ASME PDS-1 1-2013 Dimensioning Tolerancing Surface Texture and Metrology Standards Rules for Drawings With Incomplete Reference to Applicable Drawing Standard《尺寸标注 公差 表面纹理 以及计量学标准 .pdf

《ASME PDS-1 1-2013 Dimensioning Tolerancing Surface Texture and Metrology Standards Rules for Drawings With Incomplete Reference to Applicable Drawing Standard《尺寸标注 公差 表面纹理 以及计量学标准 .pdf》由会员分享，可在线阅读，更多相关《ASME PDS-1 1-2013 Dimensioning Tolerancing Surface Texture and Metrology Standards Rules for Drawings With Incomplete Reference to Applicable Drawing Standard《尺寸标注 公差 表面纹理 以及计量学标准 .pdf（16页珍藏版）》请在麦多课文档分享上搜索。

1、AN AMERICAN NATIONAL STANDARD ASME PDS-1.12013Dimensioning, Tolerancing, Surface Texture, and Metrology Standards Rules for Drawings With Incomplete Reference to Applicable Drawing StandardProduct Definition Specifications (PDS)ASME PDS-1.12013Dimensioning, Tolerancing,Surface Texture, andMetrology

2、Standards Rules for Drawings WithIncomplete Referenceto ApplicableDrawing StandardProduct Definition Specifications (PDS)AN AMERICAN NATIONAL STANDARDTwo Park Avenue New York, NY 10016 USADate of Issuance: December 31, 2013This Standard will be revised when the Society approves the issuance of a new

3、 edition.ASME issues written replies to inquiries concerning interpretations of technical aspects of thisStandard. Periodically certain actions of the ASME Y14 Committee may be published as Cases.Cases and interpretations are published on the ASME Web site under the Committee Pages athttp:/cstools.a

4、sme.org/ as they are issued.Errata to codes and standards may be posted on the ASME Web site under the Committee Pages toprovide corrections to incorrectly published items, or to correct typographical or grammatical errorsin codes and standards. Such errata shall be used on the date posted.The Commi

5、ttee Pages can be found at http:/cstools.asme.org/. There is an option available toautomatically receive an e-mail notification when errata are posted to a particular code or standard.This option can be found on the appropriate Committee Page after selecting “Errata” in the “PublicationInformation”

6、section.ASME is the registered trademark of The American Society of Mechanical Engineers.This code or standard was developed under procedures accredited as meeting the criteria for American NationalStandards. The Standards Committee that approved the code or standard was balanced to assure that indi

7、viduals fromcompetent and concerned interests have had an opportunity to participate. The proposed code or standard was madeavailable for public review and comment that provides an opportunity for additional public input from industry, academia,regulatory agencies, and the public-at-large.ASME does

8、not “approve,” “rate,” or “endorse” any item, construction, proprietary device, or activity.ASME does not take any position with respect to the validity of any patent rights asserted in connection with anyitems mentioned in this document, and does not undertake to insure anyone utilizing a standard

9、against liability forinfringement of any applicable letters patent, nor assumes any such liability. Users of a code or standard are expresslyadvised that determination of the validity of any such patent rights, and the risk of infringement of such rights, isentirely their own responsibility.Particip

10、ation by federal agency representative(s) or person(s) affiliated with industry is not to be interpreted asgovernment or industry endorsement of this code or standard.ASME accepts responsibility for only those interpretations of this document issued in accordance with the establishedASME procedures

11、and policies, which precludes the issuance of interpretations by individuals.No part of this document may be reproduced in any form,in an electronic retrieval system or otherwise,without the prior written permission of the publisher.The American Society of Mechanical EngineersTwo Park Avenue, New Yo

12、rk, NY 10016-5990Copyright 2013 byTHE AMERICAN SOCIETY OF MECHANICAL ENGINEERSAll rights reservedPrinted in U.S.A.CONTENTSForeword ivCommittee Roster . vCorrespondence With the H213 Committee . vii1 Scope 12 Product Definition Specifications. 13 Y14.5 Reference to Standard. 14 Drawings Without Refer

13、ence to a Standard . 15 ANSI/ASME B46 and B89 Standards 1Table1 Editions of ASME Y14, ASME B46.1, and ASME B89 Documents for DrawingsWithout Reference to a Standard . 2iiiFOREWORDEngineering drawings often function as contract documents. This Standard addresses thesituation where no standards are li

14、sted on an engineering drawing; this may cause contract orlegal issues.When an engineering drawing is produced, regardless of the country it was produced in, itmust be based on a set of standards or it is not interpretable. ASME recommends that everydrawing should have its applicable standards state

