ASME A112 19 5-2017 Flush valves and spuds for water closets urinals and tanks (Second Edition).pdf

《ASME A112 19 5-2017 Flush valves and spuds for water closets urinals and tanks (Second Edition).pdf》由会员分享，可在线阅读，更多相关《ASME A112 19 5-2017 Flush valves and spuds for water closets urinals and tanks (Second Edition).pdf（28页珍藏版）》请在麦多课文档分享上搜索。

1、ASME A112.19.5-2017/CSA B45.15-17Flush valves and spuds for water closets, urinals, and tanksLegal Notice for Harmonized Standard Jointly Developed by ASME and CSA GroupIntellectual property rights and ownershipAs between American Society of Mechanical Engineers (“ASME“) and Canadian Standards Assoc

2、iation (Operating as “CSA Group“) (collectively “ASME and CSA Group“) and the users of this document (whether it be in printed or electronic form), ASME and CSA Group are the joint owners of all works contained herein that are protected by copyright, all trade-marks (except as otherwise noted to the

3、 contrary), and all inventions and trade secrets that may be contained in this document, whether or not such inventions and trade secrets are protected by patents and applications for patents. The unauthorized use, modification, copying, or disclosure of this document may violate laws that protect t

4、he intellectual property of ASME and CSA Group and may give rise to a right in ASME and CSA Group to seek legal redress for such use, modification, copying, or disclosure. ASME and CSA Group reserve all intellectual property rights in this document.Disclaimer and exclusion of liabilityThis document

5、is provided without any representations, warranties, or conditions of any kind, express or implied, including, without limitation, implied warranties or conditions concerning this documents fitness for a particular purpose or use, its merchantability, or its non-infringement of any third partys inte

6、llectual property rights. ASME and CSA Group do not warrant the accuracy, completeness, or currency of any of the information published in this document. ASME and CSA Group make no representations or warranties regarding this documents compliance with any applicable statute, rule, or regulation.IN N

7、O EVENT SHALL ASME AND CSA GROUP, THEIR RESPECTIVE VOLUNTEERS, MEMBERS, SUBSIDIARIES, OR AFFILIATED COMPANIES, OR THEIR EMPLOYEES, DIRECTORS, OR OFFICERS, BE LIABLE FOR ANY DIRECT, INDIRECT, OR INCIDENTAL DAMAGES, INJURY, LOSS, COSTS, OR EXPENSES, HOWSOEVER CAUSED, INCLUDING BUT NOT LIMITED TO SPECI

8、AL OR CONSEQUENTIAL DAMAGES, LOST REVENUE, BUSINESS INTERRUPTION, LOST OR DAMAGED DATA, OR ANY OTHER COMMERCIAL OR ECONOMIC LOSS, WHETHER BASED IN CONTRACT, TORT (INCLUDING NEGLIGENCE), OR ANY OTHER THEORY OF LIABILITY, ARISING OUT OF OR RESULTING FROM ACCESS TO OR POSSESSION OR USE OF THIS DOCUMENT

9、, EVEN IF ASME OR CSA GROUP HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES, INJURY, LOSS, COSTS, OR EXPENSES.In publishing and making this document available, ASME and CSA Group are not undertaking to render professional or other services for or on behalf of any person or entity or to perform

10、any duty owed by any person or entity to another person or entity. The information in this document is directed to those who have the appropriate degree of experience to use and apply its contents, and ASME and CSA Group accept no responsibility whatsoever arising in any way from any and all use of

11、or reliance on the information contained in this document.ASME and CSA Group have no power, nor do they undertake, to enforce compliance with the contents of the standards or other documents they jointly publish.Authorized use of this documentThis document is being provided by ASME and CSA Group for

12、 informational and non-commercial use only. The user of this document is authorized to do only the following:If this document is in electronic form: load this document onto a computer for the sole purpose of reviewing it; search and browse this document; and print this document if it is in PDF forma

13、t.Limited copies of this document in print or paper form may be distributed only to persons who are authorized by ASME and CSA Group to have such copies, and only if this Legal Notice appears on each such copy.In addition, users may not and may not permit others to alter this document in any way or

14、remove this Legal Notice from the attached standard; sell this document without authorization from ASME and CSA Group ; or make an electronic copy of this document.If you do not agree with any of the terms and conditions contained in this Legal Notice, you may not load or use this document or make a

15、ny copies of the contents hereof, and if you do make such copies, you are required to destroy them immediately. Use of this document constitutes your acceptance of the terms and conditions of this Legal Notice.Standards Update ServiceASME A112.19.5-2017/CSA B45.15-17May 2017Title: Flush valves and s

