ARMY MIL-T-62319 C-1989 TRUCKS CARGO DIESEL OR GASOLINE ENGINE DRIVEN 19 000 TO 24 000 POUNDS GVW 4X2 AND 4X4 COMMERCIAL《19 000 至 24 000 磅 GVW 4X2及4X4型 柴油冀汽油发动机驱动的货车》.pdf

《ARMY MIL-T-62319 C-1989 TRUCKS CARGO DIESEL OR GASOLINE ENGINE DRIVEN 19 000 TO 24 000 POUNDS GVW 4X2 AND 4X4 COMMERCIAL《19 000 至 24 000 磅 GVW 4X2及4X4型 柴油冀汽油发动机驱动的货车》.pdf》由会员分享，可在线阅读，更多相关《ARMY MIL-T-62319 C-1989 TRUCKS CARGO DIESEL OR GASOLINE ENGINE DRIVEN 19 000 TO 24 000 POUNDS GVW 4X2 AND 4X4 COMMERCIAL《19 000 至 24 000 磅 GVW 4X2及4X4型 柴油冀汽油发动机驱动的货车》.pdf（31页珍藏版）》请在麦多课文档分享上搜索。

1、OT MEASUREMENT SENSITIVE/ 3: MIL-T-62319C 28 Julv 1989 SUPERSEDING 2 November 1984 MIL-T-62319B Class Model Nomenc 1 at ur e CDE 4x2 4 wheel, 2 wheel drive -c E 4x4 4 wheel. 4 whe el drive MILITARY SPECIFICATION TRUCKS, CARGO: DIESEL OR GASOLINE ENGINE DRIVEN, 19,000 TO 24,000 POUNDS GVW, 4x2 AND 4x

2、4, COMMERCIAL This specification is approved for use by al1 Departments and Agencies of the Department of Defense. 1. SCOPE * 1.1 ScoDe. This specification covers diesel or gasoline engine driven, four-wheel, two-rear-wheel drive, and four-wheel, four-wheel drive cargo trucks, having minimum gross v

3、ehicle weights (GW) of 19,000 to 24,000 pounds, for normal operating conditions. The vehicles procured under this specification are commercial items which shall be warranted by the manufacturer as specified in acquisition documents. 1.2 Vehicle classification. The vehicle shall be one of the classes

4、 and models shown in table I, as specified (see 6.2): TABLE I. Vehicle classification. Beneficial comments (recommendations, additions, deletions) and any pertinent data which may be of use in improving this document should be addressed to: US Army Tank-Automotive Command, ATTN: AFiSTA-UED, Warren,

5、MI 48397-5000, by using the self-addressed Standardization Document Improvement Proposal (DD Form 1426) appearing at the end of this document or bv letter. AMSC NIA -1 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. Y . THIS DOCUMENT CONTAINS 4 /- - -. PAGES. Provid

6、ed by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-1.2.1 Class. The class of the vehicle shall be determined by the minimum GVW rating as follows: Class C . . . 19,000 pounds Class D . . . . . 21,000 pounds Class E . . 24,000 pounds 2. APPLICABLE DOCUMENTS 2

7、1 Government document g. * 2.1.1 Specifications, standards and bandbooka. The following specifications, standards and handbooks form a part of this specification to the extent: specified herein. Unless otherwise specified, the issues of these documents are those listed in the issue of the Department

8、 of Defense Index of Specifications and Standards (DODISS), and supplement thereto, cited in the solicitation (see 6.2) * SPECIFICATIONS FEDERAL W-B-131 VV-F-800 ZZ -T-3 8 1 ccc-e419 MILITARY MIL-T-5 624 MIL-M-43719 MIL-B-46176 MIL-T-83133 STANDARDS FEDERAL FED-STD-297 - Battery, Storage: Vehicular,

