ARMY MIL-V-44362-1989 VEST GRENADE CARRIER (FOR 40-MM GRENADES)《(40毫米手榴弹用)榴弹背心》.pdf

《ARMY MIL-V-44362-1989 VEST GRENADE CARRIER (FOR 40-MM GRENADES)《(40毫米手榴弹用)榴弹背心》.pdf》由会员分享，可在线阅读，更多相关《ARMY MIL-V-44362-1989 VEST GRENADE CARRIER (FOR 40-MM GRENADES)《(40毫米手榴弹用)榴弹背心》.pdf（18页珍藏版）》请在麦多课文档分享上搜索。

1、I INCH-POUND 1 MIL-V-443 62 ( GL) 9 March 1989 MILITARY SPECIFICATION VEST, GRENADE, CARRIER (FOR 40-m GRENADES) This specification is approved for use by the U.S. Army Natick Research, Development, and Engineering Center, Department of the Army, and is available for use by all Departments and Agenc

2、ies of the Department of Defense. 1. SCOPE I .1 Scope. This specification covers one type and size of nylon duck vest intended for carrying 40-mm grenades. 2. APPLICABLE DOCUMENTS 2.1 Government documents. 2.1.1 Specifications, standards, and handbooks. The following specifi- cations, standards, and

3、 handbooks form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those listed in the issue of the Department of Defense Index of Specifications and Standards (DODISS) and supplement thereto, cited in the solicitation (see 6.2). SPE

4、CIFICATIONS FEDERAL A-A-50083 - Bag, Plastic, Folded Garment DDD-L-20 - Label: for Clothing, Equipage and Tentage, (General Use) PPP -B-26 - Bag, Plastic (General Purpose) PPP-B-636 - Boxes, Shipping, Fiberboard Beneficial comments (recommendations, additions, deletions) and any pertinent data which

5、 may be of use in improving this document should be addressed to: U. S. Army Natick Research, Development, and Engineering Center, Natick, MA 01760-5014 by using the self-addressed Standardization Document Improvement Proposal (DD Form 1426) appearing at the end of this document or by letter. AMSC N

6、/A FSC 8415 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. THIS DOCUMENT CONTAINS /$ PAGES. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL -V -4 4 362 ( GL ) MILITARY MIL-L-35078 - Loads , Unit: Preparation of

7、Semiperishable Subsistence Items; Clothing , Personal Equipment and Equipage; General Specification for MIL-B-43826 - Belt , Individual Equipment STANDARDS MILITARY MIL-STD-105 - Sampling Procedures and Tables for Inspection by Attributes MIL-STD-129 - Marking for Shipment and Storage MIL-STD-147 -

8、Palletized Unit Loads MIL-STD-731 - Quality of Wood Members for Containers and Pallets (Unless otherwise indicated, copies of federal and military specifications, standards, and handbooks are available from the Naval Publications and Forms Center, (ATTN: NPODS) , 5801 Tabor Avenue, Philadelphia, PA

9、19120-5099.) . 2.1.2 Other Government documents , drawings , and publications. The following other Government documents, drawings, and publications form a part of this document to the extent specified herein. Unless otherwise specified , the issues are those cited in the solicitation. DRA Ki N GS U

10、.S. ARMY NATICK RESEARCH, DEVELOPMENT, AND ENGINEERING CENTER 2-1-2143 - Vest , Grenade, Assembly, 40-mm 2-1-21 70 - Vest, Back, Pattern 2 -6 - 103 - Cord Lock, Double Cord 5 - 10 -47 - Fastener, I-Inch (Copies of drawings are available from the U.S. Army Natick Research, Development , and Engineeri

11、ng Center., Natick, MA 01760-5014.) 2.2 Non-Government publications. The following document(s1 form a part of this document to the extent specified herein. Unless otherwise specified , the issues of the documents which-are DOD adopted are those listed in the issue of the DODISS cited in the solicita

12、tion. Unless otherwise specified, the issues of documents not listed in the DODISS are the issues of the documents cited in the solicitation (see 6.2). 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-V-44362 (GL) AMERICAN SOCIETY FOR TESTING AN

13、D MATERIALS ( ASTM) D 3951 - Standard Practice for Commercial Packaging (Application for copies should be addressed to the American Society for Testing and Materials, 1916 Race Street, Philadelphia, PA 19103-1187.) (Non-Government standards and other publications are normally available from the orga

14、nizations that prepare or distribute the documents. These documents also may be available in or through libraries or other informational services.) 2.3 Order of precedence. In the event of a conflict between the text of this document and the references cited herein, the text of this document takes p

15、recedence. Nothing in this document however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 First article. When specified (see 6.21, a sample shall be subjected to first article inspection ( 6.3) in accordance with 4.3, 3.2 Guide samples

