ASD-STAN PREN 6092-2007 Aerospace series Receptacle floating double lug (Edition P 2)《航空航天系列 双耳浮动式插座 第P2版》.pdf

《ASD-STAN PREN 6092-2007 Aerospace series Receptacle floating double lug (Edition P 2)《航空航天系列 双耳浮动式插座 第P2版》.pdf》由会员分享，可在线阅读，更多相关《ASD-STAN PREN 6092-2007 Aerospace series Receptacle floating double lug (Edition P 2)《航空航天系列 双耳浮动式插座 第P2版》.pdf（9页珍藏版）》请在麦多课文档分享上搜索。

1、ASD STANDARD NORME ASD ASD NORM prEN 6092 Edition P 2 July 2007 PUBLISHED BY THE AEROSPACE AND DEFENCE INDUSTRIES ASSOCIATION OF EUROPE - STANDARDIZATIONAvenue de Tervuren, 270 - B-1150 Brussels - Tel. + 32 2 775 8126 - Fax. + 32 2 763 3565 - www.asd-stan.orgICS: Supersedes edition P 1 July 2006 Des

2、criptors: ENGLISH VERSION Aerospace series Receptacle, floating, double lug Srie arospatiale Rceptacle, flottant, double patte Luft- und Raumfahrt Haltenocken, schwimmend, zweiseitig This “Aerospace Series“ Prestandard has been drawn up under the responsibility of ASD-STAN (The AeroSpace and Defence

3、 Industries Association of Europe - Standardization). It is published for the needs of the European Aerospace Industry. It has been technically approved by the experts of the concerned Domain following member comments. Subsequent to the publication of this Prestandard, the technical content shall no

4、t be changed to an extent that interchangeability is affected, physically or functionally, without re-identification of the standard. After examination and review by users and formal agreement of ASD-STAN, it will be submitted as a draft European Standard (prEN) to CEN (European Committee for Standa

5、rdization) for formal vote and transformation to full European Standard (EN). The CEN national members have then to implement the EN at national level by giving the EN the status of a national standard and by withdrawing any national standards conflicting with the EN. Edition approved for publicatio

6、n 31 July 2007 Comments should be sent within six months after the date of publication to ASD-STAN Mechanical Domain Copyright 2007 by ASD-STAN prEN 6092:20072 Contents Page Foreword2 1 Scope 3 2 Normative references 3 3 Requirements.4 4 Designation 8 5 Marking .8 6 Technical specification .8 7 Exam

7、ple of installation9 Foreword This standard was reviewed by the Domain Technical Coordinator of ASD-STANs Mechanical Domain. After inquiries and votes carried out in accordance with the rules of ASD-STAN defined in ASD-STANs General Process Manual, this standard has received approval for Publication

8、. prEN 6092:2007 3 1 Scope This standard specifies the dimensions, tolerances, required characteristics and mass of a receptacle for use in fuselage interior equipment and structural applications. This standard shall be used in conjunction with studs per EN 6088 or EN 6105. 2 Normative references Th

9、e following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 2768-1, General tolerances Part 1: Tolerances f

10、or linear and angular dimensions without individual tolerance indications. ISO 8080, Aerospace Anodic treatment of titanium and titanium alloys Sulfuric acid process. EN 2424, Aerospace series Marking of aerospace products. EN 2516, Aerospace series Passivation of corrosion resistant steels and deco

11、ntamination of nickel base alloys. EN 2808, Aerospace series Anodizing of titanium and titanium alloys. EN 6088, Aerospace series Stud. 1)EN 6089, Aerospace series Washer, retaining, for usage with stud EN 6088.1)EN 6090, Aerospace series Washer, retaining.1)EN 6091, Aerospace series Circlip. 1)EN 6

12、094, Aerospace series Washer, spring, countersunk. 1)EN 6095, Aerospace series Rotary fasteners Structural and non-structural applications Technical specification. 1)EN 6105, Aerospace series Stud with shoulder. 1)EN 10088-3, Stainless steels Part 3: Technical delivery conditions for semi-finished p

13、roducts, bars, rods, wire, sections and bright products of corrosion resisting steels for general purposes. EN 10270-1, Steel wire for mechanical springs Part 1: Patented cold drawn unalloyed spring steel wire. EN 10270-3, Steel wire for mechanical springs Part 3: Stainless spring steel wire. DIN 17

14、850, Titanium, chemical composition. AMS 2700, Passivation of corrosion resistant steels. 2)1) Published as ASD Prestandard at the date of publication of this standard. 2) Published by: Society of Automotive Engineers (SAE), 400 Commonwealth Drive, Warrendale, PA 15096-0001, USA. prEN 6092:20074 AMS

15、 5528, Steel, corrosion resistant, sheet, strip and plate, 17Cr-7.1Ni-1.1Al, solution heat treated, precipitation hardenable. 2)AS 8879, Screw threads - UNJ profile, inch controlled radius root with increased minor diameter. 2)MIL-DTL-83488, Coating, aluminium, high purity. 3)MIL-PRF-46010, Lubrican

