ARMY UFGS-08 34 02-2009 BULLET-RESISTANT COMPONENTS《防弹组件》.pdf

《ARMY UFGS-08 34 02-2009 BULLET-RESISTANT COMPONENTS《防弹组件》.pdf》由会员分享，可在线阅读，更多相关《ARMY UFGS-08 34 02-2009 BULLET-RESISTANT COMPONENTS《防弹组件》.pdf（31页珍藏版）》请在麦多课文档分享上搜索。

1、*USACE / NAVFAC / AFCESA / NASA UFGS-08 34 02 (August 2009)-Preparing Activity: USACE SupersedingUFGS-08 34 02 (April 2006)UNIFIED FACILITIES GUIDE SPECIFICATIONSReferences are in agreement with UMRL dated July 2009*SECTION TABLE OF CONTENTSDIVISION 08 - OPENINGSSECTION 08 34 02BULLET-RESISTANT COMP

2、ONENTS08/09PART 1 GENERAL1.1 REFERENCES1.2 SYSTEM DESCRIPTION1.2.1 Design Requirements1.2.2 Performance Requirements1.3 SUBMITTALS1.4 QUALITY ASSURANCE1.5 DELIVERY, STORAGE, AND HANDLING1.6 SCHEDULING1.7 WARRANTYPART 2 PRODUCTS2.1 MATERIALS AND COMPONENTS2.2 ELECTRICAL WIRING2.3 BULLET-RESISTANT STE

3、EL PERSONNEL DOORS2.3.1 Fire Rated Doors2.3.2 Sound Rated Doors2.3.3 Door and Frame Fabrication2.3.4 Sidelight Frames2.3.5 Preparation for Hardware2.3.6 Hardware2.3.6.1 Mortise Locks and Latchsets2.3.6.2 Hinges2.3.6.3 Electric Strikes2.3.6.4 Door Closers2.3.6.5 Door Stops and Holders2.3.7 Frame Anch

4、ors2.3.8 Weatherstripping2.3.9 Louvers for Doors2.4 BULLET-RESISTANT LOUVERS2.5 BULLET-RESISTANT STEEL BIFOLD DOORS, FRAMES, AND HARDWARE2.5.1 Testing2.5.2 Bifold Doors2.5.3 Power OperatorsSECTION 08 34 02 Page 1Provided by IHSNot for ResaleNo reproduction or networking permitted without license fro

5、m IHS-,-,-2.5.3.1 Pneumatic Operators2.5.3.2 Electric Operators2.5.4 Safety Device2.6 BULLET-RESISTANT STEEL WINDOWS2.6.1 Glazing Materials2.6.1.1 Laminated Glass2.6.1.2 Acrylic Plastic Sheets2.6.1.3 Polycarbonate Plastic Sheets2.6.1.4 Glass/Plastic Laminate Glazing2.6.1.5 Glass/Plastic Air-Gap Glaz

6、ing2.6.2 Adhesive Interlayer Materials2.6.3 Sealants2.6.4 Deal Trays2.7 BULLET-RESISTANT SPEAKING APERTURES2.8 BULLET-RESISTANT GUNPORTS2.9 BULLET-RESISTANT PASS-THROUGH DRAWER2.10 BULLET-RESISTANT PREFABRICATED MODULAR ENCLOSURE2.11 ACCESSORIES2.12 LABELING2.13 SHOP/FACTORY FINISHING2.13.1 Ferrous

7、Metal2.13.2 Galvanizing2.13.3 AluminumPART 3 EXECUTION3.1 EXAMINATION3.2 FRAMED INSTRUCTIONS3.3 INSTALLATION3.4 FASTENERS3.5 CORROSION PROTECTION - DISSIMILAR MATERIALS3.6 ELECTRICAL WORK3.7 ADJUSTING/CLEANING- End of Section Table of Contents -SECTION 08 34 02 Page 2Provided by IHSNot for ResaleNo

