ASTM C1606-2004 Standard Test Method for Sampling Protocol for TCLP Testing of Container Glassware《瓶罐玻璃器皿的TCLP检验用取样协议的标准试验方法》.pdf

《ASTM C1606-2004 Standard Test Method for Sampling Protocol for TCLP Testing of Container Glassware《瓶罐玻璃器皿的TCLP检验用取样协议的标准试验方法》.pdf》由会员分享，可在线阅读，更多相关《ASTM C1606-2004 Standard Test Method for Sampling Protocol for TCLP Testing of Container Glassware《瓶罐玻璃器皿的TCLP检验用取样协议的标准试验方法》.pdf（2页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: C 1606 04Standard Test Method forSampling Protocol for TCLP Testing of ContainerGlassware1This standard is issued under the fixed designation C 1606; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of last rev

2、ision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon (e) indicates an editorial change since the last revision or reapproval.1. Scope1.1 This test method defines the way in which containerglassware should be prepared before performing the ToxicityCharacteristic

3、Leaching Procedure (TCLP). The method coversthe homogenization of the sample, and the selection of arepresentative portion of the sample to test and get reproduc-ible results.1.2 This standard does not purport to address all of thesafety concerns, if any, associated with its use. It is theresponsibi

4、lity of the user of this standard to establish appro-priate safety and health practices and to determine theapplicability of regulatory limitations prior to use.2. Referenced Documents2.1 ASTM Standards:2E 691 Practice for Conducting an Interlaboratory Study toDetermine the Precision of a Test Metho

5、d3. Summary of Test Method3.1 Container glass articles decorated with ceramic glassdecorations are broken to fit the requirements of the TCLPprotocol by using a disc mill or roll mill apparatus, and then thesamples are homogenized using a riffle box. A representativesample of the glass articles can

6、then be put through the TCLPtest with reproducible results.4. Significance and Use4.1 Sampling of decorated glass containers for the TCLPcan vary greatly, resulting from the size and shape of the articlerelative to the amount of ceramic decoration on the ware.Breaking the glass can cause some of the

7、 pieces to have nodecoration on them, and others to be heavily decorated andmore likely to leach lead and cadmium under the TCLP test.This method provides an effective tool to homogenize the glasscontainers so that reproducible results can be attained from theTCLP test.5. Apparatus5.1 Pre-breaking a

8、pparatus, consisting of:5.1.1 Two L (or larger) polythene bucket with a tightlysealed lid,5.1.2 One or two clean 35 to 40 mm diameter aluminagrinding balls,5.2 Disc mill or roll mill,5.3 Sieves, as needed,5.4 Riffle box, and,5.5 Roller or tumbler apparatus.6. Reagents and Materials6.1 Glassware to b

9、e tested, in two sets of 10 units each.7. Hazards7.1 When working with glassware, always be aware andcareful of the potential of getting cut by the glass. Personalprotective equipment, such as a face shield or goggles, leathergloves, and a protective apron should be worn when workingwith glass.Take

10、precautions when working with the samples andapparatus to avoid the possibilities of getting hurt.8. Sampling, Test Specimens, and Test Units8.1 Since the amount of lead and cadmium that leaches froma decoration can be affected by the relative size of thedecoration, it is important to start with two

11、 sets of ten unitseach.9. Procedure9.1 To minimize the variation of sampling, this testing shallbe done in duplicate, and therefore, take two sets of 10 units ofthe glassware to be tested.9.2 Pre-break the glass prior to milling, using the followingprocedure:1This test method is under the jurisdicti

12、on of ASTM Committee C21 on ceramicWhitewares and Related Products and is the direct responsibility of SubcommitteeC21.03 on Methods for Whitewares and Enviromental Concerns.Current edition approved Nov. 1, 2004. Published November 2004.2For referenced ASTM standards, visit the ASTM website, www.ast

13、m.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.1Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.9.2.1 Pla

14、ce the first set of glassware into the 2 L bucket,along with one or two clean 35 to 40 mm diameter aluminagrinding balls.9.2.2 After tightly sealing the lid, shake the vessel hardenough to smash the glass to create pieces that can be fed intothe roll or disc mill.9.3 Clean both the mill and riffle b

15、ox, prior to use.9.4 Feed the pre-broken glass into the disc mill or roll millas feedstock.9.4.1 Grind the glass as two separate lots, with the selectedmill apertures set between 2.5 mm and 3.5 mm. Theseaperature settings tend to produce crushed glass with a maxi-mum particle size of 5 mm.9.5 Any ov

16、ersized material must be removed by sieving orhand picking, and be broken up prior to blending back into theoriginal sample.9.6 Homogenize the sample using a roller or tumblerapparatus.9.7 Immediately pass sample through the riffle box collect-ing two sub-samples of 100g each.9.8 Perform TCLP extrac

17、tion according to EPA specifica-tions.10. Precision and Bias10.1 The number of laboratories, materials, and determina-tions in this study DOES NOT meet the minimum require-ments for determining precision prescribed in PracticeE 691.10.1.1 This precision statement is provisional. Within fiveyears, ad

18、ditional data will be obtained and processed whichdoes meet the requirements of E 691.11. Keywords11.1 TCLP; ceramic glass enamels; ceramic glassdecorationsASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard

19、. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed

20、every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible te

21、chnical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshoh

22、ocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org).TABLE 1 Precision Statement for Test Method Sampling Protocolfor TCLP Testing of Container GlasswareNOTEPrecision, characterized by repeatability , Sr, r, and reproduc-ibility, SR, R has been determined for the materials to be:Material Average Sr r SR Rppm Pb 0.192000 0.076158 0.213242 0.086429 0.242002C1606042