16、. Guide samples, when furnished, are solely for guidance and information (see 6.4). Variations from the document may appear in the sample, in which case the document shall govern. 3.3 Materials. The materials shall be as specified on Drawing 2-1-2143 and all subsidiary drawings and parts lists perta

17、ining thereto. It is encouraged that recycled material be used when practical and as long it meets the require- ments of this specification. 3.4 Design and construction. The design and construction of the vest shall be as specified herein and as shown on Drawing 2-1-2143 and all subsidiary drawings

18、and parts lists (PLS) pertaining thereto. 3.4.1 Stitches, seams and stitches. All seams and stitchings shall be as specified on Drawing 2-1-2143 and subsidiary drawings pertaining thereto. 3.4.1 Automatic stitching. Automatic machines may be used to perform any of the stitch patterns provided the re

19、quirements for the stitch pattern, stitches per inch, and size and type of thread are met; and at least three tying, overlapping, or backstitches are used to secure the ends of the stitching. 3.4.1.2 Lubrication of thread. Thread lubrication is permitted providing it does not stain the materials use

20、d to fabricate the vest. Only nonwicking lubricants shall be used (see 4.4.1.1). 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- - _p MIL-V-44362 B4 m 9999906 0403702 3 4 MIL-V-44362(GL) 3.4.1.3 Type 301 stitching. Ends of all stitching shall be b

21、ackstitched or overstitched as specified on the drawings except where ends are turned under or caught in other seams or stitching. there will be no loose stitching resulting in loose bobbin or top thread or excessively tight stitching resulting in puckering of the materials sewn. lock shall be imbed

22、ded in the materials sewn. Thread tensions shall be maintained so that The 3.4.1.3.1 Repairs of type 301 stitching. Repairs of type 301 stitching shall be as follows: a. When thread breaks or bobbin run-outs occur during stitching, the stitching shall be repaired by restarting the stitching a minimu

23、m of 1 inch (3/8 inch for box and box-x stitching) back of the end of the stitching. b. Thread breaks, or two or more consecutive skipped or runoff stitches noted during inspection of the item (in-process or end item) shall be repaired by overstitching. defective area (3/8 inch on box and box-x stit

24、ching), continue over the defective area, and continue a minimum of 1 inch (3/8 inch on box and box-x stitching) beyond the defective area onto the existing stitching. Loose or excessively tight stitching shall be repaired by removing the defective stitching without damaging the materials, and resti

25、tching in the required manner The stitching shall start a minimum of 1 inch in back of the (When making the above repairs in a. and b. above, the ends of the stitching are not required to be backstitched.) 3.4.1.4 Bartacking. Bartacking shall be 3/4 + 1/16 inch in length and 1/8 + 1/32 inch in width

26、 and shall contain 42 stTtches. free-from thread breaks and loose or tight stitching. Bartacking shall be 3.4.1.5 Thread ends. All thread ends shall be trimmed to l/4 inch maximum length. 3.4.2 Fusing of ends of nylon webbing, cord, and material. Ends of webbing, including bias cuts, cord and raw ed

27、ges of nylon material shall be fused smooth. Fusing of the webbing ends and nylon material shall be accomplished prior to assembling for stitching. and material shall be capable of providing sufficient heat to provide a smooth edge with the cut ends of the yarns fused together to prevent separation.

28、 The apparatus used to fuse the webbing and cord ends, 3.4.3 Location marks. Location marks shall not be drilled. Printed markings shall not be more than 1/32-inch in width. 3.4.4 Repairs. Repairs such as mends, darns, patches,or splices are not permitted on the vests. 3.4.5 Replacement of defective

29、 components. During the spreading, cutting and manufacturing process, components having material defects or damages that are classified as defects in 4.4.3, shall be removed from production and replaced with non-defective and properly matched components, 4 Provided by IHSNot for ResaleNo reproductio

30、n or networking permitted without license from IHS-,-,-I MIL-V-i93b2 4 777790b 0903703 5 MIL -V -4 4 3 6 2 ( GL ) 0 3.4.6 Setting of eyelets. Holes shall be prepunched or drilled to receive the eyelets. Holes prepunched to receive the eyelets shall be smaller than the outside diameter of the eyelet

31、barrel so that the barrel must be forced through the hole. 3.4.6.1 Eyelets, with washer, brass. The brass eyelets with washer shall be securely clinched in a manner that will prevent detachment from or cutting of the surrounding material. The eyelets shall be clinched without splitting. 3.4.7 Settin