8、reproduction or networking permitted without license from IHS-,-,-*USACE / NAVFAC / AFCESA / NASA UFGS-08 34 02 (August 2009)-Preparing Activity: USACE SupersedingUFGS-08 34 02 (April 2006)UNIFIED FACILITIES GUIDE SPECIFICATIONSReferences are in agreement with UMRL dated July 2009*SECTION 08 34 02BU

9、LLET-RESISTANT COMPONENTS08/09*NOTE: This section covers requirements for bullet resistant components including doors, windows, louvers, gunports, pass drawers, deal trays, and speaking apertures.Edit this guide specification for project specific requirements by adding, deleting, or revising text. F

10、or bracketed items, choose applicable items(s) or insert appropriate information.Remove information and requirements not required in respective project, whether or not brackets are present.Comments and suggestions on this guide specification are welcome and should be directed to the technical propon

11、ent of the specification. A listing of technical proponents, including their organization designation and telephone number, is on the Internet.Recommended changes to a UFGS should be submitted as a Criteria Change Request (CCR).*PART 1 GENERAL1.1 REFERENCES*NOTE: This paragraph is used to list the p

12、ublications cited in the text of the guide specification. The publications are referred to in the text by basic designation only and listed in this paragraph by organization, designation, date, and title.Use the Reference Wizards Check Reference feature when you add a RID outside of the Sections Ref

13、erence Article to automatically place the reference in the Reference Article. Also use the SECTION 08 34 02 Page 3Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-Reference Wizards Check Reference feature to update the issue dates.References not used

14、in the text will automatically be deleted from this section of the project specification when you choose to reconcile references in the publish print process.*The publications listed below form a part of this specification to the extent referenced. The publications are referred to within the text by

15、 the basic designation only.AIR MOVEMENT AND CONTROL ASSOCIATION INTERNATIONAL (AMCA)AMCA 500-D (1998) Laboratory Methods of Testing Dampers for RatingALUMINUM ASSOCIATION (AA)AA DAF-45 (2003) Designation System for Aluminum FinishesAMERICAN ARCHITECTURAL MANUFACTURERS ASSOCIATION (AAMA)AAMA 611 (19

16、98) Voluntary Specification for Anodized Architectural AluminumASTM INTERNATIONAL (ASTM)ASTM A 123/A 123M (2009) Standard Specification for Zinc (Hot-Dip Galvanized) Coatings on Iron and Steel ProductsASTM A 653/A 653M (2009) Standard Specification for Steel Sheet, Zinc-Coated (Galvanized) or Zinc-I

17、ron Alloy-Coated (Galvannealed) by the Hot-Dip ProcessASTM C 1036 (2006) Standard Specification for Flat GlassASTM C 1048 (2004) Standard Specification for Heat-Treated Flat Glass - Kind HS, Kind FT Coated and Uncoated GlassASTM C 1172 (2009) Standard Specification for Laminated Architectural Flat G

18、lassASTM D 1003 (2007e1) Haze and Luminous Transmittance of Transparent PlasticsASTM D 1044 (2008) Resistance of Transparent Plastics to Surface AbrasionASTM D 1922 (2009) Propagation Tear Resistance of Plastic Film and Thin Sheeting by Pendulum MethodSECTION 08 34 02 Page 4Provided by IHSNot for Re

19、saleNo reproduction or networking permitted without license from IHS-,-,-ASTM D 256 (2006e1) Determining the Izod Pendulum Impact Resistance of PlasticsASTM D 3595 (2002; R 2007) Polychlorotrifluoroethylene (PCTFE) Extruded Plastic Sheet and FilmASTM D 3951 (1998; R 2004) Commercial PackagingASTM D

20、4093 (1995; R 2005e1) Photoelastic Measurements of Birefringence and Residual Strains in Transparent or Translucent Plastic MaterialsASTM D 4802 (2002) Poly(Methyl Methacrylate) Acrylic Plastic SheetASTM D 542 (2000; R 2006) Index of Refraction of Transparent Organic PlasticsASTM D 5420 (2004) Impac