9、 Ignition, - Fuel Oil, Diesel, - Tires, Pneumatics Vehicular (Highway) - Cloth, Duck, Cotton, Unbleached Plied Yarns, Lighting and Starting, Army and Numbered. - Turbine Fuel, Aviation, Grades JP-4 and - Marking Materials and Markers, Adhesive, JP-5 . Elastomeric, Pigmented, General Specification Fo

10、r. Weather, Operational and Preservative. - Brake Fluid, Silicone, Automotive A11 - Turbine Fuel, Aviation, Kerosene Type, Grade JP-8 o - Rustproof ing of Commercial (Nontactical) Vehicles . 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-NIL-T-623

11、L7C 23 m 7777706 0202577 O m MIL-T-62319C MIL I TARY MIL-STD-1223 - Nontactical Wheeled Vehicles Treatment, Painting, Identification Marking and Data Plate Standards. Capacity, Manual Release. Capacity, Manual Release. Intervehicular, 28-Volt, Waterproof. Contact, Intervehicular, 28-Volt, Waterproof

12、. MS51118 - Pintle Assembly, Towing - 40,000 Lbs. MS51335 - Pintle Assembly, Towing - 18,000 Lbs. MS75020 - Connector, Plug, Electrical - 12 Contact, MS75021 - Connector, Receptacle, Electrical - 12 J; (Unless otherwise indicated, copies of federal and military specifications, standards and handbook

13、s are available from the Naval Publications and Forms Center, (ATTN: NPODS), 5801 Tabor Avenue, Philadelphia, PA 19120-5099.) * 2.1.2 Other Government documents. drawines an d Dubiications. The following other Government documents, drawings and publications form a part of this document to the extent

14、 specified herein. Unless otherwise specified, the issues are those cited in the solicitation. DEPARTMENT OF DEFENSE (DoD) - Department of Defense Index of Specifications and Standards. /- * DODISS (Copies of the DODISS are available on a yearly subscription basis either from the Government Printing

15、 Office for hard copy, or microfiche copies are available from the Director, Navy Publication and Printing Service Office, 700 Robbins Avenue, Philadelphia, PA 19111-5093.) DEPARTMENT OF TRANSPORTATION (DOT) Federal Motor Carrier Safety Regulations. Federal Motor Vehicle Safety Standards. (Applicati

16、on for copies of DOT publications should reference the Code of Federal Regulations, 49 CFR, and the Federal Register, and should be addressed to the Superintendent of Documents, U.S. Government Printing Office, Washington, D.C. 20402.) ENVIRONMENTAL PROTECTION AGENCY (EPA) Control of Air Pollution f

17、rom New Motor Vehicles and New Motor Vehicle Engines. Noise Emission Standards for Transportation Equipment - Medium and Heavy Trucks. (Application for copies of EPA publications should reference the Code of Federal Regulations, 40 CFR, and the Federal Register and should be addressed to the Superin

18、tendent of Documents, U. S. Government Printing Office, Washington, D.C. 20402.) 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-T-523 19C * 2.2 N.on-Government D ublicatione. The following documents form a part of this document to the extent s

19、pecified herein. the issues of the documents which are DOD adopted are those listed in the issue of the DODISS cited in the solicitation. Unless otherwise specified, the issues of documents not listed in the DODISS are the issue of the documents cited in the solicitation (see 6.2). Unless otherwise

20、specified, AMERICAN SOCIETY FOR TESTING AND MATERIALS (AST%) ASTM Standards, Al 20 - Pipe, Steel, Black and Hot-Dipped Zinc -Coated (Galvanized) Welded and Seamless, for Ordinary Uses (DOD adopted). (Application for copies of ASTM publications should be addressed to the American Society for Testing

21、and Materials, 1916 Race Street, Philadelphia, PA 19103,) * THE EUROPEAN TYRE AND RIM TECHNICAL ORGANISATION (ETRTO) Standards Manual (Application for copies of ETRTO publications should be addressed to the European Tyre and Rim Technical Organisation, 32, Avenue Brugmann, 1060 Brussele, Belgium.) S

