ARMY MIL-V-48190-1972 VENT ASSEMBLY《排气(通风)道总成》.pdf

《ARMY MIL-V-48190-1972 VENT ASSEMBLY《排气(通风)道总成》.pdf》由会员分享，可在线阅读，更多相关《ARMY MIL-V-48190-1972 VENT ASSEMBLY《排气(通风)道总成》.pdf（9页珍藏版）》请在麦多课文档分享上搜索。

1、4 MIL-V-48190 11 m 9999906 0467877 6 m MIL-V-48190 (MU) 6 September 1972 MILITARY SPECIFICATION VENT ASSEIIIBLY 1. SCOPE . 1.1 This specification covers requirements, quality assurance provisions, and the preparation for delivery cri- teria for one type of vent assembly used on M467 Container for XM

2、454 and 455 projectiles and containers in general. 2. APPLICABLE DOCUMENTS 2.1 The following documents, of the issue in effect on date of invitation for bids or request for proposals, form a part of this specification to the extent specified herein: SPECIFICATIONS MILITARY MIL-P-116 - Preservation,

3、Methods of STANDARDS MILITARY MIL-STD-105 - Sapling Procedures and Tables for Inspection by Attributes NIL-STD-1168 - Lot Numbering of Ammunition MIL-STD-l169(MU) - Packaging, Packing, and Marking for Shipments of Inert Ammunition Components MS 25043-1OC - Cap MS 35743-1 - Rivet, Solid, Pan Head MS

4、39081-4 - Nut Plain, Hex FSC-1190 1 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- MIL-V-48LSO LL = 9999906 0467878 8 W MIL-V-48190 (MU) DRAWINGS ORDNANCE CORPS 4 8808362 - Packing and Marking for Storage and Shipments 8853791 - Vent Assembly 88537

5、92 - Cap Assembly 8853794 - Retainer 8853797 - Gasket 8853798 - Washer 8883535 - Bag, Packing, for Repair Parts ET-8853791 - Equipment Tabulation 8853795 - Plug (Copies of specifications, standards, drawings, and publica- tions required by suppliers in connection with specific procurement functions

6、should be obtained from the procuring activity or as directed by the contracting officer.) 3. REQUIREMENTS 3.1 Materials. The contractor shall furnish objective evidence (see 6.2) that the material complies with the speci- fications listed on the applicable drawing. 3.2 Assembly. The vent assembly s

7、hall comply with all requirements specified on the drawing (dwg) 8853791, with all requirements specified herein, and with the requirements of all applicable specifications to the extent specified on the drawing and herein. 3.3 Workmanship. 3.3.1 Plastic and metal characteristics. All compo- nents s

8、hall be free from cracks, splits, cold flow, shrinkage, cold shuts, inclusions, porosity, or any similar characteristic. 3.3.2 Threads. Threads shall be full and undamaged for the entire minimum length or depth as required on the applicable drawing. 3.3.3 Burrs. Parts shall be free from burrs. 3.3.4

9、 Foreign matter. Parts shall be free from-chips, dirt, grease, rust, corrosion, or any embedded foreign ma- terial. 3.3.5 Cleaning. The cleaning method shall not be in- jurious to any of the parts, nor shall the parts be contaminated by the cleaning agent. 2 Provided by IHSNot for ResaleNo reproduct

10、ion or networking permitted without license from IHS-,-,-MIL-V-48190 11 W 9999906 0467879 T W MIL-V-48190 (MU) 4. QUALITY ASSURANCE PROVISIONS 4.1 Responsibility for inspection. Unless otherwise specified in the contract-or purchase order, the supplier is responsible for the performance of all inspe

11、ction re- quirements as specified herein. Except as otherwise speci- fied in the contract or order, the supplier may use his own or any other facilities suitable for the performance of the inspection requirements specified herein, unless disapproved by the Government. The Government reserves the rig

12、ht to perform any of the inspections set forth in the specifica- tion where such inspections are deemed necessary to assure supplies and services conform to prescribed requirements. 4.2 First article inspection. Not applicable. 4.3 Quality conformance inspection. 4.3.1 Lot formation. 4.3.1.1 Product

13、ion lot. A lot shall consist of parts and assemblies produced by one manufacturer in one unchanged process, in accordance with the same drawing, same drawing revision, same specification and same specification revision. Drawing, specification and process changes not affecting safety, performance, st

14、orage, or interchangeability, as de- termined by the Government, shall not necessitate changing the lot interfix number. The criteria and procedures for the assignment of lot numbers shall be in accordance with MIL- STD-1168. 4.3.1.2 Inspection lot. A lot or batch and its forma- tion, size, and pres

15、entation is described in MIL-STD-105, Section 5. Accordingly, a lot shall mean an inspection lot and a batch shall mean an inspection batch for the purpose of this specification. The manner in which each inspection lot or batch is to be presented and identified by the con- tractor, shall be designat