21、t Resistance of Flat, Rigid Plastic Specimen by Means of a Strike Impacted by a Falling Weight (Gardner Impact)ASTM D 570 (1998; R 2005) Standard Test Method for Water Absorption of PlasticsASTM D 635 (2006) Standard Test Method for Rate of Burning and/or Extent and Time of Burning of Self-Supportin

22、g Plastics in a Horizontal PositionASTM D 638 (2008) Standard Test Method for Tensile Properties of PlasticsASTM D 648 (2007) Deflection Temperature of Plastics Under Flexural Load in the Edgewise PositionASTM D 696 (2008) Standard Test Method for Coefficient of Linear Thermal Expansion of Plastics

23、Between -30 degrees C and 30 degrees C With a Vitreous Silica DilatometerASTM D 792 (2008) Density and Specific Gravity (Relative Density) of Plastics by DisplacementASTM D 882 (2009) Tensile Properties of Thin Plastic SheetingASTM D 905 (2008e1) Strength Properties of Adhesive Bonds in Shear by Com

24、pression LoadingASTM E 1300 (2007e1) Determining Load Resistance of Glass in BuildingsASTM E 168 (2006) General Techniques of Infrared SECTION 08 34 02 Page 5Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-Quantitative AnalysisASTM E 169 (2004) Gener

25、al Techniques of Ultraviolet-Visible Quantitative AnalysisASTM E 204 (1998; R 2007) Identification of Material by Infrared Absorption Spectroscopy, Using the ASTM Coded Band and Chemical Classification IndexASTM E 831 (2006) Linear Thermal Expansion of Solid Materials by Thermomechanical AnalysisAST

26、M E 90 (2004) Standard Test Method for Laboratory Measurement of Airborne Sound Transmission Loss of Building Partitions and ElementsASTM F 1233 (2008) Security Glazing Materials and SystemsASTM F 428 (2009) Intensity of Scratches on Aerospace Glass EnclosuresASTM F 520 (1997; R 2004) Environmental

27、Resistance of Aerospace TransparenciesASTM F 521 (1983; R 2004) Bond Integrity of Transparent LaminatesASTM F 548 (2009) Intensity of Scratches on Aerospace Transparent PlasticsASTM F 735 (2006) Abrasion Resistance of Transparent Plastics and Coatings Using the Oscillating Sand MethodASTM F 791 (199

28、6; R 2008) Stress Crazing of Transparent PlasticsASTM G 155 (2005a) Operating Xenon Arc Light Apparatus for Exposure of Non-Metallic MaterialsBUILDERS HARDWARE MANUFACTURERS ASSOCIATION (BHMA)ANSI/BHMA A156.115 (2006) Hardware Preparation in Steel Doors and Steel FramesBHMA A156.1 (2006) Butts and H

29、ingesBHMA A156.13 (2005) Mortise Locks Test Procedures and Acceptance CriteriaNATIONAL ASSOCIATION OF ARCHITECTURAL METAL MANUFACTURERS (NAAMM)NAAMM HMMA 810 (1987) Hollow Metal DoorsNAAMM HMMA 820 (1987) Hollow Metal FramesNAAMM HMMA 830 (2002) Hardware Selection for Hollow Metal Doors and FramesNA

30、AMM HMMA 840 (1999) Installation and Storage of Hollow Metal Doors and FramesNAAMM HMMA 850 (2000) Fire Rated Hollow Metal Doors and FramesNAAMM HMMA 862 (2003) Guide Specifications for Commercial Security Hollow Metal Doors and FramesNATIONAL ELECTRICAL MANUFACTURERS ASSOCIATION (NEMA)NEMA ICS 2 (2

31、000; Errata 2002; R 2005; Errata 2006) Standard for Industrial Control and Systems: Controllers, Contactors, and Overload Relays Rated Not More than 2000 Volts AC or 750 Volts DC: Part 8 - Disconnect Devices for Use in Industrial Control EquipmentNEMA ICS 6 (1993; R 2006) Standard for Industrial Con

