ASTM B508-2016 Standard Specification for Copper Alloy Strip for Flexible Metal Hose《柔性金属软管用铜合金带材的标准规格》.pdf
《ASTM B508-2016 Standard Specification for Copper Alloy Strip for Flexible Metal Hose《柔性金属软管用铜合金带材的标准规格》.pdf》由会员分享,可在线阅读,更多相关《ASTM B508-2016 Standard Specification for Copper Alloy Strip for Flexible Metal Hose《柔性金属软管用铜合金带材的标准规格》.pdf(9页珍藏版)》请在麦多课文档分享上搜索。
1、Designation: B508 08B508 16Standard Specification forCopper Alloy Strip for Flexible Metal Hose1This standard is issued under the fixed designation B508; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of last revision. A
2、number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the U.S. Department of Defense.1. Scope*1.1 This specification establishes the requirements
3、for annealed copper-alloy strip for the manufacture of flexible metal hoseproduced from Copper Alloy UNS Nos. C41100 and C50500.1.1.1 The nominal compositions are as follows:Copper AlloyUNS No.Copper Zinc TinC41100 91.0 8.5 0.5C50500 98.7 . 1.31.2 The values stated in inch-pound units are to be rega
4、rded as standard. The values given in parentheses are mathematicalconversions to SI units that are provided for information only and are not considered standard. Grain size is given in SI units.1.3 The following precautionary statement pertains only to the test method portion, Section 13, of this sp
5、ecification:Thisstandard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the userof this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations priorto use.2. Referen
6、ced Documents2.1 ASTM Standards:2B601 Classification for Temper Designations for Copper and Copper AlloysWrought and CastB846 Terminology for Copper and Copper AlloysE29 Practice for Using Significant Digits in Test Data to Determine Conformance with SpecificationsE62 Test Methods for Chemical Analy
7、sis of Copper and Copper Alloys (Photometric Methods) (Withdrawn 2010)3E112 Test Methods for Determining Average Grain SizeE255 Practice for Sampling Copper and Copper Alloys for the Determination of Chemical CompositionE478 Test Methods for Chemical Analysis of Copper Alloys3. Terminology3.1 Defini
8、tions:3.1.1 For definitions of terms related to copper and copper alloys, refer to Terminology B846.4. Ordering Information4.1 Orders Include the following choices when placing orders for product under this specification should include the followinginformation:specification, as applicable:4.1.1 ASTM
9、 designation and year of issue,4.1.2 Copper Alloy UNS No.designation (see Section 1 and Table 1),4.1.3 Temper (see 7.1 and Table 2),4.1.4 Quantity, number of pieces or total weight of each alloy and size, and1 This specification is under the jurisdiction of ASTM Committee B05 on Copper and Copper Al
10、loys and is direct responsibility of Subcommittee B05.01 on Plate, Sheet,and Strip.Current edition approved April 1, 2008April 1, 2016. Published April 2008June 2016. Originally approved in 1969. Last previous edition approved in 20072008 asB508 07.B508 08. DOI: 10.1520/B0508-08.10.1520/B0508-16.2 F
11、or referencedASTM standards, visit theASTM website, www.astm.org, or contactASTM Customer Service at serviceastm.org. For Annual Book of ASTM Standardsvolume information, refer to the standards Document Summary page on the ASTM website.3 The last approved version of this historical standard is refer
12、enced on www.astm.org.This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Becauseit may not be technically possible to adequately depict all changes accurately, ASTM recommends that u
13、sers consult prior editions as appropriate. In all cases only the current versionof the standard as published by ASTM is to be considered the official document.*A Summary of Changes section appears at the end of this standardCopyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Cons
14、hohocken, PA 19428-2959. United States14.1.5 DimensionsThickness and width; and length, if applicable (see 8.2 and 8.3).4.1.6 How furnishedCoils (inside and outside diameters), pounds per inch of width; stock or specific lengths, with or withoutends;4.1.7 PackingType of pallet, skid, or box: interle
15、aving, banding, maximum weight, and so forth;4.2 The following options are available and should be but may not be included unless specified at the time of placing of theorder,order when required:4.2.1 How furnishedCoils (inside and outside diameters), pounds per inch of width; stock or specific leng
16、ths, with or withoutends;Heat identification and traceability details;4.2.2 PackingType of pallet, skid, or box: interleaving, banding, maximum weight, and so forth; andCertification;4.2.3 Mill Test Report;4.2.4 Special surface condition requirements, if any (see 9.3).5. Materials and Manufacture5.1
17、 Material:5.1.1 The material of manufacture shall be cast bar, slab, cake, billet, or so forth of Copper Alloy UNS No. C41100 or C50500of such purity and soundness as to be suitable for processing in to into the products prescribed herein.5.1.2 In the event When specified in the contract or purchase
18、 order, that heat identification or traceability is required, thepurchaser shall specify the details desired.NOTE 1Because of the discontinuous nature of the processing of castings into wrought products, it is not always practical to identify specific castinganalysis with a specific quantity of fini
19、shed material.TABLE 1 Chemical RequirementsElementComposition, %Copper Alloy UNS Nos.C41100 C50500Copper 89.092.0 RemainderCopper 89.092.0 remainderTin 0.300.7 1.01.7Phosphorus . 0.030.35Iron, max 0.05 0.10Lead, max 0.09 0.05Zinc remainder 0.30 maxB508 1625.2 Manufacture:5.2.1 The product shall be m
20、anufactured by such hot working, cold working, hot-working, cold-working, and annealingprocesses as to produce a uniform wrought structure in the finished product.5.2.2 The product shall be hothot- or cold worked cold-worked to the finished size and subsequently annealed, if required, tomeet the tem
21、per properties specified.5.2.3 EdgesSlit edges shall be furnished unless otherwise specified in the contract or purchase order.6. Chemical Composition6.1 The material shall conform to the chemical composition requirements prescribed in Table 1 for the alloy specified in theordering information.6.2 T
22、hese composition limits do not preclude the presence of other elements. Limits for unnamed elements By agreementbetween the manufacturer and purchaser, limits may be established and analysis required by agreement between the manufactureror supplier and purchaser.for unnamed elements.6.3 Zinc, when g
23、iven as the “remainder,” is the differences between the sum of the results for all elements analyzedFor alloysin which zinc is listed as “remainder,” either copper or zinc may be taken as the difference of all other elements determined and100 %.6.3.1 Copper may be taken as the difference between the
24、 sum of all elements analyzed and 100 % and, when so determined,the difference value shall conform to the requirements given in Table 1.6.4 When analyzed, the sum of results for all elements listed in Table 1 are determined, the sum of results for Copper AlloyUNS C41100 shall be 99.7 % minimum and 9
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ASTMB5082016STANDARDSPECIFICATIONFORCOPPERALLOYSTRIPFORFLEXIBLEMETALHOSE 柔性 金属软管 铜合金 标准 规格 PDF
链接地址:http://www.mydoc123.com/p-461438.html