16、ed or approved by the Government representative. - 4.3.2 Product inspection examination. Critical characteristics shall require 100 percent inspection of all items in the inspection lot. A sample shall be selected at random from each inspection lot in accordance with the ap- plicable major or minor

17、characteristic table (see Table I and Table II), and inspected for all characteristics in the applicable classification. Any characteristics in the sample found to be defective shall reject the inspection lot. Se- quence for the inspection of characteristics in each classi- fication need not be foll

18、owed as long as all characteristic inspections are performed. 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-V-48190 (MU) Table I Major Characteristics Sample Sample Sample Sample Lot Size Size Lot Size Size Lot Size Size Lot Size Size 1-16 al

19、 1 17 16 18 17 19-20 18 21 19 22-23 20 24-25 21 26-27 22 28-29 23 30-31 24 32-34 25 35-36 26 37-40 27 41-43 28 44-47 29 48-51 30 52-56 31 132-156 39 57-62 32 157-191 40 63-69 33 192-244 41 70-76 34 245-334 42 77-86 35 335-519 43 87-97 36 520-1120 44 98-112 37 over 1120 45 113-131 38 Table II Minor C

20、haracteristics Sample Sample Sample Sample Lot Size Size Lot Size Size Lot Size Size Lot Size Size 1-9 all 14-16 12 28-33 16 77-121 20 10 9 17-18 13 34-41 17 122-273 21 11 10 19-22 14 42-54 18 over 273 22 12-13 11 23-27 15 55-76 19 4.3.2.1 Classification of characteristics (see 3.2). Critical, major

21、 and minor characteristics are defined in MIL- STD-105. Inspection shall be conducted as follows : 4.3.2.1.i Retainer (see dwg 8853794) covering a detail of dwg 8853792. Categories Characteris tics Method of Inspection Critical: None defined. Major: 101. Diameter of small hole, max (-1562) Gage 102.

22、 Diameter of large hole, max (.6562) Gage 104. Material (see 3. i) . .Visual 103. Thickness, min (.O211 Gage Minor: 201. Workmanship (see 3.3) .Visual-anual 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-V-4L70 LL m 9999706 0467L m , MIL-V-481

23、90 (MU) 4.3.2.1.2 Gasket (see dwg 8853797) covering a detail of dwg 8853792. Categories Characteristics Method of Inspection Critical: None defined. Major : 101. Diameter, min (.635) Gage 102. Thickness, min (.O721 . Gage 103. Material (see 3.1) .Visual 104. No tear, crack or hole.Visual Minor: 201.

24、 Workmanship (see 3.3) . Visual-Manual 4.3.2.1.3 Cap assembly (see dwg 8853792) covering a detail of dwg 8853791. Categories Characteristics Method of Inspection Critical: None defined. Major: 101. Objective evidence (see 6.2) for cap in accordance with MS 25043-1OC. .Visual 102. Objective evidence

25、(see 6.2) for rivet in accordance with MS 35743-1 Visual 103. Rivet tight Manual 104. No part missing Visual Minor: 201. Workmanship (see 3.3) . Visual-Manual 4.3.2.1.4 Plug (see dwg 8853795) covering a detail of dwg 8853791. Categories Characteristics Critical: None defined. Method of Inspection Ma

26、jor: 101. Pitch diameter of thread Gage . 102. Major diameter of thread Gage 103. Depth of groove in flange (.O401 ,max Gage 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-V-48l190 LlI = 9999906 0467882 T MIL-V-48190 (MU) 104. Diameter adjacen

27、t to flange (.635) Gage 105. Length of thread (.592) . Gage 106. Total length (.753) . Gage 108. Inside diameter, min (.348) .Gage 110. Objective evidence (see 6.2) for 107. Length to flange (.624) . Gage 109. Distance across flats of hex (1.00). Gage protective finish in accordance with dwg 8853795

28、Visual 111. Material (see 3.1) . Visual Minor : 201. Workmanship (see 3.3).Visual-Manual 4.3.2.1.5 Washer (see dwg 8853798) covering a detail of dwg 8853791. Cat ego r ie s Characteris tics Method of Inspection Critical: None defined. Major: 101. Inside diameter, max (.615) . Gage 102. Thickness, mi

29、n (.O721 .Gage 103. Outside diameter, min (.822). .Gage 104. No tear, crack or hole . Visual 105. Material (see 3.1). . .Visual Minor: None defined. 4.3.2.1.6 Vent assembly (see dwg 8853791) . Categories Characteris tics Method of Inspection Critical: None defined. Major : 101. No part missing Visua

30、l 102. Washer lies flat in groove and 103. Objective evidence (see 6.2) for nut extends above face of flange .Visual in accordance with Mc 39081-4Visual Minor : 201. Workmans.hip (see 3.3) .Visual- Manual 6 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS

31、-,-,-MIL-V-48170 11 m 993990b 0467883 L m MIL-V-48190 (MU) 4.3.2.1.7 Preparation for delivery (see 5. i) . Categories Characteristics Method of Inmection Critical: None defined. Major: 101. Preservation, packaging, packing and marking in accordance with MIL-STD-l169(MU) Visual-Manual Minor: None def

