ARMY MIL-W-63150 (3)-1988 WEAPONS AND SUPPORT MATERIEL STANDARD QUALITY ASSURANCE PROVISIONS FOR《武器和支援军品标准质量规定》.pdf

《ARMY MIL-W-63150 (3)-1988 WEAPONS AND SUPPORT MATERIEL STANDARD QUALITY ASSURANCE PROVISIONS FOR《武器和支援军品标准质量规定》.pdf》由会员分享，可在线阅读，更多相关《ARMY MIL-W-63150 (3)-1988 WEAPONS AND SUPPORT MATERIEL STANDARD QUALITY ASSURANCE PROVISIONS FOR《武器和支援军品标准质量规定》.pdf（4页珍藏版）》请在麦多课文档分享上搜索。

1、MIL-w-63150 (AR)AMENDMENT 09 September1988SUPERSEDINGAMENDHENT 230 September 1987“(seeMILITARY SPECIFICATIONWEAPONS AND SUPPORT MATERIELSTANDARD QUALITY ASSURANCE PROVISIONSSection 6)FORThis amendment forms a part of Military Specification MIL-W-63150 (AR), dated 1 August 1977, andis approved foK us

2、e withinU.S.Army Armament, Munitions and Chemical Command, and is ,.available for use by all Departments and Agencies of theDepartment of,Defense.“PAGE12.1, SPECIFICATIONS, MILITARY: Delete references toMIL-C-6Ei2l,MIL-R-11468, MIL-R-11469 and MIL-M-11473 in their entirety.PAGE 22.1, SPECIFICATIONS,

3、 MILITARY: .-.-Delete reference to MIU-C-45662 in its entirety.*“ Add the following: MIL-A-70625 (Fdistributioniski.mited.-:”:-.LProvided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-w-63150 (AR)IIAMENDMENT 3PAGE 32.2, Other publications:Delete ANSI Y3

4、2.3 in its entirety and substitute: “ANSI/AWSA2.4 - Standard Svmbols for weldinq, Brazinq and Nondestructive.Examination.” -Deiete reference to ASTM E16 and ASTM E99 in their entirety.Add the following reference:“ASTM-E125 - Photograph, ReferenceIndications on Ferrous Castings”PAGE 9for Magnetic Par

5、ticle* 3.6.4, Add the following sentence at the end of this paragraph:“Inspections for protective coating shall be as specified3.6.7.”PAGE 103.6.6.f: Delete in its entirety and substitute new “f” asfollows:-.“f. Where a drawina number is sified as the inspectionmethod in the specifiction, SQAP, iecD

6、ata Package list orEquipment List, a Government-approved acceptance inspectiondesign is available and the contractor shall use inspectionequipment fabricated in accordance with the reference design.PAGE 11inInsert new paragraph 3.6.6.i to follow paragraph 3.6.6.hasfollows: “.“i. Where Gage is specif

7、ied as the inspection method andno Government-approved acceptance inspection design is avail-able, the contractor shall use SMTE (See 3.6.6.e).“* Add the following to paragraph 3,6.7:“These inspections shall be classed as major characteristics, foracceptance purposes, unless otherwise specified in t

8、he itemspecification or SQAP.”PAGE 13 ,3.7.3, line 3: Delete “or MIL-”sTD-1263.”,.,.,Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-w-63150 (AR), AMENDMENT 33.7.4,Line 5: Delete “E16, E99.”Line 7: Delete “ANSI Y32.3 and subst3.7.5,tute ANSI/AWS

9、A2.4.”Line 4: Delete “MIL-C-6021, MIL-R-11468.,MIL-R-11469.”Line 4: Change MIL-P-45774” to “MIL-R-45774.”Line 5: Delete “E99.”PAGE 17 .3.7.14.5: Delete the last sentence, Soldering.l46k”.”and substitute a new sentence as follows:“Unless otherwise specified on the drawing or in the itemspecificationj

10、”soldering shall be in accordance.with MIL-STD-1460.” .* 3.8.1Para c: Add the following sentence to the end of theparagraph on page 18.In addition to the requirements as specified in thisspecification and in the applicable contract, the requirementsof MIL-A-70625 shall apply to autom acceptance insp

11、ectionequipment.”PAGE 183.8.l.f, line 3: Change “MIL-c-45662” to “MIL-sTD-45662.”Add new paragraphs as follows:6.4 m (kev word) llsq,.CertificationIn-process controlInspection, Test6.5 dedxiin its entirety.”:i:. . .I .MIL-w-63150 supersedes MIL-Q-45970A,3Provided by IHSNot for ResaleNo reproduction

12、or networking permitted without license from IHS-,-,-MIL-w-63150 (AR)AMENDMENT 3 .:“The margins of this amendment are marked with an asterisk Orvertical lines to indicate where changes (additions,modifications, corrections, deletions) from the previous amend-ment were made. This was done as a conven

13、ience only and theGovernment assumes no liability whatsoever for any inaccuraciesin these notations. Bidders and contractors are cautioned toevaluate the requirements of this document based on the entirecontent irrespective of the marginal notations and relationshipto.the last previous amendment.”Custodian: Preparing Activity:Army-AR Army-AR(Project 10GP-A0137). -_.=:. -. 4Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-