ARMY MIL-T-10168 J-1986 TENT FRAME-TYPE INSULATED SECTIONAL WITH FLOOR 16 FEET WIDE M1948 COMPLETE《M1948 16英寸宽带地板剖面绝缘架式帐篷》.pdf

《ARMY MIL-T-10168 J-1986 TENT FRAME-TYPE INSULATED SECTIONAL WITH FLOOR 16 FEET WIDE M1948 COMPLETE《M1948 16英寸宽带地板剖面绝缘架式帐篷》.pdf》由会员分享，可在线阅读，更多相关《ARMY MIL-T-10168 J-1986 TENT FRAME-TYPE INSULATED SECTIONAL WITH FLOOR 16 FEET WIDE M1948 COMPLETE《M1948 16英寸宽带地板剖面绝缘架式帐篷》.pdf（54页珍藏版）》请在麦多课文档分享上搜索。

1、b - . MIL-T-10168 30 June 1986 SUPERSEDING MIL-T -1 O 168H 19 June 1972 MILITARY SPEC IF IC AT I ON TENT, FRAME -TYPE, INSULATED , SECT IONAL , WITH FLOOR, 16 FEET WLDE,.M1948, COMPLETE This specification is approved for use by all Departments and Agencies of the Department of Defense. 1- SCOPE 1.1

2、Scope. This document covers one type of general purpose insulated frame-type tent with floor. Identical parabolic ends with entrance doors provide for a detachable vestibule that may be used at either end. erected, inside width at floor level is 16 feet, and inside length is expandable in multiples

3、of 4 feet. One each electrical outlet and switch assembly for lighting is designed for use with a combination of sectional units completing an inclosure of 16 by 16 feet in size. When 2. APPLICABLE DOCUMENTS n 2.1 Government documents. Unless otherwise specified, the following documents of the issue

4、 in effect on the date of invitation for bids or request for proposal form a part of this document to the extent specified herein. SPECIFICATIONS FEDERAL A-A-2 094 - Tape, Insulation, Electrical (Friction) J-C-580 - Cord, Flexible, and Wire, Fixture L-P-349 - Plastic Molding and Extrusion Material,

5、Cellulose Acetate Butyrate Beneficial comments (recommendations, additions, deletions) and any pertinent data which may be of use in improving this document should be addressed to U.S. Army Natick Research, Development, and Engineering Center, Natick, MA 01760-5014, by using the self -addressed Stan

6、dardization Document Improvement Proposal (DD Form 1426) appearing at the end of this document or by letter. AMSC N/A FSC 8340 DISTRIBUTLON STATEMENT A. Approved for public release; distribution is unlimited. THIS DOCUMENT CONTAINS 54 PAGES. - Provided by IHSNot for ResaleNo reproduction or networki

7、ng permitted without license from IHS-,-,-V-T-2 8 5 W-F -406 W-J-800 FF-B-584 FF-H -1 16 FF-N-105 FF-S -1 1 1 FF-P-386 FF-T-1813 QQ-S-571 QQ-S-698 QQ-S-7 O0 QQ-S-781 RR-C-271 R-W-365 IT-C-5 98 TT -E-5 29 TT -P - 63 6 UU-P-2 68 DDD-L -2 O MMM-A-181 PPP-13-62 1 PPP-C -843 PPP-T-45 PPP-T-60 MILITARY MI

8、L-C-4 9 6 MIL-P - 50 1 MIL-W-5 3 O MIL-B-5 43 MIL-L-1709 MIL-S-173 4 MIL-C-2399 MIL-T-LOLbJ 83 W 77777Ob 037bbLb 5 MIL-T-10168J - Thread, Polyester - Fittings for Cable, Power, Electrical and Conduit, Metal, Flexible - Junction Box: Extension, Junction Box; Cover, Junction Box (Steel, Cadmium, or Zi

9、nc-Coated) - Bolts, Finned Neck; Key Head; Machine; Ribbed Neck; Square Neck; Tee Head - Hinges, Hardware, Builders - Nails, Brads, Staples and Spikes: Wire, Cut and Wrought - Screw, Wood - Pins, Cotter, (Split) - Tack - Solder, Tin Alloy: Tin-Lead Alloy; and Lead Alloy - Steel Sheet and Strip, Low

10、Carbon - Steel Sheet and Strip, Medium and High Carbon - Strapping, Steel, and Seals - Chains and Attachments, Welded and Weldless - Wire, Fabric (Insect Screening) - Caulking Compound, Oil and Resin Base Type (for - Enamel, Alkyd, Semigloss - Primer Coating, Alkyd, Wood and Ferrous Metal - Paper, K

11、raft, Wrapping - Label: for Clothing, Equipage, and Tentage, - Adhesives, Phenol, Resorcinol, or Melamine Base - Boxes, Wood, Nailed and Lock-Corner - Cushioning Material, Cellulosic - Tape, Gummed, Paper, Reinforced and Plain for - Tape: Packaging, Waterproof Building Construction) (General Use) Se

12、aling and Securing - Clips, End, Strap - Pins, Tent, Metal - Webbing, Textile, Cotton, General Purpose, - Buckles, Tongueless and Web Strap - Lines, Tent - Slips, Tent Line - Cement, Liquid, Tent Patching Natural or in Colors 2 Provided by IHSNot for ResaleNo reproduction or networking permitted wit