32、g of grommets. Holes shall be prepunched or drilled to receive the grommets. Holes prepunched to receive the grommets shall be smaller than the outside diameter of the grommet barrel so that the barrel must be forced through the hole. The grommet shall be securely clinched without cutting the adjace

33、nt material. 3.4.8 Setting of snap fasteners. A hole shall be prepunched or drilled to receive the button and eyelet components of the snap fasteners. The hole shall be smaller than the outside diameter of the button and eyelet barrels so that the barrel must be forced through the hole. The hole sha

34、ll not be punched in the setting operation with the button or eyelet barrel. The fasteners shall be securely clinched without cutting the adjacent materials and no more than three splits shall occur in the button or eyelet barrels. 3.5 Marking. The letters 11US1 shall be applied in the size characte

35、rs and in the location indicated on Drawing 2-1-2143 and shall conform to type IV, class 9 of DDD-L-20. Fastness of class 9 marking shall be as specified for class 5 mar king. 3.6 Combination identification and instruction label. A combination identi- fication and instruction label shall be applied

36、on the inside of the back part as indicated on Drawing 2-1-2170. The label shall conform to type VI, class 15 of DDD-L-20. The label color shall be medium green, cable number 70034, 70130 or 70131. The legend shall be located on the label so that no part of the legend will be obscured by stitching o

37、r binding when sewn on the vest back part. The instructions shall be as follows: HAND WASHING Scrape dirt/dust from the vest using a brush or flat stick which will not cut Wash vest in a pail of warm water using mild detergent or soap. Rinse thoroughly in clean water. Do not use Chlorine Bleach, Yel

38、low Soap, Cleaning Fluids or Solvents as these will discolor/deteriorate the item. Dry item in shade or indoors. Do not launder or dry item in Fixed/Commercial/Home Type Laundry Equipment. Do not attempt to dye item or repair it. Turn in for repair/replacement. fabric/ webbing . 5 Provided by IHSNot

39、 for ResaleNo reproduction or networking permitted without license from IHS-,-,-_ l_ I_ _- - . - MIL-V-443b2 84 m 9999906 040370Y 7 m MIL-V-44362(GL) Use considerations: 1. During high combat stress situations, the easiest to reach rounds are to be extracted first. 2. During low combat stress situat

40、ions, the rear most rounds are to be extracted first. 3. The vest should be worn with the chest straps and equipment belt unfast- ened during water borne or water crossing operations. 3.6.1 Component cutting and marking. Cut all parts of the vest out of one piece of material except for pocket reinfo

41、rcement material which may be cut from ends or printed seconds. Printed seconds shall be cloth which has been rejected only for defects pertaining to color, infrared reflectance, or camouflage printed pattern as specified in MIL-C-43734. In addition, the cloth for pocket reinforcing material may be

42、dyed Olive Green 106, water repellent treated, conforming to all other requirements of MIL-C-43734. The component parts of the vest shall be cut, marked and bundled to insure uniform size and shade through- out the vest. The following marking methods shall not be used: a. Corrosive metal fastening d

43、evice b, Sew-on type ticket c. Adhesive type ticket which leave an impression or traces of paper or adhesive on the material upon removal of the ticket. 3.7 Patterns. Standard pattern drawings for textile components other than tape or webbing are shown full scale on drawings and provide allowances f

44、or all seams and shall be used for making working patterns. The standard pattern shall not be altered in any way. 3.8 Workmanship. The vest shall conform to the quality of product estab- lished by this specification and occurrence of defects shall not exceed the applicable acceptable quality levels.

45、 4. QUALITY ASSURANCE PROVISIONS 4.1 Responsibility for inspection. Unless otherwise specified in the .contract or purchase order, the contr ctor is responsible for the perform all inspection requirements (examinations and tests) as specified herein. nce of Except as otherwise specified in the contr

46、act or purchase order, the contractor may use his own or any other facilities suitable for the performance of the inspection requirements specified herein, unless disapproved by the Government. The Government reserves the right to perform any of the inspections set forth in this specification where

47、such inspections are deemed necessary to ensure supplies and services conform to prescribed requirements. 4.1.1 Responsibility for compliance. All items shall meet all requirements of sections 3 and 5. The inspection set forth in this specification shall become a part of the contractors overall insp

48、ection system or quality program. The absence of any inspection requirements in the specification shall not relieve the contractor of the responsibility of ensuring that all products or supplies submitted to the Government for acceptance comply with all requirements of the contract. Sampling inspect

49、ion, as part of manufacturing Operations, is an acceptable practice to ascertain conformance to requirements, however, this does not authorize submission of known defective material, either indicated or actual, nor does it commit the Government to accept defective material. 6 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL -V -4 4 3 6 2 ( GL ) 4.1.2 Responsibility for dimensional requirement