ASME B18 6 9-2010 Wing Nuts (Inch Series)《蝶型螺母(英寸系列)》.pdf

《ASME B18 6 9-2010 Wing Nuts (Inch Series)《蝶型螺母(英寸系列)》.pdf》由会员分享，可在线阅读，更多相关《ASME B18 6 9-2010 Wing Nuts (Inch Series)《蝶型螺母(英寸系列)》.pdf（24页珍藏版）》请在麦多课文档分享上搜索。

1、AN AMERICAN NATIONAL STANDARDASME B18.6.9-2010Wing Nuts (Inch Series)INTENTIONALLY LEFT BLANKASME B18.6.9-2010Wing Nuts(Inch Series)AN AMERICAN NATIONAL STANDARDDate of Issuance: March 31, 2010This Standard will be revised when the Society approves the issuance of a new edition. There willbe no adde

2、nda issued to this edition.ASME issues written replies to inquiries concerning interpretations of technical aspects of thisStandard. Periodically certain actions of the ASME B18 Committee may be published as Cases.Cases and interpretations are published on the ASME Web site under the Committee Pages

3、 athttp:/cstools.asme.org as they are issued.ASME is the registered trademark of The American Society of Mechanical Engineers.This code or standard was developed under procedures accredited as meeting the criteria for American NationalStandards. The Standards Committee that approved the code or stan

4、dard was balanced to assure that individuals fromcompetent and concerned interests have had an opportunity to participate. The proposed code or standard was madeavailable for public review and comment that provides an opportunity for additional public input from industry, academia,regulatory agencie

5、s, and the public-at-large.ASME does not “approve,” “rate,” or “endorse” any item, construction, proprietary device, or activity.ASME does not take any position with respect to the validity of any patent rights asserted in connection with anyitems mentioned in this document, and does not undertake t

6、o insure anyone utilizing a standard against liability forinfringement of any applicable letters patent, nor assumes any such liability. Users of a code or standard are expresslyadvised that determination of the validity of any such patent rights, and the risk of infringement of such rights, isentir

7、ely their own responsibility.Participation by federal agency representative(s) or person(s) affiliated with industry is not to be interpreted asgovernment or industry endorsement of this code or standard.ASME accepts responsibility for only those interpretations of this document issued in accordance

8、 with the establishedASME procedures and policies, which precludes the issuance of interpretations by individuals.No part of this document may be reproduced in any form,in an electronic retrieval system or otherwise,without the prior written permission of the publisher.The American Society of Mechan

9、ical EngineersThree Park Avenue, New York, NY 10016-5990Copyright 2010 byTHE AMERICAN SOCIETY OF MECHANICAL ENGINEERSAll rights reservedPrinted in U.S.A.CONTENTSForeword ivCommittee Roster . vCorrespondence With the B18 Committee vi1 Introduction 12 General Data 1Tables1 Dimensions of Type A Wing Nu

10、ts 32 Dimensions of Type B, Style 1 Wing Nuts 43 Dimensions of Type B, Style 2 Wing Nuts 54 Dimensions of Type C, Style 1 Wing Nuts 65 Dimensions of Type C, Style 2 Wing Nuts 76 Dimensions of Type C, Style 3 Wing Nuts 87 Dimensions of Type D, Style 1 Wing Nuts 98 Dimensions of Type D, Style 2 Wing N

11、uts (Low Wing) 109 Dimensions of Type D, Style 3 Wing Nuts (Large Base) . 11iiiFOREWORDThis Standard replaces ASME B18.17, Wing Nuts, Thumb Screws, and Wing Screws, whichwas originally published in 1968 and reaffirmed in 1983. ASME B18 Subcommittee 6 undertooka complete rewrite in 2004 that was conc

12、luded in 2009. ASME B18.17 has been withdrawn, andASME B18.6.9 is now the only inch series Standard for wing nuts.This Standard was approved by the American National Standards Institute on February 3, 2010.ivASME B18 COMMITTEEStandardization of Bolts, Nuts, Rivets, Screws,Washers, and Similar Fasten

13、ers(The following is the roster of the Committee at the time of approval of this Standard.)STANDARDS COMMITTEE OFFICERSJ. Greenslade, ChairD. S. George, Vice ChairR. D. Strong, Vice ChairC. J. Gomez, SecretarySTANDARDS COMMITTEE PERSONNELV. Cartina, Autocraft IndustrialD. A. Clever, ConsultantA. P.

