ARMY SS-A-666 D-1968 ASPHALT PETROLEUM (BUILT - UP ROOFING WATERPROOFING AND DAMPPROOFING)《石油(防水防潮安装层面)沥青》.pdf

《ARMY SS-A-666 D-1968 ASPHALT PETROLEUM (BUILT - UP ROOFING WATERPROOFING AND DAMPPROOFING)《石油(防水防潮安装层面)沥青》.pdf》由会员分享，可在线阅读，更多相关《ARMY SS-A-666 D-1968 ASPHALT PETROLEUM (BUILT - UP ROOFING WATERPROOFING AND DAMPPROOFING)《石油(防水防潮安装层面)沥青》.pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、SS-A-666d SUPERSEDING Int . Fed, Spec, SS-A-00666c (MA-FSS) October 3, I968 and _. Fed. Spec. SS-A-666b October 16, 1968 MaVs- FEDERAL SPECIFICATION ASPHALT, PETROLFUM (BUILT-UP ROOFING, WATERPROOFING, AND DAMPPROOFING) This specification was approved by the Commissioner, Federal supply Service, Gen

2、eral Services Administration, for the use of all Federal agencies. 1. SCOPE AM) CLASSIFICATION 1.1 Scope, This specification covers petroleum asphalt for use as hot-cement and mopping coat in the construction of built-up roof coverings, in dampproofing, and in the construction of a membrane system o

3、f waterproofing. 1.2 Classification. 1.2.1 Asphalt shall be of the following types, as specified (see 6.2): Type I - For roofs with inclines not exceeding 1 inch per foot. II - For roofs with inclines between 1/2 and 3 inches per foot. III - For roofs with inclines between 1/2 and 6 inches per foot.

4、 IV - For roofs with relatively steep slopes and generally in areas with relatively V - Waterproofing, dampproofing, below ground level, at moderate temperature. VI - Waterproofing, dampproofing, above ground level, temperatures up to 125OF. VI1 - Waterproofing, dampproofing, above ground level, ver

5、tical surfaces, above 1259. high temperatures. 2. APPLICABLE DOCUMENTS 2.1 Specifications and standards. The following specifications and standardlof the issues in effect on date of invitation for bids or request for proposal, from a part of this slecification to the extent specified herein: Federal

6、 Soecificationa! PPP-D-705 - Drum: PPP-D-711 - Drum,:. PPP-D-723 - Drums, Fiber. Federal Standard: Fed, SM. No. 123 - Marking for Domestic Shipment (Civilian Agencies). (Activities outside the Federal Government may obtain copies of Federal Specifications , Standards, and Handbooks as outlined under

7、 General Information in the Index of Federal Specifications and Standards and at the prices indicated in the Index. issued, is for sale on a subscription basis by the Superintendent of Documents, U. s. Government Print- ing Office, Washington, D. C. 20402. (Single copies of this specification and ot

8、her product specifications required by activities outside the Federal Government for bidding purposes are available without charge at the General Services Admin- istration Regional Offices in Boston, New York, Washington, D.C. , Atlanta, Chicago, Kansas City, Mo. , Fort Worth, Denver, San Francisco,

9、 Los Angeles, and Seattle, Wash. Metal Shipping, Steel, (Over 12 and Under 55 Gallon) Metal, Shipping, Steel, Lightweight (55 Gallon). The Index, which includes cumulative monthly supplements as (Federal Government activities my obtain copies of Federal Specifications , Standards, and Handbooks and

10、the Index of Federal Specifications and Standards from established distribution points in their agencies. ) Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-1 SS-A-bbbD 5b m 7777374 0035328 4 m SS-A-666d Militam Standard: MIL-STD-129 - Marking for Shi

11、pment and Storage. (Copies of Military Specifications and Standards required by contractors in connection with specific procurement functions should be obtained from the procuring activity or as directed by the contracting officer .) 2.2 Other publications. specified herein. quest for proposal shall

12、 apply. The following docments form a part of this specification to the extent Unless otherwise indicated, the issue in effect on date of invitation for bids or re- American Society for Testing and Materiais (AsTM) Standards: D3l2 - Specification for Asphalt for Use in Constructing Built-up Roof Cov

13、erings. D449 - Specification for Asphalt for Danpproofing and Waterproofing. (Application for copies should be addressed to the American Society for Testing and Materials, 1916 Race St., Philadelphia, Pa. 191 03, ) American Trucking Associations, Inc; National Motor Freight Classification Rules. (Ap

14、plication for copies should be addressed to the American Trucking Association, Inc., 1616 P St., N,W., Washington, D.C. 20036.) Uniform Classification Committee: Uniform Freight Classificat$on Rules. (Application for copies should be addressed to the Uniform Classification committee, 202 Union Stat-