32、ined. 4 4.3.2.1.8 Bag, packing for repair parts (see dwg 8883535 coverinu Dart number 8883535-2 and 5.2). Categories Characteris tics Method of Inspection Critical: None defined. Major : 101. Material (see 3.1) . Visual 102. Length before packing, min*Measure 103. Width before packing, min.*Measure

33、104. Properly packed . Visual-Manual 105. Proper heat sealVisual-Manual 106. No hole or crack in bag Visual 107. Objective evidence (see 6.2) for heat seal test in accordance with MIL-P-l16Visual *Measure with suitable scale. Minor: 201. Marking Visual 202. Workrnanship (see 3.3). Visual-Manual 4.3.

34、2.1.9 Packing and marking for storage and shipments (see 8808362) and 5.2. Categories Characteristics Method of Inspection Critical: None defined. 7 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-V-48170 11 W 779770b 0467884 3 MIL-V-48190 (MU) M

35、ajor : 101. Gross load weight (max) .* Measure 102. Contents tight in package Manual 103. Correctly packed Visual-Manual 104. Material (see 3.1) .Visual *Determine weight with suitable scale. Minor: 201. Marking Visual 202. Workmanship (see 3.3) . Visual-Manual 4.3.3 Testing. Not applicable. 4.3.4 A

36、cceptance inspection equipment. 4.3.4.1 Critical and major characteristics and tests. Inspection and testing shall be performed with the acceptance inspection equipment, operating instructions, and calibration instructions specified on the Equipment Lists (EL). ELs for assemblies are listed on the E

37、quipment Tabulation, ET 8853791. When either of the conditions listed below exist, the con- tractor shall design required equipment or specify suitable commercial equipment and obtain approval prior to use on the contract. a. Any deviation from equipment or procedures specified on the EL is desired

38、(see 6.3). b. The code “CD“ is listed in the “Part or Identifying Number“ column on the EL (see 6.1.2). 4.3.4.2 Minor characteristics and tests. Acceptance inspection equipment for minor characteristics is not specified on ELs. operating instructions and calibration instructions used ,by the contrac

39、tor for minor classification inspection shall be approved by the Government representative authorized by the procuring agency. The acceptance inspection equipment, 4.4 Test methods. Not applicable. 5. PREPARATION FOR DELIVERY 5.1 Production items. 5.1.1 Preservation and packaging. Preservation and p

40、ackaging shall be level A or C as specified (see 6.1) 5.1.1.1 Level A. The vent assembly shall be preserved .and packaged in accordance with instructions contained,in MIL-STD-1169 (MU). 8 c PROBLEM HARD COPY Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IH

41、S-,-,-MIL-V-48190 11 H 9999906 0467885 5 H MIL-V-48190 (MU) 5.1.1.2 Level C. The vent assembly shall be preserved and packaged in accordance with instructions contained in MIL-STD-1169 (MU). 5.1.2 Packinq. 5.1.2.1 Levels A and C. The vent assembly shall be packed in accordance with the applicable in

42、structions con- - tained in MIL-STD-1169 (MU) . 5.1.3 Markinq. Marking shall be in accordance with MIL-STD-1169 (MU). 5.2 Repair parts. 5.2.1 Preservation and packaqing . Dackaaina shall be level A or C as spec L- 2 .a 5.2.1.1 Level A. The vent assemb in accordance with dwgs 8883535 and 880 Prece if

43、ied ( ly chal 8362 us rvat see 1 be ing ion and 6.1). I packaged the specified moisture barrier. in accordance with dwg 8808362 except that the moisture barrier may be omitted. 5.2.1.2 Level C. The vent assembly shall be packaged 5.2.2- Packing. 5.2.2.1 Level A and C. The vent assembly shall be 5.2.

44、3 Marking. Marking shall be as specified in ac- packed in accordance with dwgs 8883535 and 8808362. cordance with dwgs 8883535 and 8808362. 6. NOTES 6.1 Ordering data. Procurement documents should specify 6.1.1 Procurement requirements. the following: a. Title, number, and date of this specification

45、. b. Production or Repair Parts. c. Selection of applicable level of packaging and packing required (see 5.1 and 5.2). 6.1.2 Contract data requirements (see 4.3.4.1). Data spe- cified in 4.3.4.1 will be delivered as identified on a DI-E-118 when specified on a DD Form 1423 incorporated in the contra

46、ct. 6.2 Objective evidence. Records of contractor quality control and inspections which can be verified. 6.3 Acceptance inspection equipment (see 4.3.4.1). The contractor shall obtain approval from the Commanding Officer, Picatinny Arsenal, Dover, New Jersey 07801, ATTN: SMUPA-QA-N-I. Custodian: Army - MU Preparing activity: Project No. 1190-AO62 Army - MU 9 * U. S. GOVERNMENT PRINTING OFFICE: 1973-713- 146/1384 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-