16、puds for water closets, urinals, and tanksTo register for e-mail notification about any updates to this publication go to shop.csa.ca click on CSA Update ServiceThe List ID that you will need to register for updates to this publication is 2424675.If you require assistance, please e-mail techsupportc

17、sagroup.org or call 416-747-2233.Visit CSA Groups policy on privacy at www.csagroup.org/legal to find out how we protect your personal information.ASME/CSA StandardASME A112.19.5-2017/CSA B45.15-17 Flush valves and spuds for water closets, urinals, and tanksA trademark of the Canadian Standards Asso

18、ciation and CSA America Inc., operating as “CSA Group”Published in May 2017 by CSA Group A not-for-profit private sector organization178 Rexdale Boulevard, Toronto, Ontario, Canada M9W 1R31-800-463-6727 416-747-4044Visit the CSA Group Online Store at shop.csa.caThe American Society of Mechanical Eng

19、ineers (ASME) Two Park AvenueNew York, NY 10016-5990, USA1-800-843-2763Visit the ASME Online Store at www.asme.orgCommitment for AmendmentsThis Standard is issued jointly by the American Society of Mechanical Engineers (ASME) and the Canadian Standards Association (Operating as “CSA Group”). Amendme

20、nts to this Standard will be made only after processing according to the Standards writing procedures of both ASME and CSA Group. Published in May 2017 by CSA Group A not-for-profit private sector organization 178 Rexdale Boulevard Toronto, Ontario, Canada M9W 1R3 1-800-463-6727 or 416-747-4044Visit

21、 the CSA Group Online Store atshop.csa.caISBN 978-1-4883-0469-9 CSA Group 2017The American Society of Mechanical Engineers (ASME) Two Park Avenue New York, NY 10016-5990 USA 1-800-843-2763Visit the ASME Online Store atwww.asme.orgCopyright 2017 by The American Society of Mechanical Engineers (ASME)T

22、he 2017 edition of this Standard is being issued with an automatic addenda subscription service. The use of addenda allows revisions made in response to public review comments or committee actions to be published as necessary.All rights reserved. No part of this publication may be reproduced in any

23、form whatsoever without the prior permission of the publisher.ASME A112.19.5-2017/CSA B45.15-17 Flush valves and spuds for water closets, urinals, and tanksMay 20171ContentsASME A112 Standards Committee on Plumbing Materials and Equipment 2CSA Technical Committee on Plumbing Fixtures 5CSA/ASME Harmo

24、nization Task Group on Plumbing Fixtures 10Preface 121 Scope 142 Reference publications 143 Definitions and abbreviations 153.1 Definitions 153.2 Abbreviations 154 Design requirements 154.1 Rated temperatures 154.2 Threads 154.3 Overflow tubes 164.4 Spud dimensions 165 Performance requirements and t

25、est methods 165.1 General 165.1.1 Preconditioning 165.1.2 Installation for testing 165.1.3 Flush valve assembly 165.2 Life cycle test 165.2.1 Performance requirements 165.2.2 Test method 165.3 Thread torque test 175.3.1 Performance requirements 175.3.2 Test method 175.4 Fixture and flush valve joint

26、 leak test 175.4.1 Performance requirement 175.4.2 Test method 175.5 Leak rate and accelerated chemical resistance tests 175.5.1 General 175.5.2 Performance requirement 175.5.3 Test methods 186 Markings 196.1 Manufacturers name or trademark 196.2 Packaging 19Annex A (informative) Unit conversion and

27、 rounding criteria 22ASME A112.19.5-2017/CSA B45.15-17 Flush valves and spuds for water closets, urinals, and tanksMay 20172ASME A112 Standards Committee on Plumbing Materials and EquipmentW.M. Smith American Society of Plumbing Engineers, Montgomery, Alabama, USA ChairS. Rawalpindiwala Kohler Co.,

28、Kohler, Wisconsin, USA Vice-ChairT.J. Stessman Kohler Co., Kohler, Wisconsin, USA AlternateR.K. Adler City of San Jose, San Jose, California, USA J.A. Ballanco JB Engineering b) update to markings and packaging requirements;c) update to chemical resistance test procedure requirements; andd) update t

29、o the minimum effective thread length dimension.This Standard is considered suitable for use with conformity assessment within its stated scope.This Standard was prepared by the ASME/CSA Joint Harmonization Task Group on Plumbing Fixtures, under the jurisdiction of the ASME Standards Committee on Pl

30、umbing Materials and Equipment and the CSA Technical Committee on Plumbing Fixtures. The CSA Technical Committee operates under the jurisdiction of the CSA Strategic Steering Committee on Construction and Civil Infrastructure. This Standard has been formally approved by the ASME Standards Committee

