ARMY MIL-W-11446 A-1957 WATCHES AND STOP WATCHES PACKAGING OF《监装和阻装》.pdf

《ARMY MIL-W-11446 A-1957 WATCHES AND STOP WATCHES PACKAGING OF《监装和阻装》.pdf》由会员分享，可在线阅读，更多相关《ARMY MIL-W-11446 A-1957 WATCHES AND STOP WATCHES PACKAGING OF《监装和阻装》.pdf（9页珍藏版）》请在麦多课文档分享上搜索。

1、MIL-W-LLq46A 66 9999906 0227960 3 29 Nor. enb er -395 7 SUPERSEDING MIL-P-l1446(Ord) 13 September I951 MILITARY SPECIFICATION WATCHES AND STOP WATCHES: PACKAGING OF 1. SCOPE 1.1 This specification covers the packaging and packing of navigation watches, pocket watches, wrist watches and stop watches

2、for each level of protection. 2. APPLICABLE DOCUMENTS 2.1 The following documents, of the issue in effect on date of invitation for bids, form a part of this specification: SPECIFICATIONS Federal UU-T-106 UU-T -1 1 1 PPP-B-585 PPP -B -60 1 PPP-B -621 PPP-B-636 PPP-B-676 PPP- C-843 PPP-T -76 Tape, Ma

3、sking: Paper (Pressure -Sensitive) Tape: Paper, Gummed (Sealing and Securing) Boxes; Wood, Wirebound Boxes; Wood, Cleated-Plywo3d Boxes, Wood, Nailed and Lock-Corner Boxes, Fiber Boxes, Set-up, Paperboard Cushioning Mate rial, Cellulosic Tape, Pressure -Sensitive Adhesive, Paper, Water Resistant Mil

4、itary MIL-P-116 - Preservation, Methods of MIL-B-117 - Bags, interior Packaging MIL-B-131 - Barrier Material; Water VapOrprObf, Flexible A Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-Street, N. W., Washington 6, D. C.) 3, REQUIREMENTS 3.1 Materia

5、ls and methods. - The materials, methods and procedures used in the packaging of items shall be in accordance with this specification. Materiale and methods not covered by a specification shall be suited to the intended uee and subject to the approval af the cmtracting officer. Unless Provided by IH

6、SNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-otherwise ipecified, the contractor shall provide the Government inepector 1 certification of adherence to the required material specifications, 3.2 Size of containers. - Bage, interior containers and exterior con- I

7、 tainers shall be of a minimum size to adeauatelv contain the items. 3.3.1 LevelA 3.3.1 e 1 Cleaning. - The exterior surfaces shall be cleaned 80 as to be free from dirt, smudges, fingerprints and other foreign substance6 in accerd- ance with method C-1 of Specification MIL-P-116. I 3.3.1.2 Drying.

8、- Immediately after cleaning, items shall be dried thoroughly in accordance with any procedure specified in Specification MIL- I P-116 that will not damage the items. 1 Specification MIL-P-116 as described herein QF method U using a spirally wound fiber tube container . The rubber shock absorber and

9、 leather chain I shall be packaged method IC-3 of Specification MIL-P-116 as described herein. 1 thicknesses of neutral tissue conforming to Specification MIL-P-13988 and overwrapped with cellulosic cushioning material (at least 1 /4 inch thick) con- f3rming to type U, any class of Specification PPP

10、-C-843. The wrap shall be secured with pressure sensitive tape conforming to type I of Specification UU- T-106. around the watch prior to wrapping the watch with the neutral tissue and cush- ioning material. When a wrist watch is involved, the wrist strap shall be wrapped 3.3.1.3.2 Desiccant. - The

11、required units of disiccant conforming to I Snecification MLL-D-3444 shall be secured to the cushioned watch with ree- sure sensitive tape conforming to the tape specified in 3.3. l. 3. l. The re- quired mits of desiccant to be secured shall be determined by Formula I of I SDecification MIL-P-i 16.

12、1 cant attached shall be placed in a water-vaporproof bag fabricated from barrier- material conforming to class 2 of Specification MIL-B-131. heat sealed in such a manner as to pase the heat seal and quick leak tests of Specification MLL4-P-116. Air shall be exhausted from the bag prior to final clo

13、sare. The bag shall be I 3. I Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-I I MIL-U-1144bA bb 9?777906 0127963 7 L .?41L-W -1 1446A(Ord) I leather chain accompany a pocket or stop watch, the chain shall be zolled up and placed inside the shock ab

14、sorber. in a bag conforming to type LLI, class b of Specification MIL-B-117. shall be heat sealed in such a manner as to pass the waterproofness test of Specification MIL-P-116. 4 The shock absorber shall then be placed I The bag Air shall be exhausted from the bag prior to final I 1 ed in a set-up

15、paperboard box conforming to type I or IV, any class and style of Specification PPP-B -676. When a shock absorber and chain accompany a watch the bagged watch and the bagged shock absorber and chain shall be placed to- gether in the set -up paperboard box. The box shall be closed by covering all sea