22、AE, Ince SAE Standards and Recommended Practices. 531 8 5350 f53 7 5551 5560 5588 5589 5682 56 83 5688 5704 Air Brake Gladhand Service (Control) and Emergency (Supply) Line Couplers - Trucks, Truck-Tractors, and Trailers (DOD adopted). Spark Arrester Test Procedure for Medium Size Engines (DOI) adop

23、ted). Storage Batteries. Performance Levels and Methods of Measurement of Electromagnetic Radiation from Vehicles and Devices (30-1000 MHz). Seven-Conductor Electrical Connector or Truck-Trailer Jumper Cable. Turn Signal Lamps. Turn Signal Switch. Rear Wheel Splash and Stone Throw Protection (DOD ad

24、opted) . Tire Chain Clearance - Trucks, Buses, and Comb inat ions of Vihicles. Truck Ability Prediction Procedure (DOD adopted) Openings for Six- and Eight-Bolt Truck Transmission Mounted Power Take-offs. s 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from I

25、HS-,-,-5706 5844 51067 51349 NIL-T-623L7C 23 7777706 02025L 7 MIL-T-623 19C - Rating of Winches. - Nonmetallic Air Brake System Tubing (DOD - Seven-Conductor Jacketed Cable for - Engine Power Test Code - Spark Ignition and adopted). Truck-Trailer Connections. Diesel. (Application for copies of SAE p

26、ublications should be addressed to SAES Inc., 400 Commonwealth Drive, Warrendale, PA 15096.) THE TIRE AND RIM ASSOCIATION, INC, Yearbook. (Application for copies of Tire and Rim Association publications should be addressed to the Tire and Rim Association, Inc., 3200 W. Market Street, Akron, OH 44313

27、.) * from the organizations that prepare or distribute the documents. These documents also may be available in or through libraries or other informational services.) (Non-Government standards and other publications are normally available * 2.3 Order of precedence. In the event of a conflict between

28、the text of this document and the references cited herein, the text of this document takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS * 3.1 Standard vehicle and accessories. Except as specif

29、ied in 3.1.1 through 3.1.1.14, the vehicle, components, assemblies, and accessories to be delivered under the contract shall be standard or optional items, which meet or exceed the requirements of this specification. Except as specified in 3.1.1 through 3.1.1 J4, no removal, substitution or alterati

30、on of the chassis manufacturers standard or optional chassis model component shall be made. All chassis items shall be as represented in the chassis manufacturers technical data book, Special bodies or mounted equipment shall be as represented in the body and equipment manufacturers technical data.

31、Technical data shall be limited to specifications and technical material identical to that furnished to the authorized company representatives for selection of vehicle models and components, and shall be available to the engineering offices of the procuring activity, prior to delivery of the items.

32、The chassis model furnished .shall be not older than the chassis manufacturers current model on the date of invitation for bids. 3.1.1 Special reauirements. In addition to the standard vehicle and components specified in 3.1 , the vehicle shall be furnished with special equipment as specified herein

33、. 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-T-62319C 3a1.1.1 Painting and markino. Treatment, painting, marking and data plates shall be in accordance with MIL-STD-1223. identification markings shall be in accordance with the requirements

34、 of MIL-STD-1223 for the military service identified by the procuring activity (see 6.2) . The exterior color and the 3.1.1.2 Rustoroof ing. When specified (see 6.2), the vehicle shall be rustproofed in accordance with FED-STD-297. tropical rustproof ing in accordance with FED-STD-297 shall be furni

35、shed. When specified (see 6.2), 3.1.1.3 Drain oluvs. Drain plugs installed in manual transmissions, transfer cases and rear axles shall be of the permanent magnet type. * 3.1.1.4 Wood treatme nt. As specified herein (see 3.5.4.1) , wood surfaces shall be treated in accordance with MIL-STD-1223. 3.1.