31、and the CSA Technical Committee. This Standard was approved as an American National Standard by the American National Standards Institute on May 23, 2017.ASME Notes:1) This standard was developed under procedures accredited as meeting the criteria for American National Standards and it is an America

32、n National Standard. The Standards Committee that approved the code or standard was balanced to assure that individuals from competent and concerned interests have had an opportunity to participate. The proposed Standard was made available for public review and comment that provides an opportunity f

33、or additional public input from industry, academia, regulatory agencies, and the public-at-large.2) ASME does not “approve,” “rate,” or “endorse” any item, construction, proprietary device, or activity.3) ASME does not take any position with respect to the validity of any patent rights asserted in c

34、onnection with any items mentioned in this document, and does not undertake to insure anyone utilizing a standard against liability for infringement of any applicable letters patent, nor assume any such liability. Users of a standard are expressly advised that determination of the validity of any su

35、ch patent rights, and the risk of infringement of such rights, is entirely their own responsibility.4) Participation by federal agency representative(s) or person(s) affiliated with industry is not to be interpreted as government or industry endorsement of this standard.5) ASME accepts responsibilit

36、y for only those interpretations of this document issued in accordance with the established ASME procedures and policies, which precludes the issuance of interpretations by individuals.6) ASME issues written replies to inquiries concerning interpretation of technical aspects of this Standard. All in

37、quiries regarding this Standard, including requests for interpretations, should be addressed to: Secretary, A112 Standards Committee The American Society of Mechanical Engineers Two Park Avenue New York, NY 10016-5990 A request for interpretation should be clear and unambiguous. The request should c

38、ite the applicable edition of the Standard for which the interpretation is being requested. ASME A112.19.5-2017/CSA B45.15-17 Flush valves and spuds for water closets, urinals, and tanksMay 201713 phrase the question as a request for an interpretation of a specific requirement suitable for general u

39、nderstanding and use, not as a request for an approval of a proprietary design or situation. The inquirer may also include any plans or drawings, which are necessary to explain the question; however, they should not contain proprietary names or information.ASME procedures provide for reconsideration

40、 of any interpretation when or if additional information that might affect an interpretation is available. Further, persons aggrieved by an interpretation may appeal to the cognizant ASME Committee.Interpretations are published on the ASME Web site under the Committee Pages at http:/www. asme.org/co

41、des/ as they are issued.CSA Notes:1) Use of the singular does not exclude the plural (and vice versa) when the sense allows.2) Although the intended primary application of this Standard is stated in its Scope, it is important to note that it remains the responsibility of the users of the Standard to

42、 judge its suitability for their particular purpose.3) This publication was developed by consensus, which is defined by CSA Policy governing standardization Code of good practice for standardization as “substantial agreement. Consensus implies much more than a simple majority, but not necessarily un

43、animity”. It is consistent with this definition that a member may be included in the Technical Committee list and yet not be in full agreement with all clauses of this publication.4) To submit a request for interpretation of CSA Standards, please send the following information to inquiriescsa.ca and

44、 include “Request for interpretation” in the subject line: a) define the problem, making reference to the specific clause, and, where appropriate, include an illustrative sketch;b) provide an explanation of circumstances surrounding the actual field condition; andc) where possible, phrase the reques

45、t in such a way that a specific “yes” or “no” answer will address the issue. Committee interpretations are processed in accordance with the CSA Directives and guidelines governing standardization and are published in CSAs periodical Info Update, which is available on the CSA website at http:/standar

46、dsactivities.csa.ca.5) CSA Standards are subject to periodic review, and suggestions for their improvement will be referred to the appropriate committee. To submit a proposal for change to CSA Standards, please send the following information to inquiriescsa.ca and include “Proposal for change” in th

47、e subject line: a) Standard designation (number);b) relevant clause, table, and/or figure number;c) wording of the proposed change; andd) rationale for the change.6) Attention is drawn to the possibility that some of the elements of this Standard may be the subject of patent rights. CSA is not to be

48、 held responsible for identifying any or all such patent rights. Users of this Standard are expressly advised that determination of the validity of any such patent rights is entirely their own responsibility.ASME A112.19.5-2017/CSA B45.15-17 Flush valves and spuds for water closets, urinals, and tan

49、ksMay 201714ASME A112.19.5-2017/CSA B45.15-17Flush valves and spuds for water closets, urinals, and tanks1 Scope1.1 This Standard covers spuds and flush valves for water closet bowls, tanks, and urinals.1.2 In this Standard, “shall” is used to express a requirement, i.e., a provision that the user is obliged to satisfy in order to comply with the standard; “should” is used to express a recommendation or that which is advised but not required; and “may” is used to express an option or that which is permissible within the limits of the standard.Notes acc