16、ms with gummed tape conforming to class I of Specification UU-T-111. 3.3.1.3.6 Spirally wound fiber container. - A spirally wound fiber containe conforming to type J., grade B, style a, class I of Specification MIL-C-3955 can be used in lieu of the water-vaporproof bag and Set-up paperboard box spec

17、ified in 3.3.1.3.3 and 3.3.1.3.5. watch shall be cushioned as specified in 3.3.1.3.1 and the required units of desiccant to be immobilized in the container with the cushioned watch shall be as specified in 3.3.1 3.2, When a rubber shock absorber and leather chain ac campany a watch, the shijck absor

18、ber and chain shall be bagged as specified in 3.3.1.3.4 and the bag shall then be imrnDbilized in the container with the cush- ioned watch and desiccant. The spirally waund fiber container shall be machin closed in such a manner as to pass the quick leak test of Specification MIL-P-1 If the spirally

19、 wound fiber container is used, the e I 3.3.1.3.7 Intermediate packaging. - Ten unit packaged watches (watches oi immobilized in a fiberboard box conforming to compliance symbol W5s or W5c and any style, except FTC B? Specification PPP-B-636, class 2, Each fiber- board box shall be closed by applyin

20、g water -resistant pressure -sensitive tape at least two inches wide conforming to Specification PPP-T-76 over all seams including the manufacturer?s jJint. 3.3.2 Level B 3- 3.2-1 Cleaning and?drvine. - Cleaning and drying shall be as specified P-116, cant shall be omitted. Unit packaging shall be a

21、s specified in 3.3.1.3, except that the desic- I ? -7, I Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-5. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-and omitteu on the Level C shipping containe

22、r. 3.5.3 Stock number. - The stock number to be added in the identification data shall be obtained from the contracting officer. 3.5.4 SpeciaI marking. - 3.5.4.1 Level of protectinn. - Shipping containers containing watches packaged for eve B or C protection, shall be conspicuousIy marked LTD MIL PK

23、G or MIN MIL PKG, as applicable. 3.5.5 Protecting oversea exterior container markings, - All oversea exterior cDntainer markings shali be protected with waterproofing material as specified in Standar MIL-STD-129. 36 Pilot pack. - Prior to- quantity production, a preproduction pack, consisting of a c

24、omplete and packed shipping container, shall be slibmitted to the Government inspector to determine conformance with the appiic.;.cbI.e re - quiremens of this specification for Levels A and B. 3,7 Workmanship. - Adequate controIs shall be utilized to check for c ,n - tamination of cleaning solvens.

25、Wraps shail be neat, canforming anci fir11 .i-: secured. Inadequate and excessive dunnage shall be avoided. Tapes chiri: be uniformly applied to interior boxes and shall completely cover and adtic-. :- Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-

26、MIL-W -1 1446A(Ord) 4. QALITY ASSURANCE PROVISIONS 4.1 Inspection and tests. - The tests shall be accomplished by the con- .ractor or his agent under surveillance of the Government inspector. ;ion and test procedures shall be conducted in process. Inspec- I 4.2 Lot sizes. -The lot size submitted for

27、 acceptance purposes shall be ible, consistent with available facilities. 4.3 Sampling I 4.3.1 For insDection. - Sampling or inspection shall be conducte% in ac- cordance with inspection level I of Standard YL-STD -1 05. I 4.3.2 For tests. - Sampling for tests for packages shall be conducted in I ac

28、cordance with Table I. 3 to 50 51 to 500 501 o 1000 1001 and over I =3 5 10 15 1 1 2 3 4-4.1 Classification of defects, - VisuaI inspection for defects estab- lished in Table II or exterior containers. 1 TABLE If - CLASSIFICATION OF DEFECTS Categories and defects AQL (%I Maior I Illegible marking I

29、1 hcor r e ct marking .l.O 1.0 Improper cl3sure of interior packages Improper packing (container owrsize; inadequate or Noh-adherence to the requirements of prescribed ship- 2.5 excessive cushioning material; etc. ) . , 2.5 ping container specificafion 2.5 7. r Provided by IHSNot for ResaleNo reprod

30、uction or networking permitted without license from IHS-,-,-Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-, MIL-W-LLq4bA 66 W 7799706 0327768 m MIL-W -1 1446A(Ord) f 6.3 Replacement of packaging materials. - The procurement documents should specify

31、 that all packaging materials and containers whish become un - serviceable during inspection and teste Elhall be replaced prior to shipment of the items. NOTICE: When Government drawings, specifications, or other data are used for any purpose other than in connection with a definitely related Covern

32、ment procurement operation, the United States Government thereby incurs no re - apmsibility nor any obligation whatsoever; and the fact that the Government may have formulated, furnished, or in any way supplied the said drawings, specifi- cations, or other data, is not to be regarded by implication

33、or otherwise as in any manner licensing the holder or any other person or corporation or convey- ing any rights or permission to manufacture, use or sell any patented invention that may in any way be related thereto. Cuet odian: v Preparing Activity: L; Army - Ordnance Corps Other interest: Army - Ordnance Corps Q R I 9. Q f Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-