ARMY UFGS-14 21 23-2009 ELECTRIC TRACTION PASSENGER ELEVATORS《电力牵引客运电梯》.pdf

《ARMY UFGS-14 21 23-2009 ELECTRIC TRACTION PASSENGER ELEVATORS《电力牵引客运电梯》.pdf》由会员分享，可在线阅读，更多相关《ARMY UFGS-14 21 23-2009 ELECTRIC TRACTION PASSENGER ELEVATORS《电力牵引客运电梯》.pdf（29页珍藏版）》请在麦多课文档分享上搜索。

1、*USACE / NAVFAC / AFCESA / NASA UFGS-14 21 23 (February 2009)-Preparing Activity: USACE SupersedingUFGS-14 21 23 (July 2007)UNIFIED FACILITIES GUIDE SPECIFICATIONSReferences are in agreement with UMRL dated January 2009*SECTION TABLE OF CONTENTSDIVISION 14 - CONVEYING EQUIPMENTELECTRIC TRACTION PASS

2、ENGER ELEVATORS02/09PART 1 GENERAL1.1 REFERENCES1.2 SYSTEM DESCRIPTION1.2.1 Fire Protection System1.2.2 Miscellaneous Requirements1.2.3 Provisions for Earthquake Protection1.3 SUBMITTALS1.4 QUALITY ASSURANCE1.4.1 Elevator Specialist1.4.2 Elevator Inspector1.4.3 Welders Qualifications1.4.4 Detail Dra

3、wings1.5 SCHEDULING1.6 WARRANTY1.7 MAINTENANCE AND REPAIR ACTION PLAN1.7.1 Maintenance and Diagnostic Tools1.7.2 Keys for Elevator Key SwitchesPART 2 PRODUCTS2.1 PASSENGER ELEVATORS2.1.1 Basic Requirements2.1.2 Cab Enclosures and Door Finishes2.2 SPECIAL OPERATION AND CONTROL2.2.1 Firefighters Servi

4、ce2.2.2 Smoke Detectors2.2.3 Fire Sprinklers2.2.4 Top-of-Car Operating Device2.2.5 Hoistway Access Switches2.2.6 Independent Service2.2.7 Elevator Operation2.2.7.1 Single, Two-Stop, Automatic Operation2.2.7.2 Selective Collective Automatic Operation2.2.7.3 Duplex Selective Collective Automatic Opera

5、tions2.2.7.4 Group Automatic Operation2.2.8 Parking Switch2.2.9 Hospital Emergency Commandeering ServiceSECTION 14 21 23 Page 1Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-2.3 ELEVATOR MACHINE2.4 CONTROL EQUIPMENT2.4.1 Motor Control Equipment2.4.1

6、.1 Motor Generator Set2.4.1.2 SCR Control or VVVF AC Control2.4.2 Logic Control2.4.2.1 On-Board Diagnostic Panel2.4.2.2 External Port2.4.2.3 Repair Requirements2.5 OPERATING PANELS, SIGNAL FIXTURES, AND COMMUNICATIONS CABINETS2.5.1 Capacity and Data Plates2.5.2 Car and Hall Buttons2.5.3 Passenger Ca

7、r-Operating Panel2.5.3.1 Passenger Controls2.5.3.2 Service Controls2.5.3.3 Certificate Window2.5.4 Freight Car-Operating Panel2.5.4.1 Passenger Controls2.5.4.2 Service Controls2.5.4.3 Certificate Window2.5.5 Semi-Selective Door Operation2.5.6 Full-Selective Door Operation2.5.7 Switches and Devices2.

8、5.8 In-Car Position and Direction Indicator and Signal2.5.8.1 In-Car Position Indicator and Signal2.5.8.2 In-Car Direction Indicator and Signal2.5.9 Landing Position and Direction Indicator and Signal2.5.9.1 Landing Position Indicator and Signal2.5.9.2 Landing Direction Indicator and Signal2.6 HOIST

9、WAY AND CAR EQUIPMENT2.6.1 Car and Counterweight Guide Rails and Fastenings2.6.2 Car and Counterweight Buffers2.6.3 Pit Equipment2.6.3.1 Pit “STOP“ Switch2.6.3.2 Ladder2.6.3.3 Lighting of Pits2.6.4 Terminal Stopping Devices2.6.5 Wiring and Traveling Cables2.6.6 Emergency Signaling Devices2.7 PASSENG

10、ER CAR AND HOISTWAY DOOR ACCESSORIES2.8 PASSENGER ELEVATOR GUIDES, PLATFORM, AND ENCLOSURE2.8.1 Roller Guides2.8.2 Car Frame and Platform2.8.3 Car Enclosure, Car Door, and Car Illumination2.8.3.1 Return Panels, Entrance Columns, Cove Base, and Transom2.8.3.2 Car Top2.8.3.3 Car Door2.8.3.4 Car Entran

