ASTM D5905-1998(2003) Standard Practice for the Preparation of Substitute Wastewater《代用品废水准备的标准操作规程》.pdf

《ASTM D5905-1998(2003) Standard Practice for the Preparation of Substitute Wastewater《代用品废水准备的标准操作规程》.pdf》由会员分享，可在线阅读，更多相关《ASTM D5905-1998(2003) Standard Practice for the Preparation of Substitute Wastewater《代用品废水准备的标准操作规程》.pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: D 5905 98 (Reapproved 2003)Standard Practice forthe Preparation of Substitute Wastewater1This standard is issued under the fixed designation D 5905; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of last revi

2、sion. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon (e) indicates an editorial change since the last revision or reapproval.1. Scope1.1 This practice covers the preparation of an aqueousmixture containing constituents in concentrations such that itwill have phys

3、ical and chemical matrix characteristics similarto municipal wastewater.1.2 Wastewaters are extremely variable, depending on thequantity and nature of the materials being discharged into thecollection system. The mixture prepared with this practice isnot representative of any particular wastewater.

4、Rather, itallows the user to prepare a mixture that exhibits a similarmatrix impact on test method performance as is typical ofmunicipal wastewater and can be prepared from commonmaterials inexpensively and reproducibly. It allows the evalu-ation of test methods, over time, against the same referenc

5、epoint.1.3 This standard does not purport to address all of thesafety concerns, if any, associated with its use. It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2. Refer

6、enced Documents2.1 ASTM Standards:2D 1129 Terminology Relating to WaterD 1141 Specification for Substitute Ocean WaterD 1193 Specification for Reagent WaterD 2777 Practice for Determination of Precision and Bias ofApplicable Methods of Committee D19 on Water3. Terminology3.1 DefinitionsFor definitio

7、ns of terms used in this prac-tice, refer to Terminology D 1129.3.2 Definitions of Terms Specific to This Standard:3.2.1 substitute wastewatera mixture of dissolved andsuspended materials in water, typical of the influent to amunicipal wastewater treatment facility.4. Significance and Use4.1 Substit

8、ute wastewater may be used for laboratory testingwhere a reproducible mixture simulating municipal wastewateris required. To provide a more rugged evaluation of a testmethods ability to measure analytes and the precision of thetest method under more demanding conditions, it is necessaryto utilize a

9、matrix more complex than reagent water. Substitutewastewater is intended to be used as a material to be spikedwith analytes or interferents of interest to evaluate the perfor-mance of test methods.4.2 Utilization of substitute wastewater as a matrix ininterlaboratory validation studies will allow in

10、clusion of per-formance statistics for this matrix in the Precision and Biassection of test methods. Users of test methods will be able toevaluate their application of test methods in this matrix againstpublished results.5. Apparatus5.1 Blender, household or commercial variety, with achemically iner

11、t container and a tight sealing lid.6. Reagents6.1 Purity of ReagentsReagent grade chemicals shall beused in all tests. Unless otherwise indicated, it is intended thatall reagents conform to the specifications of the Committee onAnalytical Reagents of the American Chemical Society wheresuch specific

12、ations are available.3Other grades may be used,provided it is first ascertained that the reagent is of sufficientlyhigh purity to permit its use without lessening the accuracy ofdetermination.6.2 Purity of WaterUnless otherwise indicated, referencesto water shall be understood to mean reagent water

13、as definedby Type I of Specification D 1193.6.3 KaolinUSP grade. Dry to constant weight at 103Cbefore use.1This practice is under the jurisdiction of ASTM Committee D19 on Water andis the direct responsibility of Subcommittee D19.02 on General Specifications,Technical Resources, and Statistical Meth

14、ods.Current edition approved Aug. 10, 2003. Published November 2003. Originallypublished as D 590596. Last previous edition D 590598.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume infor

15、mation, refer to the standards Document Summary page onthe ASTM website.3Reagent Chemicals, American Chemical Society Specifications, AmericanChemical Society, Washington, DC. For suggestions on the testing of reagents notlisted by the American Chemical Society, see Analar Standards for LaboratoryCh

16、emicals, BDH Ltd., Poole, Dorset, U.K., and the United States Pharmacopeiaand National Formulary, U.S. Pharmaceutical Convention, Inc. (USPC), Rockville,MD.1Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.6.4 BeerA commercially produc