36、1.5 Towinn.deviceg. Not less than two hooks, loops, or pins for towing the vehicle shall be furnished on the front of the vehicle. * 3.1.1.6 Wheel sDiash a nd stone throw rjrotection. The vehicle shall have rigid splash shields ahead of the rear wheels and rubber mud flaps to the rear of the rear wh

37、eels. All tilt cabs shall have rubber mud flaps to the rear of the ront wheels. A metal strip not less than 118 inch thick and not less than one inch wide, extending the entire width of the mud flap, shall be installed to prevent the bolt heads or bolt nuts from damaging the mud flap. As an alternat

38、e method of attaching the mud flaps, tabs or clips with minimum surface contact dimensions of 1 inch high by 1-114 inch wide by 3/32 inch thick shall be furnished at each bolt. installations, front and rear, shall conform to the rear wheel splash and stone throw protection provisions of SAE 5682. Al

39、l splash shield and mud flap * 3.1.1.7 ck . A trailer towing package consisting of a pintle, safety chain attachment devices, a lighting receptacle, a trailer brake control system and associated reinforcements and wiring shall be installed on the rear of the vehicle. type conforming to MS51335-1 for

40、 class C and D vehicles and to MS51118-1 for class E vehicles. reinforcements to transfer a vertical tongue load of not less than 1,800 pounds and a horizontal drawbar load of not less than 18,000 pounds for class C and D vehicle6; and a vertical tongue load of not less than 4,000 pounds and a horiz

41、ontal drawbar load of not less than 40,000 pounds for class E vehicles directly to the chassis rails. The rearmost portion of the pintle shall be forward, but not more than four inches forward, of the rearmost part of the vehicle. Two trailer safety chain attachment devices, one adjacent to each sid

42、e of the pintle, shall be provided. provide an ultimate strength at least equal to the GVW of the truck furnished, The attachment devices for class C and D vehicles shall be capable of accommodating a standard grab hook (2-3/16 inches wide, 47/64-inch The pintle shall be of the rotating The pintle s

43、hall be installed on the chassis frame with Each attachment device shall 6 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-T-bZ3LSC 23 m 9777706 0202583 2 m MIL-T-62319C thick and 31/64-inch throat width) for a 3/8 inch chain; the attachment devi

44、ces for a class E vehicle shall be capable of accommodating a standard grab hook (4-9/16 inches wide, 1-3/16 inches thick, 25/32-inch throat width) for a 5/8-inch chain. its conductors connected and color coded as specified therein, shall be mounted in a readily accessible location near the pintle.

45、The trailer brake control system shall conform to 3.4.11.3. The lighting receptacle, conforming to SAE J560 with * 3.1.1.7.1 Pintle height. When specified (see 6.21, the pintle shall be mounted on an added member, braced to the main frame rails at a height above the ground level of 22 inches, plus o

46、r minus 2 inches, with the truck at curb weight. The mounting structure and welds shall be capable of transmitting a drawbar pull at least equal to the rated tongue and drawbar load of the pint le. s. 3.1.1.8 Trailer lighting cable. When specified (sec 6.21, a trailer lighting cable conforming to SA

47、E 51067 shall be furnished. The cable shall be coiled and shall be not less than 110 inches long when fully extended. Both ends of the cable shall be equipped with a round plug conforming to SAE 5560. The plugs shall be equipped with a grip for withdrawing from the connector sockets. The cable shall

48、 be packaged and stowed in the vehicle tool compartment. * 3.1.1.9 Hydraulic tailCate. When specified (see 6.21, the vehicle shall be equipped with an electric motor driven hydraulic tailgate having not less than 2,000 pounds rated capacity. All hydraulic cylinders shall be provided with flow restri

49、ctors in the downport of the cylinders to prevent the tailgate from falling rapidly in the event of hydraulic system failure. The tailgate platform shall be of the ramping type and shall have a depth of not less than 32 inches exclusive of the ramp. The ramp shall taper down to the ground level to facilitate loading with wheeled hand carts. Platform loading area shall be of nonskid sheet steel. Latches to hold the tailgate- during loading and unloading of the tru