ARMY MIL-W-63377-1987 WARHEAD ILLUMINATING M257 W M442 FUZE (2 75 INCH ROCKET ILLUMINATING FLARE)《M257型W M442引信(2 75英寸火箭照明闪光)照明弹头》.pdf

《ARMY MIL-W-63377-1987 WARHEAD ILLUMINATING M257 W M442 FUZE (2 75 INCH ROCKET ILLUMINATING FLARE)《M257型W M442引信(2 75英寸火箭照明闪光)照明弹头》.pdf》由会员分享，可在线阅读，更多相关《ARMY MIL-W-63377-1987 WARHEAD ILLUMINATING M257 W M442 FUZE (2 75 INCH ROCKET ILLUMINATING FLARE)《M257型W M442引信(2 75英寸火箭照明闪光)照明弹头》.pdf（66页珍藏版）》请在麦多课文档分享上搜索。

1、g a., z( MIL-W-63377 (AR) 29 April 1987 MILITARY SPICIFICATION WARHEAD, ILLUMINATING, M257 , W/M442 FUZE (2.75INCH ROCKET ILLUMINATING FLARE) This specification is approved or use within the U.S. Army Armament, Munitions and Chemical Command, and is available for us by all Departments and Agencies o

2、f the Department of Defense, 1. SCOPE 1.1 Scope. This specification covers the quality assurance provisions and special requirements not covered by the drawings for one type of warhead designated as Warhead, 2.75 Inch Rocket Illuminating Flare, M257. 2. APPLICABLE DOCUNENTS 2.1 Government documents.

3、 2.1.1 Specification and standards. The following specifications and standards form a part of this specification to the extent specified herein. Unless otherwise specified, the issues of these documents shall be those listed in the issue of the Department of Defense Index of Specifications and Stand

4、ards (DODISS) and supplement thereto, cited in the solicitation. a SPEC1 F I CATIONS MILITARY MIL -A-, 3078 - Ammunition, Standard Qual ty Assurance Provisions, General Specification for M4 4 2 MIL -F - 7 O 6 73 - Fuze, Rocket, Base Detonating, Beneficial comments (recommendations, additions, deleti

5、ons) and any pertinent data which may be of use in Improving this document should be addressed to: Commander, U.S. Army Armament Munitions and Chemical Command, Ath AMSMC-QA, Picatinny Arsenal, New Jersey 07806-5000 by using the self-addressed Standardize- tion Document Improvement Proposal (DD Form

6、 1426) appearing at the end of this document or by letter. I AM: N/A FCC 1340 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. THIS DOCUMENT CONTAINS bh PAGES. Licensed by Information Handling ServicesMIL-W-63377 (AR) STANDARDS MIL-STD-10 5 - Sampling Procedures and

7、Tables MIL-STD-3 31 - Fuze and Fuze Components, for Inspection by Attributes Environment al and Per f ormance Tests for MIL-STD-414 Sampling Procedures and Tables for Inspection by Variables for Percent Defective MIL-STD-4 53 I nspec t ion , Radiographic MIL-STD-810 - Environmental Test Methods 2.1.

8、2 Other Government documents, drawings and publications. The following other Government documents, drawings and publications form a part of this specificaiion to the extent specified herein. Unless otherwise specified, the issues shall be those in effect on the date of the solicitation. DRA WINGS US

9、 ARMY ARMAMENT, RESEARCH, DEVELOPMENT, AND ENGINEERING CENTER (ARDEC) 8883479 - 9298733 - 9340646 - 9347035 - 9294519 - 9394492 - 9340647 Y Warhead, 2.75 Inch Rocket Flare, *M257 Cont, Ammo, Fiber, M518, for rocket Motor: 2.75 Inch, Mark 40 Mods, and Mark 4 and Mods Box Packing Ammo for Rocket Motor

10、, 2.75 Inch, Mark 40 and Mods, Mark 4 and Mods Fuze, Rocket, Base Detonating, M442 BOX, Fiber , Packing, Ammunition for Warhead, 2.75 Inch Rocket Flare, M257 Packing and Marking for Box, Wood, Wirebound Pallet Type , for Warhead 2.75 Inch Rocket Illuminating M257 Packing and Marking for Container, A