14、Cockman, Ford Motor Co.C. A. Dugal, Texas Screw ProductsD. S. George, ND IndustriesC. J. Gomez, The American Society of Mechanical EngineersJ. Greenslade, Industrial Fasteners InstituteJ. J. Grey, Contributing Member, Fastener Consulting Services, Inc.B. Hasiuk, Contributing Member, Defense Supply C

15、enterPhiladelphiaA. Herskovitz, ConsultantJ. Hubbard, Leland-Powell Fasteners, Inc.J. Jennings, Contributing Member, Naval Surface Warfare CenterW. H. King, Porteous Fasteners Co.J. F. Koehl, Contributing Member, Spirol International Corp.SUBCOMMITTEE6SLOTTEDANDRECESSEDHEAD SCREWSR. D. Strong, Chair

16、, ConsultantJ. Hubbard, Vice Chair, Leland-Powell Fasteners, Inc.G. M. Simpson, Vice Chair, Semblex Corp.A. L. Guzman, Secretary, The American Society of MechanicalEngineersD. A. Clever, ConsultantM. A. Elmi, CaterpillarJ. S. Foote, Trade Association Management, Inc.D. S. George, ND IndustriesJ. Gre

17、enslade, Industrial Fasteners InstituteA. Herskovitz, ConsultantM. W. Holubecki, Electric Boat Corp.vW. H. Kopke, ConsultantW. J. Lutkus, Emhart TeknologiesD. A. McCrindle, Canadian Fasteners InstituteM. D. Prasad, Contributing Member, GlobalM however, they shouldnot contain proprietary names or inf

18、ormation.Requests that are not in this format may be rewritten in the appropriate format by the Committeeprior to being answered, which may inadvertently change the intent of the original request.ASME procedures provide for reconsideration of any interpretation when or if additionalinformation that

19、might affect an interpretation is available. Further, persons aggrieved by aninterpretation may appeal to the cognizant ASME Committee or Subcommittee. ASME does not“approve,” “certify,” “rate,” or “endorse” any item, construction, proprietary device, or activity.Attending Committee Meetings. The B1

20、8 Standards Committee regularly holds meetings thatare open to the public. Persons wishing to attend any meeting should contact the Secretary ofthe B18 Standards Committee.viASME B18.6.9-2010WING NUTS (INCH SERIES)1 INTRODUCTION1.1 ScopeThis Standard covers complete general and dimen-sional data for

21、 nine various types and styles of wingnuts. Thumb screws and wing screws, recognized asAmerican National Standard, are included inASME B18.6.8.The inclusion of dimensional data in this Standard isnot intended to imply that all the products describedare stock production sizes. Purchasers should consu

22、ltwith suppliers concerning availability of products.1.2 Comparison With ISO StandardsThere are no ISO standards at this time.1.3 DimensionsAll dimensions are in inch units. When specifyingnormal sizes, decimal zeros in the fourth place shall beomitted.1.4 TerminologyFor definitions of terms, other

23、than those definedbelow, relating to fasteners or components thereof usedin this Standard, see ASME B18.12.wing nuts: a nut having wings designed for manual turn-ing without driver or wrench. The wing nuts coveredby this Standard are classified, first, by type, on the basisof the method of manufactu

24、re; and second, by style, onthe basis of design characteristics. They consist of thefollowing:Type A: cold forged or cold formed solid nuts havingwings of moderate height. In some sizes, they are pro-duced in regular, light, and heavy series to best suit therequirements of specific applications. Dim

25、ensions aregiven in Table 1.Type B: hot forged solid nuts available in two wingstyles: Style 1, having wings of moderate height; andStyle 2, having high wings. Dimensions are given inTable 2 and Table 3, respectively.Type C: die cast solid nuts and are available in threewing styles: Style 1, having

26、wings of moderate height;Style 2, having low wings; and Style 3, having highwings. In some sizes, the Style 1 nuts are produced inregular and heavy series to best suit the requirementsof specific applications. Dimensions are given in Tables4, 5, and 6 for the respective styles.Type D: stamped sheet

27、metal nuts and are availablein three styles: Style 1, having wings of moderate height;Style 2, having low wings; and Style 3, having wings of1moderate height and a larger bearing surface. In somesizes, Style 2 and Style 3 nuts are produced in regular,light, and heavy series to best suit the requirem

28、ents ofspecific applications. Dimensions are given in Tables 7,8, and 9 for the respective styles.1.5 Referenced DocumentsASME B1.1, Unified Inch Screw Threads (UN and UNRThread Form)ASME B1.3, Screw Thread Gaging Systems forDimensional Acceptability Inch and Metric ScrewThreads (UN, UNR, UNJ, M, an

29、d MJ)ASME B18.12, Glossary of Terms for MechanicalFastenersASME B18.18.2, Inspection and Quality Assurance forHigh-Volume Machine Assembly FastenersPublisher: The American Society of MechanicalEngineers (ASME), Three Park Avenue, New York,NY 10016-5990; Order Department: 22 Law Drive, P.O.Box 2900,