17、ed beverage made byfermenting mixtures of grains, malts, and hops; reducedcalorie: less than 100 calories/12 oz (1180 J/mL). Reduced-calorie beers are often sold with the designation “lite” or“light.” Transfer the beer into a container and then cap,allowing 20 % head space. Shake vigorously. Loosen

18、cap.Allow to sit refrigerated for 24 h to dissipate carbonation andthen allow to reach room temperature.6.5 FlourGeneral or all-purpose, bleached, enriched, pre-sifted, wheat. All brands fitting this description are acceptable.Dry to constant weight at 103C before use.6.6 Ocean Salts, Commercially a

19、vailable as dry salt mix-tures used to prepare water for salt water aquariums. Can bepurchased at pet stores. Dry to constant weight at 103C beforeuse.6.7 Triton X-1004SolutionSurfactant solution.Add 1.200g to water and dilute to 1 L.NOTE 1A key purpose of this practice is to provide a reproduciblef

20、ormulation. The use of an alternate surfactant may significantly alter theperformance of this material in its intended application. Use of analternate surfactant should be clearly indicated whenever data related tothe use of this practice is published.7. Procedure7.1 Place approximately 500 mL of wa

21、ter in blender.7.2 Add the following amounts of the indicated reagents:7.2.1 Flour, 0.400 g,7.2.2 Ocean salts, 2.000 g,7.2.3 Kaolin, 0.080 g,7.2.4 Triton X-100 solution, 20.0 mL, and7.2.5 Beer, 120.0 mL.7.3 Blend on lowest setting for 30 s. Significant foam willbe generated. Allow most of the foam t

22、o subside beforetransferring. Transfer quantitatively to a 2-L volumetric flaskand dilute to 2 L with water.7.4 This solution may be held at 0 to 4C for up to 24 h butthen shall be preserved and held per the requirements of the testmethod under evaluation.8. Keywords8.1 analytical performance; matri

23、x; wastewaterAPPENDIX(Nonmandatory Information)X1. TYPICAL ASSAY RESULTS OF SUBSTITUTE WASTEWATERX1.1 The following analytical results (see Table X1.1) wereobtained in a single laboratory from a single determination.This data is presented for informational purposes only and theuser of this practice

24、should make their own determination ofbackground concentrations.X1.2 All results are in milligrams per litre.4Union Carbide, Triton X-100 has been found to be satisfactory for this purpose.D 5905 98 (2003)2ASTM International takes no position respecting the validity of any patent rights asserted in

25、connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the res

26、ponsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive caref

27、ul consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International

28、, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the AS

29、TM website(www.astm.org).TABLE X1.1 Typical Assay Results of Substitute WastewaterAnalyte Concentration Analyte ConcentrationBiological oxygen demand 570 Selenium 0.002Silver 0.0002 Tin 0.8Aluminum 0.03 Thallium 0.001Arsenic 0.001 Vanadium 0.2Boron 0.1 Mercury 0.0002Barium 0.003 Ammonia nitrogen 0.1

30、Beryllium 0.0002 Kjeldahl nitrogen 30Calcium 10 Phosphorus 8Cobalt 0.05 Nitrite nitrogen 0.01Iron 0.1 Nitrate nitrogen 0.05Potassium 26 Suspended solids 232Copper 0.01 Volatile suspended solids 198Nickel 0.003 Total solids 2200Lead 0.001 Total volatile solids 1300Cadmium 0.001 Chloride 490Chromium 0

31、.001 Chemical oxygen demand 3500Zinc 0.02 Cyanide 0.02Magnesium 33 Ortho phosphorous 7Manganese 0.01 Sulfate 85Molybdenum 0.03 Total organic carbon 1600Sodium 200 USEPA Priority Pollutant List organic compounds all below detectionAAntimony 0.003AThe Priority Pollutant List as found in Title 40, Code

32、 of Federal Regulations, Part 122, Appendix D, Table II (40 CFR, Part 122) by the U.S. Environmental ProtectionAgency, 1990. Gas Chromatography and Gas Chromatography/Mass Spectroscopy Methods 624, 625, and 608 as found in Title 40, Code of Federal Regulations, Part136, Appendix A, (40 CFR, Part 136) by the U.S. Environmental Protection Agency, 1990. Samples diluted 1:4 for determination of volatile components due to foaming.D 5905 98 (2003)3