11、mmunition, Fiber , M518 for Warhead 2.75 Inch Rocket Flare, M257 only Packing and Marking for Box, Wood Packing Ammunition for Wrahead, 2.75 Inch Rocket Flare M257, Rocket Motor: 2.75 Inch, MK40 and Mods and MK4 and Mods Pallet, (Boxed Type) , for Warhead, 2.75 Inch Rocket: Illumination, M257 2 Lice

12、nsed by Information Handling ServicesMIL-W-63377 13 m 7777906 0347287 7 m MIL-W-63377 (AR) 9357963 - Box Packing Ammo for Rocket Motor, 2.75 Inch, MK66 12624792 - ,Packing and Marking for Box, Wood Packing Ammunition for Warhead, 2.75 Inch Rocket Flare M257, Rocket Motor: 2.75 Inch, MK66 19-48-4116/

13、80M - Unitization Procedures for Boxed Ammunition and Components on 4-Way Entry Pallets (Copies of specifications, standards, handbooks, and publications required by manufacturers in connection with specific acquisition functions should be obtained from the contracting activity or as directed by the

14、 contracting activity.) 2.1.3 Order of precedence. In the event of a conflict between the text of this specification and the references cited herein (except for associated detail specifications, specification sheets or MS standards), the text of this specification shall take precedence. Nothing in t

15、his specification, however, shall supersede applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Material. Materials shall be in accordance with the applicable drawings and specifications. 3.2 Components and assemblies. The components and assemblies shal

16、l comply with al1 requirements specified on Drawing 9332220 and associated drawings and with all requirements specified in applicable specifications and standards. 3.3 Metal and plastic defects. All of the components prior to painting or chemical treatment shall be free of surface imperfections on t

17、he interior and exterior surfaces of the part which are indications of discontinuities internal to the material. (Included are cracks, lube bursts, pipes, laminations, segregations, porosity, air holes, flakes, inclusions, and other in.terna1 defects.) 3.4 Ballistic test. - The completely assembled

18、round (warhead either with MK40 motor or MK66 motor) shall be ballistically tested to comply with the following requirements: 3.4.1 Function time. The time between rocket motor ignition and flare candle ignition shall be 13.5 + 2.0 seconds with MK40 motor and 13 + 2.0 seconds with MK66 motor. 3 Lice

19、nsed by Information Handling ServicesMIL-W-63377 L3T 7777906 O?KZTOT MIL-W-63377 (AR) 3.4.2 Descent characteristic. The burning flare shall descend on the parachute for a minimum of 90.0 seconds, after ignition and before ground contact. 3.4.3 Flare burn time. The flare candle shall burn for a minim

20、um of 100 seconds. Burn time upon ground impact may be included. 3.5 Illumination. The flare candle shall produce an average light output of 1 million candle power or a minimum of 95 seconds. 3.6 Rough handlinq. The warhead shall withstand rough handling when tested as specified in 4.5.2 and shall b

21、e safe to handle, fire, and dispose of. Warheads that are suitable to fire shall be assembled to rocket motors which have not been subjected to rough handling environments prior to firing. Firing of warheads shall be for informational purposes only. 3.7 Tempoature. The warhead shall withstand exposu

22、re to a storage temperature of +14OoF + 5OF, -25OF + 5O, and 70OF t 5OF for 8 hours minimum-and shall comply with the ballistic test as specified in 4.5.13. 3.8 Secured carqo vibration. The warhead shall withstand exposure to secured cargo vibration as specified in 4.5.3 and shall comply with the ba

23、llistic test as specified in 4.5.13. 3.9 - Helicopter vibration. The warhead shall withstand exposure to helicopter vibration as specified in 4.5.4 and shall comply with the ballistic test as specified in 4.5.13. subjected to and must withstand the Forty-foot Drop Test as specified in MIL-STD-331. 3

24、.10 Warhead forty-foot drop test. The warhead shall be 3.11 Warhead leak test. The warhead shall not leak when subjected to the leakage test as specified in 4.5.6. 3.12 Radiographic quality. X-rays shall be taken in accordance with MIL-STD-453 and shall be OE a quality which will permit proper evalu

25、ation as determined by the responsible technical agency of the Government. Minimum optical density of each radiograph in the area being inspected shall not be less than 1.25 and shall be within a density range that will permit proper identification of defects. 3.13 - Functional straiqhtnee. Each war

