ASTM D5319-2017 Standard Specification for Glass-Fiber Reinforced Polyester Wall and Ceiling Panels《玻璃纤维增强聚酯墙板和天花板的标准规格》.pdf
《ASTM D5319-2017 Standard Specification for Glass-Fiber Reinforced Polyester Wall and Ceiling Panels《玻璃纤维增强聚酯墙板和天花板的标准规格》.pdf》由会员分享,可在线阅读,更多相关《ASTM D5319-2017 Standard Specification for Glass-Fiber Reinforced Polyester Wall and Ceiling Panels《玻璃纤维增强聚酯墙板和天花板的标准规格》.pdf(5页珍藏版)》请在麦多课文档分享上搜索。
1、Designation: D5319 12D5319 17 An American National StandardStandard Specification forGlass-Fiber Reinforced Polyester Wall and Ceiling Panels1This standard is issued under the fixed designation D5319; the number immediately following the designation indicates the year oforiginal adoption or, in the
2、case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope*1.1 This specification covers the classification, materials of construction, workmanship, p
3、hysical requirements, and methods oftesting glass-fiber-reinforced polyester composite wall and ceiling panels intended for use in light construction and semi-structuralapplications.1.2 Supplementary information on chemical resistance, impact resistance, and installation practice are provided in App
4、endixX1.1.3 The classification of these composite panels into classes based on relative response to a laboratory test shall not beconsidered a fire-hazard classification.1.4 Laboratory flammability tests (Test Methods E84 and D1929) applicable to this specification should be used to measure anddescr
5、ibe the properties of materials, products, or assemblies in response to heat and flame under controlled laboratory conditionsand should not be used to describe or appraise the fire hazard or conditions. However, results may be used as elements of a firerisk assessment which takes into account all of
6、 the factors which are pertinent to an assessment of the fire hazard of a particularend use.1.5 The intent of this specification is to define the class, grade, and general laminate properties of the composite wall and ceilingliner panels in order to ensure a quality product which will perform in the
7、 intended application. This specification is not intendedto restrict or limit technological changes affecting performance when changes are agreed upon between the purchaser andmanufacturer.1.6 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses a
8、re provided forinformation only.1.7 The text of this specification references notes and footnotes that provide explanatory material. These notes and footnotes(excluding those in Tables and Figures) shall not be considered as requirements of this specification.1.8 This standard does not purport to ad
9、dress all of the safety concerns, if any, associated with its use. It is the responsibilityof the user of this standard to establish appropriate safety safety, health and healthenvironmental practices and determine theapplicability of regulatory limitations prior to use.NOTE 1There is no known ISO e
10、quivalent to this standard.NOTE 1There is no known ISO equivalent to this standard.1.9 This international standard was developed in accordance with internationally recognized principles on standardizationestablished in the Decision on Principles for the Development of International Standards, Guides
11、 and Recommendations issuedby the World Trade Organization Technical Barriers to Trade (TBT) Committee.2. Referenced Documents2.1 ASTM Standards:2D374D374/D374M Test Methods for Thickness of Solid Electrical Insulation (Metric) D0374_D0374MD618 Practice for Conditioning Plastics for TestingD883 Term
12、inology Relating to PlasticsD1600 Terminology for Abbreviated Terms Relating to Plastics1 This specification is under the jurisdiction of ASTM Committee D20 on Plastics and is the direct responsibility of Subcommittee D20.24 on Plastic Building Products.Current edition approved Oct. 1, 2012Sept. 1,
13、2017. Published November 2012September 2017. Originally approved in 1992. Last previous edition approved in 20082012as D5319 97(2008).12. DOI: 10.1520/D5319-12.10.1520/D5319-17.2 For referencedASTM standards, visit theASTM website, www.astm.org, or contactASTM Customer Service at serviceastm.org. Fo
14、r Annual Book of ASTM Standardsvolume information, refer to the standards Document Summary page on the ASTM website.This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Becauseit may n
15、ot be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current versionof the standard as published by ASTM is to be considered the official document.*A Summary of Changes section appears at the e
16、nd of this standardCopyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States1D1929 Test Method for Determining Ignition Temperature of PlasticsD2244 Practice for Calculation of Color Tolerances and Color Differences from Instrumentally Measured
17、 Color CoordinatesD3029 Test Methods for Impact Resistance of Flat, Rigid Plastic Specimens by Means of a Tup (Falling Weight) (Withdrawn1995)3E84 Test Method for Surface Burning Characteristics of Building MaterialsE631 Terminology of Building Constructions3. Terminology3.1 GeneralDefinitions are i
18、n accordance with Terminologies D883 and E631 and abbreviations with Terminology D1600,unless otherwise indicated.3.2 Definitions of Terms Specific to This Standard:3.2.1 camber, nnon-linearity of the long axis of a panel.NOTE 2In the process of water jet, knife, saw, or rotary shear trimming of a c
19、ontinuous panel, sidewards motion of the panel through the cuttingmedium can be induced by imbalances in the system. The resulting trim cuts, although maintaining parallelism between the long sides, may describe acontinuous curve, rather than a straight line along the long axis of the panel. Imbalan
20、ces in side-to-side cure rates or material distribution may also producethis phenomenon. This curvature of the long axis may create problems with installation of the panel. Limits are placed on the degree of non-linearity tominimize those problems.4. Classification4.1 The panels covered by this spec
21、ification are divided into four classifications based on relative response to the laboratoryflammability of Test Method E84.4.1.1 Class AFlame spread index 0 to 25, smoke development index of 450 or less.4.1.2 Class BFlame spread index 26 to 75, smoke development index of 450 or less.4.1.3 Class CFl
22、ame spread index 76 to 200, smoke development index of 450 or less.4.1.4 Class DGeneral purpose, no flame spread or smoke development indices.NOTE 3Refer to 1.3 on flammability testing and fire hazard classification.4.2 These classifications may be further subdivided into grades based on nominal thi
23、ckness when tested in accordance with 8.4:4.2.1 Grade 10.027 to 0.033 in. (0.69 to 0.84 mm); 0.030 in. nominal (0.76 mm).4.2.2 Grade 20.036 to 0.044 in. (0.91 to 1.12 mm); 0.040 in. nominal (1.02 mm).4.2.3 Grade 30.040 to 0.050 in. (1.02 to 1.27 mm); 0.045 in. nominal (1.14 mm).4.2.4 Grade 40.054 to
24、 0.066 in. (1.37 to 1.68 mm); 0.060 in. nominal (1.52 mm).4.2.5 Grade 50.067 to 0.083 in. (1.70 to 2.11 mm); 0.075 in. nominal (1.91 mm).4.2.6 Grade 60.081 to 0.099 in. (2.06 to 2.51 mm); 0.090 in. nominal (2.29 mm).4.2.7 Grade 70.108 to 0.132 in. (2.74 to 3.35 mm); 0.120 in. nominal (3.05 mm).4.3 W
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ASTMD53192017STANDARDSPECIFICATIONFORGLASSFIBERREINFORCEDPOLYESTERWALLANDCEILINGPANELS 玻璃纤维 增强 聚酯 天花板

链接地址:http://www.mydoc123.com/p-519465.html