30、Fairfield, NJ 07007 (www.asme.org)2 GENERAL DATA2.1 DesignExcept for bearing surfaces, the details of contour shallbe optional with the manufacturer, provided the speci-fied overall dimensions are maintained.2.2 Bearing SurfaceThe bearing surface of all types of wing nuts shall beat right angles to

31、the axis of the threaded hole within atolerance of 3 deg. The bearing surface shall be free fromburrs, fins, and protruding surface irregularities.2.3 OptionsOptions, where specified, shall be at the discretion ofthe manufacturer, unless otherwise agreed upon by themanufacturer and the user.2.4 Thre

32、adsThreads shall be in conformance with ASME B1.1,Class 2B, for all types of wing nuts except Type D, whichshall be Class 2B with a modified minor diameter.Because of the method of manufacture, the minor diame-ter of the thread in Type D nuts may be larger than theClass 2B maximum size, but in no ca

33、se shall the minordiameter exceed the minimum pitch diameter size.Thread acceptability shall be determined usingASME B1.3, System 21.ASME B18.6.9-20102.5 MaterialThe materials applicable to the various wing nut typesshall be as specified in the following paragraphs.2.5.1 Types A, B, and D. Types A,

34、B, and D wingnuts shall be supplied in carbon steel, brass aluminum,or other materials as agreed upon by the supplier andpurchaser.2.5.2 Type C. Type C wing nuts shall be made froma die cast zinc alloy such as UNS designation Z33520,Z35531, Z35541, or an alloy having similar properties.2.6 FinishUnl

35、ess otherwise specified, wing nuts shall be sup-plied with a plain (unplated or uncoated) finish.22.7 DesignationWhen specifying wing nuts, the following data shallbe included in the description:(a) standard type(b) thread size(c) style and/or series(d) material(e) finishEXAMPLES:(1) ASME B18.6.9, 1

36、0-32 Type A Wing Nut, Heavy Series, Steelper UNS G10060, Zinc Plated to ASTM F 1941, Fe/Zn 3A.(2) ASME B18.6.9,14-20 Type C Wing Nut, Style 1, Zinc Alloy perUNS Z33520, Plain.2.8 Inspection and Quality AssuranceUnless otherwise specified, acceptability of nuts shallbe determined in accordance with A

37、SME B18.18.2.ASME B18.6.9-2010Table 1 Dimensions of Type A Wing NutsEBGDACWing Wing Wing Between Boss BossNominal Size or NutSpread, A Height, B Thickness, C Wings, D Diameter, E Height, GBasic Major Dia. Threads Series Blankof Thread per Inch Note (1) Size (Ref) Max. Min. Max. Min. Max. Min. Max. M

38、in. Max. Min. Max. Min.3 (0.0990) 48 and 56 Heavy AA 0.72 0.59 0.41 0.28 0.11 0.07 0.21 0.17 0.33 0.29 0.14 0.104 (0.1120) 40 and 48 Heavy AA 0.72 0.59 0.41 0.28 0.11 0.07 0.21 0.17 0.33 0.29 0.14 0.105 (0.1250) 40 and 44 Light AA 0.72 0.59 0.41 0.28 0.11 0.07 0.21 0.17 0.33 0.29 0.14 0.105 (0.1250)

39、 40 and 44 Heavy A 0.91 0.78 0.47 0.34 0.14 0.10 0.27 0.22 0.43 0.39 0.18 0.146 (0.1380) 32 and 40 Light AA 0.72 0.59 0.41 0.28 0.11 0.07 0.21 0.17 0.33 0.29 0.14 0.106 (0.1380) 32 and 40 Heavy A 0.91 0.78 0.47 0.34 0.14 0.10 0.27 0.22 0.43 0.39 0.18 0.148 (0.1640) 32 and 36 Light A 0.91 0.78 0.47 0

40、.34 0.14 0.10 0.27 0.22 0.43 0.39 0.18 0.148 (0.1640) 32 and 36 Heavy B 1.10 0.97 0.57 0.43 0.18 0.14 0.33 0.26 0.50 0.45 0.22 0.1710 (0.1900) 24 and 32 Light A 0.91 0.78 0.47 0.34 0.14 0.10 0.27 0.22 0.43 0.39 0.18 0.1410 (0.1900) 24 and 32 Heavy B 1.10 0.97 0.57 0.43 0.18 0.14 0.33 0.26 0.50 0.45

41、0.22 0.1712 (0.2160) 24 and 28 Light B 1.10 0.97 0.57 0.43 0.18 0.14 0.33 0.26 0.50 0.45 0.22 0.1712 (0.2160) 24 and 28 Heavy C 1.25 1.12 0.66 0.53 0.21 0.17 0.39 0.32 0.58 0.51 0.25 0.2014(0.2500) 20 and 28 Light B 1.10 0.97 0.57 0.43 0.18 0.14 0.33 0.26 0.50 0.45 0.22 0.1714(0.2500) 20 and 28 Regu