26、head when attached to a dummy rocket motor shall be capable of passing through a gage 50.100 + 0.25 inches long, 2.7952 + .O020 inches in diameter, and straight within .O020 inches total. 4 Licensed by Information Handling ServicesMIL -w- 6 3 3 7 7 ( AR) 3.14 Gas generator non-f unction test. The ga

27、s generator shall not function when a static extraction force of 20 pounds is - applied to the sear. . 3.15 Gas generator and expulsion charqe function test. The gas generator shall function and ignite the expulsion charge when tested as specified in this specification. The requirement for time dela

28、y is indicated on dwg. 9332277 3.16 M442 Fuze. All M442 fuzes shall have been subjected to and pass all the requirements of MIL-F-70673(AR). 3.17 Iqniter assembly function test. The armed igniter assembly shall function upon application of force of 50 pounds minimum and 75 pounds maximum upon the ca

29、ble. The boron-pellets shall be fully consumed. 3.18 Ziq-zag setback mechanism assembly non-arming test. The zig-zag setback mechanism assembly shall remain in the non-armed and safe condition after being subjected to an acceleration force of sixteen (16) gs plus or minus .5 gs for a duration of thr

30、ee (3) seconds min. 3.19 Zig-zaq setback mechanism assembly arminq test. The zig-zag setback mechanism assembly shall arm when subjected to an acceleration force of twenty-two (22) gs plus or minus .5 4s for a duration of one (1) second maximim. 3.20 Ziq-zaq setback mechanism assembly reset capabili

31、ty test. The setback weight shall be capable of returning to the unarmed position on its-own after it has been partially-armed. 3.21 First article inspection. This specification contains technical provisions for first article inspection. Requirements for thesubmission of first article samples by the

32、 contractor shall be as specified in the contract. 3.22 Workmanship. The components and assemblies shall be fabricated and finished in a thorough, workmanlike manner. They shall be free of burrs, sharp edges, unblended radii, dirt, grease, rust, corrosion products and other foreign matter. The 5 Lic

33、ensed by Information Handling ServicesMIL-W-63377 (AR) cleaning method used shall not be injurious to any part nor shall the parts be contaminated by the cleaning agent. Surface coatings shall be continuous except for a few slight scratches not exposing base material. All required markings shall be

34、neat and legible. 4. QUALITY ASSURANCE PROVISIONS 4.1 Responsibility for - inspection. Unless otherwise specified in the contract, the contractor is responsible for the performance of all inspection requirements as specified herein. Except as otherwise specified in the contract, the contractor may u

35、se his own or any other facilities suitable for performance of the inspection requirements specified herein, unless disapproved by the Government. The Government reserves the right to perform any of the inspections set forth in the specification where such inspections are deemed necessary to assure.

36、 supplies and services conform to prescribed requirements Unless otherwise specified herein or in the contract, the provisions of MIL-A-48078 shall apply and are made a part of this specification. 4.1.1 Responsibility for compliance. All items must meet all requirements of-sections 3 and 5. The insp

37、ection set forth in this specification shall become a part of the contractors overall inspection system or quality program. The absence of any inspection requirements in the specification shall not relieve the contractor of the responsibility of assuring that al1 products +or supplies submitted to t

38、he Government for acceptance comply with ail requirements of the contract. Sampling in quality conformance does not authorize submission of known defective material, either indicated or actual, nor does it commit the Government to acceptance of defective material. 4.2 -I Classification of inspection

39、s. The following types of inspection shall be conducted on this item: a. First Article Inspection b. Quality Conformance Inspection 4.3 First article inspection. 4.3.1 Submission. The contractor shall submit a first article sample as designated by the Contracting Officer for evaluation in accordame

40、with provisions of 4.3.2. The first article sample shall consist of the following items in sample quantities as indicated. 6 Licensed by Information Handling ServicesMIL-W-63377 13 = 9999906 03LI9291 O MIL-W-63377 (AR) Part Description Cap, Retainer Closure Spring, Striker Arm, Striker Pin, Firing S

41、lider Mechanism Assembly, Setback -Zig-Zag Pin, Shear Cushion Wafer, ignition Assembly, Igniter Raceway Assembly, Charge Ca se Case Assembly Case Assembly, Insulated Case Assembly, Tack Coated Gas Generator Case Assembly, Loaded Candle and Parachute Assembly Parachute, Main Container, Deployment Par

