ARMY MIL-T-63278-1979 TEST SET ELECTRONIC SYSTEMS M91 REPAIR PARTS FOR《M91电子系统测试装置的备用零件》.pdf

《ARMY MIL-T-63278-1979 TEST SET ELECTRONIC SYSTEMS M91 REPAIR PARTS FOR《M91电子系统测试装置的备用零件》.pdf》由会员分享，可在线阅读，更多相关《ARMY MIL-T-63278-1979 TEST SET ELECTRONIC SYSTEMS M91 REPAIR PARTS FOR《M91电子系统测试装置的备用零件》.pdf（17页珍藏版）》请在麦多课文档分享上搜索。

1、MIL-T-63278 (AR) 12 March 1979 M IL I TARY SPEC I FI CATION TEST SET, ELECTRONIC SYSTEMS:. M91; REPAIR PARTS FOR This specification is approved for use by the US Army Armament Research and Development Command,. and is available for use by all Departments and Agencies of the Department of Defense. 1.

2、 SCOPE 1.1 This specification covers the inspection and packaging of repair parts for the M91 Electronic Systems Test Set. 2. APPLICABLE DOCUMENTS 2.1 Issues of documents.- The following documents of the issue in effect on date of invitation for bids or request for proposal, form a part of this spec

3、ification to the extent specified herein. SPECIFICATIONS MIL I TARY MIL-A-48078 - Ammunition, Standard Quality Assurance Provisions, General Specification For MIL-T-63263(AR) - Test Set, Electronic Systems:. M91 STANDARDS MILITARY MIL-STD-1188 - Comercial Packaging of Supplies and Equipment MIL-STD-

4、1460 - Soldering of Electrical Connections and . Printed Wiring Assemblies, Proce- du res. for MIL-STD-454 - Standard General Requirements for . Electronic Equipment FSC: 4925 Beneficial commenta (recommendations, additions, deletions) and any pertinent data which may be of use in improving this doc

5、ument should be addressed ta: Commander, US Army Armament Research and Development Command, Ath, DRDARQA, Dover, New Jersey 07801 by using the self-addressed Standardization Document Improvement Proposal (DD Form 1426) appearing at the end of this document or by letter. Provided by IHSNot for Resale

6、No reproduction or networking permitted without license from IHS-,-,-MIL-T-b327 Y9 999990b 0252727 MIL-T-63278 (AR) DRAWINGS (See 6.3) US ARMY ARMAMENT RESEARCH AND DEVELOPMENT COMMAND 9326182 9326766 9326701 9325989 9 326 142 9326143 9326144 9326145 932 67 33 9 326 2 14 9326864 11 8 2 8 98 2 118289

7、88 11828993 11828996 11829000 11829003 11829005 11829010 11829011 9 325999-1 Test Set, Electronic Assembly Case, Carrying Screwdriver, Ball, Hex Key Cable Assembly, Power Cable No. 1 Printed Circuit Board No. 1 Printed Circuit Board No. 2 Printed Circuit Board No. 3 Printed Circuit Board No. 4 Stud

8、Nut Vol tage Regulator Knob Assembly Switch , Rotary Packing and Marking for Box, Exterior for Test Set, Electronic Assembly: M91 Packing and Marking for Box, Exterior for Case, Carrying Packing and Marking for Box, Exterior for Screwdriver, Ball Hex Key Packing and Marking for Box, Exterior for Cab

9、le Assembly, Power Cable No. 1 Packing and Marking for Box, Exterior for Printed Circuit Board No. 1, 2, 3, or 4 Packing and Marking for Bag, Polyethylene for Stud Nut Packing and Marking for Box, Exterior for Vol tage Regulator Packing and Marking for Bag, Polyethylene for Knob Assembly Packing and

10、 Marking for Box, Exterior for Rotary Switch 3. REQUIREMENTS 3.1 Materials.- Materials shall be in accordance with appl i cable drawings and spec if i cati ons . 3.2 Parts and assemblies. - The parts and assemblies shall comply with all requirements specified on the applicable drawings and with all

11、requirements specified on applicable specifications. cables, connectors, components and assemblies shall be performed in a thorough, workman1 ike manner in accordance with MIL-STD-1460 or 3.3 Wiring and soldering. - Soldering of electrical wires, MIL-STD-454 2 Provided by IHSNot for ResaleNo reprodu