42、lar C 1.25 1.12 0.66 0.53 0.21 0.17 0.39 0.32 0.58 0.51 0.25 0.2014(0.2500) 20 and 28 Heavy D 1.44 1.31 0.79 0.65 0.24 0.20 0.48 0.42 0.70 0.64 0.30 0.26516(0.3125) 18 and 24 Light C 1.25 1.12 0.66 0.53 0.21 0.17 0.39 0.32 0.58 0.51 0.25 0.20516(0.3125) 18 and 24 Regular D 1.44 1.31 0.79 0.65 0.24 0

43、.20 0.48 0.42 0.70 0.64 0.30 0.26516(0.3125) 18 and 24 Heavy E 1.94 1.81 1.00 0.87 0.33 0.26 0.65 0.54 0.93 0.86 0.39 0.3538(0.3750) 16 and 24 Light D 1.44 1.31 0.79 0.65 0.24 0.20 0.48 0.42 0.70 0.64 0.30 0.2638(0.3750) 16 and 24 Regular E 1.94 1.81 1.00 0.87 0.33 0.26 0.65 0.54 0.93 0.86 0.39 0.35

44、716(0.4375) 14 and 20 Light E 1.94 1.81 1.00 0.87 0.33 0.26 0.65 0.54 0.93 0.86 0.39 0.35716(0.4375) 14 and 20 Heavy F 2.76 2.62 1.44 1.31 0.40 0.34 0.90 0.80 1.19 1.13 0.55 0.5112(0.5000) 13 and 20 Light E 1.94 1.81 1.00 0.87 0.33 0.26 0.65 0.54 0.93 0.86 0.39 0.3512(0.5000) 13 and 20 Heavy F 2.76

45、2.62 1.44 1.31 0.40 0.34 0.90 0.80 1.19 1.13 0.55 0.51916(0.5625) 12 and 18 Heavy F 2.76 2.62 1.44 1.31 0.40 0.34 0.90 0.80 1.19 1.13 0.55 0.5158(0.6250) 11 and 18 Heavy F 2.76 2.62 1.44 1.31 0.40 0.34 0.90 0.80 1.19 1.13 0.55 0.5134(0.7500) 10 and 16 Heavy F 2.76 2.62 1.44 1.31 0.40 0.34 0.90 0.80

46、1.19 1.13 0.55 0.51NOTE:(1) Sizes shown in boldface are preferred.3ASME B18.6.9-2010Table 2 Dimensions of Type B, Style 1 Wing NutsECGA DBWing Between BossNominal Size orWing Spread, A Wing Height, B Thickness, C Wings, D Diameter, E Boss Height, GBasic Major Dia. Threadsof Thread per Inch Max. Min.

47、 Max. Min. Max. Min. Max. Min. Max. Min. Max. Min.5 (0.1250) 40 0.78 0.72 0.36 0.30 0.13 0.10 0.28 0.22 0.31 0.28 0.22 0.1610 (0.1900) 24 0.97 0.91 0.45 0.39 0.15 0.12 0.34 0.28 0.39 0.36 0.28 0.2214(0.2500) 20 1.16 1.09 0.56 0.50 0.17 0.14 0.41 0.34 0.47 0.44 0.34 0.28516(0.3125) 18 1.44 1.38 0.67

48、0.61 0.18 0.15 0.50 0.44 0.55 0.52 0.41 0.3438(0.3750) 16 1.72 1.66 0.80 0.73 0.20 0.17 0.59 0.53 0.63 0.60 0.47 0.41716(0.4375) 14 2.00 1.94 0.91 0.84 0.21 0.18 0.69 0.62 0.71 0.68 0.53 0.4712(0.5000) 13 2.31 2.22 1.06 0.94 0.23 0.20 0.78 0.69 0.79 0.76 0.62 0.50916(0.5625) 12 2.59 2.47 1.17 1.05 0

49、.25 0.21 0.88 0.78 0.88 0.84 0.69 0.5658(0.6250) 11 2.84 2.72 1.31 1.19 0.27 0.23 0.94 0.84 0.96 0.92 0.75 0.6234(0.7500) 10 3.31 3.19 1.52 1.39 0.29 0.25 1.10 1.00 1.12 1.08 0.88 0.754ASME B18.6.9-2010Table 3 Dimensions of Type B, Style 2 Wing NutsBECGDAWing Between BossNominal Size orWing Spread, A Wing Height, B Thickness, C Wings, D Diameter, E Boss Height, GBasic Major Dia. Threadsof Thread per Inch Max. Min. Max. Min. Max. Min. Max. Min. Max. Min. Max. Min.5 (0.1250) 40 0.81 0.75 0.62 0.56 0.12 0.09 0.28 0.22 0.31 0.28 0.22 0.1610 (0.1900) 24 1.01 0.95 0.7