbetween 4 and 41C.NOTE 1Other test methods for determining freeze point and solidifi-cation point of aromatic hydrocarbons include Test Methods D 852,D 1015, D 1016, D 3799, D 4493, and D 6269.1.2 This test method is applicable to relatively pure
4、 com-pounds only. Solidification point depression is dependent onimpurity concentrations.1.3 The following applies to all specified limits in this testmethod: for purposes of determining conformance with appli-cable specifications using this test method, an observed valueor a calculated value shall
5、be rounded off “to the nearest unit”in the last right hand digit used in expressing the specificationlimit, in accordance with the “rounding-off method” of PracticeE29.1.4 The values stated in SI units are to be regarded asstandard. No other units of measurement are included in thisstandard.1.5 This
6、 standard does not purport to address all of thesafety concerns, if any, associated with its use. It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use. For a specifichazard s
7、tatement, see Section 8, Hazards.2. Referenced Documents2.1 ASTM Standards:2D 852 Test Method for Solidification Point of BenzeneD 1015 Test Method for Freezing Points of High-PurityHydrocarbonsD 1016 Test Method for Purity of Hydrocarbons fromFreezing PointsD 3437 Practice for Sampling and Handling
8、 Liquid CyclicProductsD 3438 Practice for Sampling and Handling Naphthalene,Maleic Anhydride, and Phthalic AnhydrideD 3799 Test Method for purity of Styrene by Freezing PointMethod3D 3852 Practice for Sampling and Handling Phenol,Cresols, and Cresylic AcidD 4297 Practice for Sampling and Handling Bi
9、sphenol A(4,48 -Isopropylidinediphenol)D 4493 Test Method for Solidification Point of Bisphenol A(4,48-Isopropylidenediphenol)D 6269 Test Method for Solidification Point of p-Xylene3E29 Practice for Using Significant Digits in Test Data toDetermine Conformance with Specifications2.2 Other Documents:
10、OSHA Regulations, 29 CFR paragraphs 1910.1000 and1910.120043. Terminology3.1 Definitions:3.1.1 solidification point, nan empirical constant definedas the temperature at which the liquid phase of a substance isin approximate equilibrium with a relatively small portion ofthe solid phase.3.1.1.1 Discus
11、sionSolidification point as distinguishedfrom freezing point is described in Test Method D 1015.Aninterpretation of mole percent in terms of freezing point isgiven in Test Method D 1016.1This test method is under the jurisdiction of ASTM Committee D16 onAromatic Hydrocarbons and Related Chemicals an
12、d is the direct responsibility ofSubcommittee D16.04 on Instrumental Analysis.Current edition approved Oct. 1, 2008. Published November 2008. Originallyapproved in 2003. Last previous edition approved in 2003 as D 6875 - 03.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcont
13、act ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.3Withdrawn.4Available from U.S. Government Printing Office Superintendent of Documents,732 N. Capitol St., NW, Mail Stop: SDE, Washington
14、, DC 20401, http:/www.access.gpo.gov.1Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.4. Summary of Test Method4.1 The solidification point is measured by noting themaximum temperature reached during a cooling cycle after theappearanc
15、e of a solid phase.5. Significance and Use5.1 This test method may be used for process control duringthe manufacture of organic chemicals described in Section 1,for setting specifications, for development and research work,and to determine if contamination was introduced duringshipment.6. Apparatus6
16、.1 Ohmmeter, capable of measuring resistance to the near-est 0.1 ohm in the range of 1000 to 10 000 ohms with directtemperature readout.56.2 Specimen Container, thick walled test tube with 18 mmoutside diameter and 14 mm inside diameter and 150 mm long.6.3 Stirrer, consisting of a 1-mm stainless ste
17、el wire bentinto a circular form at right angles to the shaft so it will movefreely in the annular space between the thermistor and the wallof the test tube.6.4 Stirring Apparatus (Optional)The apparatus illus-trated in Fig. 1 has been demonstrated to be an acceptablereplacement for manual stirring.
18、6.5 Temperature Bath, capable of being controlled at 5 61C below the expected solidification point.6.6 Thermistor, in stainless steel housing with resistancegreater than 2K ohms at 25C. Calibration accuracy 60.01C.Drift in resistance equivalent to less than 60.01C/year.Thermistor shall be calibrated
19、 to cover the range it is used.67. Reagents and Materials7.1 Cooling Media:7.1.1 Water is recommended for solidification points be-tween 4 and 30C.7.2 Drying Agents:7.2.1 3A Molecular Sieve, in the form of a powder orcylindrical granules about 3 mm in diameter.8. Hazards8.1 Consult current OSHA regu
20、lations, suppliers MaterialSafety Data Sheets, and local regulations for all materials usedin this procedure.8.2 Appropriate personal protection equipment such asgloves, safety glasses, a long rubber apron, and a full faceshield should be worn when handling hot or corrosive chemi-cals, or both.8.3 A
21、 fume hood should be used when performing the testmethod on hazardous chemicals (OSHA 1910.1450 definition).9. Sampling and Handling9.1 Sample the material in accordance with PracticesD 3437, D 3438, D 3852, and D 4297.10. Preparation of Apparatus10.1 Fit the sample container with a two-hole stopper
22、.Through one hole insert the thermistor. Through the other holeinsert the shaft of the stirrer. (See Fig. 1).10.2 Set temperature bath at 5 6 1C. below the expectedsolidification point of the sample.11. Calibration of Thermistor11.1 Thermistor should be calibrated by the factory at aminimum every tw
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
5000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ASTMD68752008923STANDARDTESTMETHODFORSOLIDIFICATIONPOINTOFINDUSTRIALORGANICCHEMICALSBYTHERMISTOR 热敏电阻
链接地址:http://www.mydoc123.com/p-523834.html