42、achute Assembly Insert, Main Parachute Fitting and Cable Assembly Separation and Drogue Release Parachute, Drogue Housing, Drogue Chute Drogue and Housing Assembly Adapter, Motor Adapter Assembly, Motor Motor Adapter m arararararararar I tntntnotnotntn m mmmmmmmm .rl wwwwwwww 3 hl CJ CJCJCJCJCJCJCJC

43、J .o . mmmmmqmm m u al rl U al a al 4 3a O a u w O Licensed by Information Handling ServicesI l (u 8 rl E 5 a, 2 8 rl u -_ - MIL-U-63377 I3 W 7779706 0347302 I U I -. (um W(u(u(ucJ(u(uN(u(u(u (u MM MMMmmMmMmmM m . . 5 s .d c u4 a, 5 a, c O z 18 c I2 W cr L3 c3 Licensed by Information Handling Servic

44、es5 MIL-W-63377 13 m 7777906 031.17303 3 m a, Y 8 rl L) - E = x E $ W ZL W a L W u I a. a a z 4. f W 5 - rl Id 7 m .rl 3 . m Licensed by Information Handling ServicesMIL-W-63377 13 = 9999906 03-4= a a, c .rl w a, W a, c O 2 8 O Liu a u cn a, c, a, 7 bl h ci cui uu ici 20 Licensed by Information Hand

45、ling Services8 K u a, ci c tn H -4 h tn c -4 o 1 O m I w rl a tntntntntntna u o u II) Li oArl a, cid a,Q)oa,oa,ooo a COQ tntntnu Li Li a, uJJ pici aci acF: 21 Licensed by Information Handling ServicesLI a, ci rl H w h tn c .rl 2 O X * I,. * CJ CJ CJCJCJCJCJ CJCJCJ m mmmmm mmm . .e. . o. . n Id O rl

46、Y cs rl v .u u a, -n !2 n O Y ci (I a, u 2 e ci O rl u a, (I O rl 1; v 7 F n O b Li E O Li Licensed by Information Handling ServicesY n 8 nl CICVC*IC*INC*I C*I mmmmmm m . III a, 5 .rl III pi .rl c III c a E 24 3 w O O pi 4-1 O a, u d a, 5 .rl 3 w 8 rl 031 23 Licensed by Information Handling Services

47、_ _- MIL-W-63377 13 7777706 0347308 2 a _ tn c .d L! .FI Fr c PI . .d rl hl NCJN CVCJCJCJCJ mmm mmmmm . .o. SC c Id c O O ci c a u-l O .FI .u I n L! c3 aJ LI n n O h LC I- L - O 24 Licensed by Information Handling Servicesc MIL-W-63377 13 7997906 0347307 Li r*) (u(u (u MM M . al c O z a 0 cn pi 3r r

48、l u c -4 al o) pi c O u a SC z Ii JJ om 3 cc .A Li uu om o) om O0 rld al E .;i E- u0 QV - O O pi w O al u c al a .FI w 25 R B Licensed by Information Handling ServicesMIL-W-63377 23 7977706 03Ll73Lfix CJ c.1CJCJCJCJCJ CJCJCJCJ CJCJ mmmmmm mmmm mm *e .o u a, W .rl ri cn Z E ci ci O a O 5, c ci W .A 5

49、 cih %I: .d 5 b a,+ ia c3u c ala, rlW a -rl a3 uw il 26 Licensed by Information Handling Servicestr, Id N I tn .FI N I .Y u Id a ci a, cn 3.i ri a (o 4 $ 2 5l % 1 .FI c Id o30 m m 4“ CJ“CJr( NCICJ . . . mmm mmmmm mmm Id a Id u ci a, 5 rl Id u .rl ci .rl LI L) rlrum-Fm 00000 rlrlrlrlrl .FI 81 c rlmm O00 mcIcI 27 Licensed by Information Handling Servicesd 8 rl 8 rl O rl c*l -I- * . . - ri rd Cu NN N mm m . 5 0) Li C aJ (u c O 2 a .FI c O C m E 24 3 Li O O a w O aJ u c 8 28 . c Licensed by Information Handling Services-_ -_ MIL-W-63377 13 9749906 03q7313