15、d on the drawing, in a document referencedonthedrawing,orincontractuallyimposeddocuments.The standardsmaybecompany,regional,national, or international standards.Where the applicable engineering drawing standards, surface texture standards, or measure-ment standards are not indicated by one of these

16、methods, the interpretation of the engineeringdrawing and the measurement methods are unspecified. Unfortunately, there are many drawingsin industry that do not have any indication as to which standards are to be used for interpretation.The purpose of this Standard is to identify the set of engineer

17、ing drawing, surface texture,and measurement standards as de facto standards to apply to engineering drawings where nostandards areindicated onthe drawing,in adocument referencedon thedrawing, orin contractu-ally imposed documents.ASMEhasthreecommitteesthatproducestandardsthataffectdrawingspecificat

18、ion,interpreta-tion, and measurement practices. They are as follows:(a) B46 Committee on Classification and Designation of Surface Qualities(b) B89 Committee on Dimensional Metrology(c) Y14 Committee on Engineering Drawing and Related Documentation PracticesThese three ASME Standards Committees have

19、 jointly prepared and individually approvedthis Standard to define the applicable dimensioning and tolerancing standards, surface texturestandards, and associated measurement standards when no reference is made to a company,regional, national, or international standard on dimensioning and tolerancin

20、g on an engineeringdrawing or model. The Special Committee H213 on Harmonization of Dimensional andGeometrical Product Specifications and Verification was instrumental in initiating this document.This Standard was approved as an American National Standard on December 20, 2013.ivSPECIAL COMMITTEE H21

21、3Harmonization of Dimensional and GeometricalProduct Specifications and Verification(The following is the roster of the Committee at the time of approval of this Standard.)STANDARDS COMMITTEE OFFICERSA. Krulikowski, ChairT. Charlton, Jr., Vice ChairS. Weinman, SecretarySTANDARDS COMMITTEE PERSONNELA

22、. R. Anderson, Dimensional Dynamics, LLCF. Bakos, Jr., ConsultantC. A. Brown, Worcester Polytechnic InstituteT. Charlton, Jr., Charlton AssociatesA. Krulikowski, Effective Training, Inc.S. Ledger, Carl Zeiss IMTB46 COMMITTEE CLASSIFICATION AND DESIGNATION OF SURFACE QUALITIESC. A. Brown, Chair, Worc

23、ester Polytechnic InstituteT. B. Renegar, Vice Chair, National Institute of Standards andTechnologyR. Lucas, Secretary, The American Society of Mechanical EngineersE. P. Becker, Friction Order Department: 22 Law Drive, P.O. Box 2900, Fairfield, NJ 07007-2900.NOTES:(1) The ASME B89.7.3.1 standard is

24、invoked only if a drawing, created in 2001 or later, includes decision rule terminology and no refer-ence is made to other explanatory information.(2) The ASME B89.7.5 document is invoked only if a drawing, created in 2006 or later, specifies metrological traceability terminology andno reference is

25、made to other explanatory information.2ASME ServicesASME is committed to developing and delivering technical information. At ASMEs Customer Care, we make every effort to answer your questionsand expedite your orders. Our representatives are ready to assist you in the following areas:ASME Press Membe

26、r Services & Benefits Public InformationCodes & Standards Other ASME Programs Self-Study CoursesCredit Card Orders Payment Inquiries Shipping InformationIMechE Publications Professional Development Subscriptions/Journals/MagazinesMeetings & Conferences Short Courses Symposia VolumesMember Dues Statu

27、s Publications Technical PapersHow can you reach us? Its easier than ever!There are four options for making inquiries* or placing orders. Simply mail, phone, fax, or E-mail us and a Customer Care representative willhandle your request.Mail Call Toll Free Fax24 hours E-Mail24 hoursASME US & Canada: 8

28、00-THE-ASME 973-882-1717 customercareasme.org22 Law Drive, Box 2900 (800-843-2763) 973-882-5155Fairfield, New Jersey Mexico: 95-800-THE-ASME07007-2900 (95-800-843-2763)Universal: 973-882-1167* Customer Care staff are not permitted to answer inquiries about the technical content of this code or stand

29、ard. Information as to whetheror not technical inquiries are issued to this code or standard is shown on the copyright page. All technical inquiries must be submitted inwriting to the staff secretary. Additional procedures for inquiries may be listed within.INTENTIONALLY LEFT BLANKASME PDS-1.12013N19313