15、 ion, 516 W. Jackson Blvd., Chicago, Ill. 60606.) (Technical society and technical association specifications and standards are generally available for They are also distributed among technical groups and using Federal agencies .) reference from libraries, 3. REQUIREMENTS 3.1 Types I, II, III, and I

16、V, Each of these types shall meet the applicable requirements of ASTM D312. 3.2 Types V, VI, and VII. 4, QUALITY ASSURANCE PROVISIONS 4.1 Each of these types shall meet the applicable requirements of ASTM 04.49. Responsibility for inspection. Unless otherwise specified in the contract or purchase or

17、der, the supplier is responsible for the performance of all inspection requirements as specified herein. as otherwise specified, the supplier my utilize his own facilities or any commercial laboratory accept- able to the Government. in the specification where such inspections are deemed necessary to

18、 assure that supplies and services conform to prescribed requirements. with ASTM D312; for types V, VI, and VI1 sampling and testing shall be in accordance with ASTM 0449. Except The Government reserves the right to perform any of the inspections set forth 4.2 Sampling and testing. Sam3ling and test

19、ing, for types I, II, II1,and IV shall be in accordance 4.3 Inspection of preparation for delivery. The packing and marking of the asphalt shall be inspec- ted to determine conformance to the applicable requirements of section 5. 5. PREPARATION FOR DELIVERY 5.1 5.1 .I Packing. Packing shall be level

20、 A, B, or C as specified (see 6.2). Levels A and B. The asphalt shall be packed in quantities as specified (see 6.2), in a close- fitting fiber drum conforming to PPP-D-723, type I or II, grade C, as applicable. , Provided by IHSNot for ResaleNo reproduction or networking permitted without license f

21、rom IHS-,-,-SS-A-666d 5.1.1.1 Tmes I and II. Unless otherwise specified, the asphalt shall be packed in quantities as specified (see 6.2), in a close-fitting metal drum conforming to PPP-D-705, and PPP-D-711, type I, as applicable. 5.1.2 Level C, The asphalt shall be packed to insure carrier accepta

22、nce and safe delivery to des- tination at lowest rates. Rules. Containers and packing shall comply with Uniform Freight Classification 5.2 Marking. 5.2.1 agencies. In addition to markings required by the contract or order, the shipping con- tainers shall be mrked in accordance with Fed. SM, No. 123.

23、 5.2.2 Militarv agencies, In addition to markings required by the contract or order, the shipping containers shall be marked in accordance with MILSTD-129. 6. NOTES 6.1 Intended use. The suggested use for each type is not absolute, and overlapping of fields of use may occur between adjoining types,

24、depending upon the kind and occupancy of the buildihg involved; the kind of roof employed; the presence, absence, or thickness of any insulation; the specific material and construction used in the roofing membrane itself; and the temperatures and other climatic conditions to which the roofing may be

25、 subjected in service. Type I - Suitable for use on roofs with inclines up to 1 inch per foot. Type II - Suitable for use on roofs with inclines from 1/2 up to 3 inches per foot. Type III - Suitable for use on inclines from 1/2 to 6 inches per foot. Type IV - Suitable for use on roofs with relativel

26、y steep slopes and generally in areas with Type V - Suitable for use below ground level moderate temperature conditions both during the me VI - Suitable for use above ground level where not exposed to temperatures exceeding 1259. Type VI1 - Suitable for use above ground level, where exposed on verti

27、cal surfaces in direct sun- relatively high temperatures. process of installation and service. (52OC.) light or at a temperature above 125OF. (52OC.I. 6.2 Ordering data, Purchasers should select the preferred options permitted herein and include the following information in procurement documents: (a

28、) Lb) (c) Title, number, and date of this specification! “ype of asphalt required (see 1.2.1). Slection f applicable level of packing required (see 5.1). 6.3 Asphalt for dampproofing and waterproofing, types V, VI, and VI1 in this specification correspond respectively to types A, B, and C in ASTM 04

29、49. MILITARY CUSTODIANS: Army - ME Navy - M) Air Force - 84 User activities: Army - None Navy - CG, MC Air Force - None Review Activities: Preparing activity: Army - ME Navy - PD Air Force - 84 MA-FSS *U, S. GOVEXNblENT PRINTING OFFICE: 1968 O - 302-612 (7128) Orders for this publication are to be p

30、laced with General Services Administration, acting as an agent for the Superintendent of Documents. other documents referenced herein. Price 6 cents each. See section 2 of this specification to obtain extra copies and 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-