32、trols and Systems EnclosuresNEMA MG 1 (2007; Errata 2008) Standard for Motors and GeneratorsNATIONAL FIRE PROTECTION ASSOCIATION (NFPA)NFPA 70 (2008; AMD 1 2008) National Electrical Code - 2008 EditionNFPA 80 (2006; Errata 2008; Errata 2008) Standard for Fire Doors and Other Opening ProtectivesSECTI

33、ON 08 34 02 Page 7Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-NATIONAL INSTITUTE OF JUSTICE (NIJ)NIJ Std 0108.01 (1985) Ballistic Resistant Protective MaterialsU.S. DEPARTMENT OF STATE (SD)SD Std-01.01 (1993 Rev G Amended; Inx Certified Prod/Mfg)

34、 Certification Standard Forced Entry and Ballistic Resistance of Structural SystemsU.S. NAVAL FACILITIES ENGINEERING SERVICE CENTER (NFESC)NFESC CR 80.025 (1980) Testing and Evaluation of Attack Resistance and Hardening Retrofits of Marine Barrack Construction Types to Small Arms Multiple Impact Thr

35、eatUNDERWRITERS LABORATORIES (UL)UL 752 (2005; Rev thru Dec 2006) Bullet-Resisting Equipment1.2 SYSTEM DESCRIPTION*NOTE: In the event that the designer chooses to design and detail the component for shop fabrication, the materials and construction should be specified in Section 05 50 13 MISCELLANEOU

36、S METAL FABRICATIONS.Bullet-resisting ratings of metals shall be determined by ballistics tests in accordance with the threat specified in paragraph COMPONENT TEST REQUIREMENTS.*1.2.1 Design RequirementsProvide bullet resistant components conforming to the requirements specified for the particular i

37、tems and, as much as possible, complete assemblies by a single manufacturer.1.2.2 Performance RequirementsAll items specified shall be bullet resistant to the threat specified. Movable and operable components shall operate smoothly and freely. When a reference for performance is listed, operation sh

38、all conform to referenced requirements.1.3 SUBMITTALS*NOTE: Review submittal description (SD) definitions in Section 01 33 00 SUBMITTAL PROCEDURES and edit the following list to reflect only the submittals required for the project. Submittals should be kept SECTION 08 34 02 Page 8Provided by IHSNot

39、for ResaleNo reproduction or networking permitted without license from IHS-,-,-to the minimum required for adequate quality control.A “G” following a submittal item indicates that the submittal requires Government approval. Some submittals are already marked with a “G”. Only delete an existing “G” i

40、f the submittal item is not complex and can be reviewed through the Contractors Quality Control system. Only add a “G” if the submittal is sufficiently important or complex in context of the project.For submittals requiring Government approval on Army projects, a code of up to three characters withi

41、n the submittal tags may be used following the “G“ designation to indicate the approving authority. Codes for Army projects using the Resident Management System (RMS) are: “AE“ for Architect-Engineer; “DO“ for District Office (Engineering Division or other organization in the District Office); “AO“

42、for Area Office; “RO“ for Resident Office; and “PO“ for Project Office. Codes following the “G“ typically are not used for Navy, Air Force, and NASA projects.Choose the first bracketed item for Navy, Air Force and NASA projects, or choose the second bracketed item for Army projects.*Government appro

43、val is required for submittals with a “G“ designation; submittals not having a “G“ designation are for Contractor Quality Control approval. information only. When used, a designation following the “G“ designation identifies the office that will review the submittal for the Government. Submit the fol

44、lowing in accordance with Section 01 33 00 SUBMITTAL PROCEDURES:*NOTE: Submittals SD-03 and SD-10, are to be used only when bifold doors are part of the work. Edit out those paragraphs if no bifold doors are required in the work.*SD-02 Shop DrawingsInstallation; G; G, _Drawings containing complete w

45、iring and schematic diagrams, where appropriate, and any other details required to demonstrate that the system has been coordinated and will properly function as a unit. Drawings shall show proposed layout and anchorage of components and appurtenances, and relationship to other parts of work including clearances for operation and maintenance. Drawings sufficient to show conformance to all requi