16、t, solid film, heat cured, corrosion inhibiting. 3)3 Requirements 3.1 Configuration, dimensions and tolerances The configuration, dimensions and tolerances shall conform with Figure 1. Dimensions and tolerances are expressed in millimetres. Tolerances not specified shall be in accordance with ISO 27

17、68-1 (Tolerance class: ISO 2768-m). All dimensions and tolerances apply after surface treatment. All burrs to be removed/sharp edges to be broken. 3) Published by: Department of Defense (DoD), the Pentagon, Washington, D.C., 20307, USA. prEN 6092:20075 YY ZZTreadperAS88798-32UNC-3A2 leadScrewPlateSp

18、ringsWashersCapMarking see clause 517,45 0,1 2,50 0,1R311,2013,615,0 max10,5 max14,5 max0,640,6 0,3 3,0 0,30,2 0,30,6 0,15AAA-A0,9 0,1Key 1 Marking, see Clause 5 2 Plate Part A 3 Washers 4 Cap 5 Springs 6 Screw 7 Thread per AS 8879, 8-32UNC-3A, 2 lead Figure 1 Configuration, dimensions and tolerance

19、s 42 625 317 Barrel Part B prEN 6092:20076 3.2 Material and surface treatment See Table 1. Table 1 Material and surface treatment Dash number Finish code Element Material Finish Lubricant Screw Corrosion resistant steel 1.4303 per EN 10088-3 Dry film per MIL-PRF-46010 aCap Corrosion resistant steel

20、1.4404 per EN 10088-3 bPlate Corrosion resistant steel per AMS 5528 Springs Corrosion resistant steel 1.4310 per EN 10270-1 or EN 10270-3 None 01 Washers Corrosion resistant steel per AMS 5528 Passivated per AMS 2700 or EN 2516 Dry film per MIL-PRF-46010 Screw Corrosion resistant steel 1.4303 per EN

21、 10088-3 Dry film per MIL-PRF-46010 aCap Corrosion resistant steel 1.4404 per EN 10088-3 bPlate Corrosion resistant steel per AMS 5528 IVD coating per MIL-DTL-83488 type II, class 3 Springs Corrosion resistant steel 1.4310 per EN 10270-1 or EN 10270-3 None 01 V Washers Corrosion resistant steel per

22、AMS 5528 Dry film per MIL-PRF-46010 Screw Corrosion resistant steel 1.4303 per EN 10088-3 Passivated per AMS 2700 or EN 2516 Dry film per MIL-PRF-46010 aCap Titanium alloy 3.7035 per DIN 17850 Anodized per EN 2808 or ISO 8080 Plate Corrosion resistant steel per AMS 5528 Springs Corrosion resistant s

23、teel 1.4310 per EN 10270-1 or EN 10270-3 None 02 S Washers Corrosion resistant steel per AMS 5528 Passivated per AMS 2700 or EN 2516 Dry film per MIL-PRF-46010 aAt manufacturers discretion. bCarbon content of 0,3 % max. permitted after sintering process. prEN 6092:20077 3.3 Mass See Table 2. Table 2

24、 Mass Dash number Finish code Mass (Ref.) kg/1 000 pieces 01 6,7 01 V 6,7 02 S 5,17 3.4 Floatability Minimum floatability: 0,64 mm radially from center 3.5 Static values Maximum axial tensile load: 6 000 N Locking torque: 2,8 Nm 3,2 Nm 3.6 Operating temperature This receptacle shall be used in the t

25、emperature range of 55 C to 150 C. 3.7 Procurement codes Receptacles may be procured as separate parts as shown in Table 3. The bags shall be identified with a label carrying the part designation. Table 3 Procurement codes for EN 6092 Procurement Code Part Quantity supplied per bag No. Code Plate an

26、d Barrel assembly (Parts A and B on Figure 1) 50 A Plate (Part A on Figure 1) 50 B Barrel assembly (Part B on Figure 1) 50 prEN 6092:20078 4 Designation EXAMPLE Description block RECEPTACLE Identity block EN6092-01VB Number of this standard Dash number (see Tables 1 and 2) Material and finish code (

27、see Tables 1 and 2) Procurement code (see Table 3) NOTE If necessary, the code I9005 shall be placed between the description block and the identity block. 5 Marking EN 2424, style F 6 Technical specification EN 6095 prEN 6092:20079 7 Example of installation RECEPTACLE per EN6092WASHER per EN6094STUD per EN6088 or EN6105Key 1 Washer per EN 6094 2 Receptacle per EN 6092 3 Stud per EN 6088 or EN 6105 NOTE Retaining washer EN 6090 or retaining washer EN 6089 and circlip EN 6091 respectively not shown. Refer to relevant standard for details of installation. Figure 2 Example of installation 1 3 2