11、ce Sill2.8.3.5 Carpet2.9 PASSENGER ELEVATOR HOISTWAY DOORS AND ENTRANCES2.9.1 Hoistway Entrance Frames2.9.2 Hoistway Entrance Sills2.9.3 Hoistway Entrance Doors2.9.4 Entrance Fascias and Dust Covers2.9.5 Hoistway Ventilation2.10 HANDICAPPED AND MEDICAL SERVICES ACCESS2.10.1 Provision for Handicapped

12、2.10.2 Emergency Medical Services2.11 EMERGENCY POWER OPERATIONSECTION 14 21 23 Page 2Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-PART 3 EXECUTION3.1 INSTALLATION3.1.1 Traveling Cables3.1.2 Structural Members3.1.3 Safety Guards3.1.4 Miscellaneous

13、 Requirements3.1.5 Firefighters Service3.2 FIELD QUALITY CONTROL3.2.1 Testing Materials and Instruments3.2.2 Field Tests3.2.2.1 Endurance Tests3.2.2.2 Speed Tests3.2.2.3 Leveling Tests3.2.2.4 Insulation Resistance Tests3.2.2.5 Brake Test3.2.2.6 Buffer Tests3.2.2.7 Temperature Rise Tests3.2.2.8 Balan

14、ce Tests3.2.2.9 Motor Ampere Tests3.3 MAINTENANCE SERVICE TRAINING- End of Section Table of Contents -SECTION 14 21 23 Page 3Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-*USACE / NAVFAC / AFCESA / NASA UFGS-14 21 23 (February 2009)-Preparing Activ

15、ity: USACE SupersedingUFGS-14 21 23 (July 2007)UNIFIED FACILITIES GUIDE SPECIFICATIONSReferences are in agreement with UMRL dated January 2009*SECTION 14 21 23ELECTRIC TRACTION PASSENGER ELEVATORS02/09*NOTE: This guide specification covers the requirements for electric traction passenger elevators.E

16、dit this guide specification for project specific requirements by adding, deleting, or revising text. For bracketed items, choose applicable item(s) or insert appropriate information.Remove information and requirements not required in respective project, whether or not brackets are present.Comments

17、and suggestions on this guide specification are welcome and should be directed to the technical proponent of the specification. A listing of technical proponents, including their organization designation and telephone number, is on the Internet.Recommended changes to a UFGS should be submitted as a

18、Criteria Change Request (CCR).*PART 1 GENERAL*NOTE: All Navy facility designs which include elevators must comply with the “NAVFAC Elevator Design Guide“. This guide is available from the Whole Building Design Guide web site, DoD page (http:/dod.wbdg.org), from the NAVFAC drop down menu - Interim Te

19、chnical guidance.Use Section 14 21 13 for ELECTRIC TRACTION FREIGHT ELEVATORS.NOTE: Any editing of non-bracketed requirements in this specification must be approved through the NAVFAC Elevator Program.*SECTION 14 21 23 Page 4Provided by IHSNot for ResaleNo reproduction or networking permitted withou

20、t license from IHS-,-,-1.1 REFERENCES*NOTE: This paragraph is used to list the publications cited in the text of the guide specification. The publications are referred to in the text by basic designation only and listed in this paragraph by organization, designation, date, and title.Use the Referenc

21、e Wizards Check Reference feature when you add a RID outside of the Sections Reference Article to automatically place the reference in the Reference Article. Also use the Reference Wizards Check Reference feature to update the issue dates.References not used in the text will automatically be deleted

22、 from this section of the project specification when you choose to reconcile references in the publish print process.*The publications listed below form a part of this specification to the extent referenced. The publications are referred to within the text by the basic designation only.AMERICAN WELD

23、ING SOCIETY (AWS)AWS B2.1 (2005; Errata 2006; Errata 2006) Welding Procedure and Performance QualificationAWS D1.1/D1.1M (2008) Structural Welding Code - SteelASME INTERNATIONAL (ASME)ASME A17.1 (2007) Safety Code for Elevators and EscalatorsASME A17.2 (2007) Guide for Inspection of Elevators, Escal

24、ators, and Moving WalksASME A17.3 (2005) Safety Code for Existing Elevators and Escalators-Interpretations No. 6ASME QEI-1 (2007) Standard for the Qualification of Elevator InspectorsASTM INTERNATIONAL (ASTM)ASTM E 2074 (2000e1) Standard Test Method for Fire Tests of Door Assemblies, Including Posit

25、ive Pressure Testing of Side-Hinged and Pivoted Swinging Door AssembliesINTERNATIONAL CODE COUNCIL (ICC)ICC IBC (2006; Errata 2006; Errata 2007; SECTION 14 21 23 Page 5Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-Supplement 2007; Errata 2007) Inte

26、rnational Building CodeICC IPC (2006; Supplement 2007) International Plumbing CodeNATIONAL ELECTRICAL MANUFACTURERS ASSOCIATION (NEMA)NEMA MG 1 (2007; Errata 2008) Standard for Motors and GeneratorsNATIONAL FIRE PROTECTION ASSOCIATION (NFPA)NFPA 101 (2008) Life Safety Code, 2006 EditionNFPA 70 (2007