12、ction or networking permitted without license from IHS-,-,-MIL-T-63278 (AR) 3.4 Workmanship.- All parts shall be fabricated and finished in a thorough, workmanlike manner. chips, sharp edges, cracks, unblended radii , surface defects, dirt, grease, rust , corrosion products, and other foreign matter

13、. cleaning method used shall not be injurious to any part nor shall the parts be contaminated by the cleaning agents. markings shall be neat and sharply defined. They shall be free of burrs, The All required 4. QUALITY ASSURANCE PROVISIONS 4.1 Responsibility for inspection and standard quality assur

14、ance provisions.- Unless otherwise specified herein or in the contract, the provisions of MIL-A-48078 shall apply and are hereby made a part of this detail specification. 4.2 Classification of inspections.- The following type of inspection shall be conducted on this item. a. Quality conformance insp

15、ection. 4.3 First article inspection. - Not appl 4.4 Quality conformance inspection 4.4.1 Inspection lot formation. - Inspect with the 1 ot f ormati on provi si ons of MIL-A-480 cable on lots shall comply 8. 4.4.2 Examination. - See MIL-A-48078. a. Unless otherwise specified in the classification of

16、 defects and test tables, sampling plans for major and minor defects shall be in accordance with MIL-STD-105, Inspection Level II. e Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-T-63278 49 m 9999906 0252729 L W I rs Li O al .I 4 Provided by IH

17、SNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-I rl k ri 7 m N T? m mm Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-. Q 60 rl Q) o a *rl 3 w Q 6 3 I Provided by IHSNot for ResaleNo reproduction or networking pe

18、rmitted without license from IHS-,-,-MIL-T-63278 49 W 9999906 0252732 L I E u o w 5 U c-4 mc-4 3 m mm m . . . o 00 a ri a d % a, z f3 O a ct a, o a Q Q) : -0 m 3 n 3 ri 7 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-. F=i I d! gag E Y O & m W *. O

19、6 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-T-63278 L17 M 7997906 025273q 5 E cn c in EI c I ri b d rd B wo) sg Id W :? 01 m om a rl a $ 9 al 8 !z v) P Id rl Ici o) v) rl rdI 9 Provided by IHSNot for ResaleNo reproduction or networking perm

20、itted without license from IHS-,-,-a, il .a l?J o n Y O n Oe4 O0 mm rlrl mm EE ri *rl 33 nl Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-? cvcvc.Icv moom o a, z % O a ri ,I 11 a Provided by IHSNot for ResaleNo reproduction or networking permitted

21、without license from IHS-,-,-d! E gag U8 rl Q O A h O Qi o d 9.4 3 w B Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-T-63278 Li7 m 7777906 0252738 2 = ? CI (i3 (i3 13 Provided by IHSNot for ResaleNo reproduction or networking permitted without

22、license from IHS-,-,-I F1 6 FI E a Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-T-6327B 47 W 7977706 0252740 O I ! . Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-T-63i78 49 479440b 02527

23、43 2 I MIL-T-63278 (AR) 4.4.3 Testing. - Testing is described in the Quality Confor- 4.4.4 Inspection equipment.- The inspection equipment required mance Inspecti on Tables. to per-form the examinations and tests prescribed herein is described in the Paragraph Reference/Inspection Method column in t

24、he tables starting with Paragraph 4.4.2.1. The contractor shall submit for approval inspection equipment designs in accordance with the terms of the contract. See Section 6 of MIL-A-48078 and 6.2 herein, 5. PREPARATION FOR DELIVERY 5.1 Packaging - Packaging shall be as specified on the drawings bel

25、ow: Noniencl ature Pkg Dwgs Test Set, Electronic Assembly Case, Carrying Screwdriver, Ball, Hex Key Cable Assembly, Power Cable No. 1 Printed Circuit Board No. 1, 2, 3, or 4 Stud Nut Vol tage Regulator Knob Assembly Switch, Rotary 11828982 11 828988 11828993 11828996 11829000 11829003 11829005 11829

26、010 11829011 5.2 Packing and Marking. - Packing and marking shall be in accordance with the comercial requirements of MIL-STD-1188. 6. NOTES 6.1 Ordering data.- See MIL-A-48078. 16 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-Preparing Activity: Army - AR Project Number: 4925-AO33 *“.S. GOVERNMENT PRINTING OFFICE: 1979-603-022/1796 17 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-