27、; AMD 1 2008) National Electrical Code - 2008 EditionNFPA 72 (2006) National Fire Alarm CodeU.S. NATIONAL ARCHIVES AND RECORDS ADMINISTRATION (NARA)29 CFR 1910.27 Fixed Ladders36 CFR 1191 Americans with Disabilities Act (ADA) Accessibility Guidelines for Buildings and Facilities1.2 SYSTEM DESCRIPTIO

28、NProvide a pre-engineered elevator system, by manufacturer regularly engaged in the manufacture of elevator systems, that complies with ASME A17.1 and ASME A17.2 in their entirety, and additional requirements specified herein.1.2.1 Fire Protection System*NOTE: Hoistway vents may be activated elevato

29、r lobby smoke detectors. Detectors do not have to be placed in hoistways per IBC/NFPA 72.*Provide a fire protection system complying with the applicable provisions of NFPA 72, NFPA 101, and ASME A17.1. Detailed specification information is stated in Section 28 31 74.00 20 INTERIOR FIRE DETECTION AND

30、 ALARM SYSTEM. Additional fire protection requirements are found in Section 28 31 02.00 20 FIRE ALARM REPORTING SYSTEMS - DIGITAL COMMUNICATORS; 21 13 13.00 20 WET PIPE SPRINKLER SYSTEM, FIRE PROTECTION; and Section 26 20 00 INTERIOR DISTRIBUTION SYSTEM.1.2.2 Miscellaneous RequirementsSubmit one set

31、 of wiring diagrams, in plastic or glass cover, framed and mounted in elevator machine room for revised building electrical system, if needed, to make supplied elevator system function as specified. Deliver other sets to Contracting Officer. Coded diagrams are not acceptable unless adequately identi

32、fied. Submit calculations for the Reaction Loads imposed on the building by the elevator system and Heat Loads generated by the elevator system.SECTION 14 21 23 Page 6Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-1.2.3 Provisions for Earthquake Pro

33、tection*NOTE: Provide seismic protection as covered by ASME A17.1, Part XXIV. Provide fastenings, attachments, and restraints for prevention of seismic damage in detail by registered structural engineer whose seal is applied to drawings or sketches. Use forces of 1.0 G horizontal and 1.0 G vertical

34、or heavier.*This facility is located in seismic zone 3 4, and shall comply with all ASME A17.1, Part XXIV requirements as applicable by location.1.3 SUBMITTALS*NOTE: Review submittal description (SD) definitions in Section 01 33 00 SUBMITTAL PROCEDURES and edit the following list to reflect only the

35、 submittals required for the project. Submittals should be kept to the minimum required for adequate quality control.A “G” following a submittal item indicates that the submittal requires Government approval. Some submittals are already marked with a “G”. Only delete an existing “G” if the submittal

36、 item is not complex and can be reviewed through the Contractors Quality Control system. Only add a “G” if the submittal is sufficiently important or complex in context of the project.For submittals requiring Government approval on Army projects, a code of up to three characters within the submittal

37、 tags may be used following the “G“ designation to indicate the approving authority. Codes for Army projects using the Resident Management System (RMS) are: “AE“ for Architect-Engineer; “DO“ for District Office (Engineering Division or other organization in the District Office); “AO“ for Area Office

38、; “RO“ for Resident Office; and “PO“ for Project Office. Codes following the “G“ typically are not used for Navy, Air Force, and NASA projects.Choose the first bracketed item for Navy, Air Force and NASA projects, or choose the second bracketed item for Army projects.*Government approval is required

39、 for submittals with a “G“ designation; submittals not having a “G“ designation are for Contractor Quality Control approval.for information only. When used, a designation following the “G“ designation identifies the office that will review the submittal for the Government. Submit the following in ac

40、cordance with Section 01 33 00 SUBMITTAL PROCEDURES:SD-02 Shop DrawingsSECTION 14 21 23 Page 7Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-Detail Drawings; G; G, _Passenger Elevators and accessories; G; G, _Supporting systems; G; G, _Machinery and

41、 controls, Heat Loads; G; G, _ Wiring diagrams; G; G, _Sequence of operations; G; G, _SD-03 Product DataPassenger Elevators and accessories; G; G, _Elevator supporting systems; G; G, _Data sheets; G; G, _Maintenance and diagnostic tools; G; G, _Logic control; G; G, _SD-05 Design Data*NOTE: Use ASME

42、A17.1, Appendix F, for locations in seismic risk zone 3 or greater. Use ASME 17.3 for Existing Elevators.*Reaction loads; G; G, _SD-07 CertificatesQuality Assurance for Elevator Inspector and SpecialistWelders Qualifications; G; G, _SD-10 Operation and Maintenance DataPassenger Elevators, Data Packa

43、ge 4; G; G, _Submit in accordance with Section 01 78 23 OPERATION AND MAINTENANCE DATA.Maintenance and Repair Action Plan; G; G, _1.4 QUALITY ASSURANCE1.4.1 Elevator SpecialistWork specified in this section shall be performed in compliance with ASME A17.3 under the direct guidance of the Elevator Specialistwho is regularly engaged in the installation and maintenance of the type and complexity of elevator system specified in the contract documents, and who served in a similar capacity for