13、hout license from IHS-,-,-MIL-T-30368J 83 7999706 O376637 7 I MIL-R-3 390 MIL-C-10799 MIL-F-10884 MIL-V-13811 MIL-G -1 64 91 MIL -R-3 05 O0 MIL-T-43566 MIL-S-437 70 MIL-W-44 049 MIL-C -5 29 50 MIL-T-10168J - Rings, Dee - Cloth, Coated, Cotton, Vinyl Coated, Fire and - Fasteners, Snap - Varnish, Wate

14、rproofing , Electrical, Ignition - Grommet, Metallic - Rope, Polyester - Tape, Textile, Cotton, General Purpose, Natural or in Colors - Snap Hook - Webbing, Textile and Tape, Textile, Mildew Resistant Polypropylene, General Purpose, Natural or in Colors - Crates, Wood, Open and Covered STANDARDS FED

15、ERAL FED-STD-7 51 - Stitches, Seams, and Stitchings MILITARY MIL-STD-105 - Sampling Procedures and Tables for Inspection by Attributes MIL-STD-129 - Marking for Shipment and Storage DRAWINGS U .S e ARMY NAEICK RESEARCH, DEVELOPMENT, AND ENGINEERING CENTER 5-4-181 5-4-182 5-4-183 5-4-184 5-4-185 5-4-

16、186 5-4-187 5-4-188 5-4-296 5-4 -1 2 6 1 - Tent, Prame-Type, Insulated, Sectional, with Floor, 16 X 16, M-1948, Complete; Illustration, Assembly and Views - Floor Units - Arch Segments and Miscellaneous Details - End Blanket Assembly and Details - Door Frame Assembly and Details - Roof Blanket, Guy

17、Band, Vestibule Covers - Vestibule Details - Locking Device and Alternate Threshold - Lighting Unit - Crate for Protection of Arch Ends 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-T-LOLhJ 83 777770b 037bbLB 7 MIL-T-10168J OTHER GOVERNMENT D

18、OCUMENTS Department of the Army Field Manual FM 10-16 - General Repair of Tents, Canvas and Webbing (Copies of documents required by contractors in connection with specific acquisition functions should be obtained from the contracting activity or as directed by the contracting officer,) % 2.2 Other

19、publications. Unless otherwise specified, the following documents of the issue in effect on the date of invitation for bids or request for proposal form a part of this document to the extent specified herein. UNITED STATES DEPARTMENT OF COMMERCE Product Standard PS 1 - Softwood Plywood, Construction

20、 and Industral Commercial Standard CS35 - Hardwood, Plywood (Application for copies should be addressed to the Superintendent of Documents, Government Printing Office, Washington, DC 20402.) NATIONAL FIRE PROTECTION ASSOCIATION (NFPA) National Electrical Code (Application for copies should be addres

21、sed to National Fire Protection Association, Batterymarch Park, Quincy, MA 02269.) UNDERWRITERS LABORATORIES (UL) Standards for Fire and Casualty Hazards (Application for copies should be addressed to Underwriters L3boratories, 333 Pfingsten Road, Northbrook, IL 60062.) AMERICAN SOCIETY FOR TESTING

22、AND MATERIALS (ASTM) A 108 - Standard Quality Cold-Finished Carbon Steel Bars A 513 A 519 - Seamless Carbon and Alloy Steel Mechanical Tubing A 576 A 675 - Mechanical Properties of Special Quality Hot-Wrought Carbon - Electric-Recistance-Welded Carbon and Alloy Steel Mechanical Tubing - Special Qual

23、ity Hot-Wrought: Carbon Steel Bars Steel Bars 4 . Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- MIL-T-LOLbBJ 83 9499906 037bb39 O W - _ MIL-T-1 O1 685 B 633 D 2016 - Standard Test Methods for Moisture Content of Wood E 18 - Electrodeposited Coatin

24、gs of Zinc on Iron and Steel - Rockwell Hardness and Rockwell Superficial Hardness of Metallic Materials (Application for copies should be addressed to the American Society for Testing and Materials, 1916 Race Straii;, Philadelphia, PA 19103.) (Technical society and technical association documents a

25、re generally available for reference from libraries. technical groups and using Federal agencies.) They are also distributed among % 2.3 Order of precedence. In the event of conflict between the text of this document and the references cited herein (except for associated detail specifications, speci

26、fication sheets, or MS standards), the text of this document shall take precedence. Nothing in this document, however, shall supersede applicable laws and regulations unless a specific exemption has been obtained . 3s REQUIREMENTS 3.1 First article. When specified in the contract or purchase order,

27、a sample shall be subjected to first article inspection (see 4.3, 6.2, and 6.4). 3.2 Codes and standards. The tents shall comply with the applicable requirements of UL Standards for Fire and Casualty Hazards and NFPA National Electrical Code, as applicable (see 4.1.1.1.1 and 4.1.1.1.2). 3.3 Material

28、s and components. 3.3.1 Cloth, coated, cotton. The vinyl-coated cotton cloth shall conform to type II, class 1 of MIL-C-10799. The colors shall be Olive Drab 7 and light green (see 3.4.1). * 3.3.2 Tape, textile, cotton. The tape for the wrench containers and for the ties shall be dyed Olive Drab 7 a

29、nd shall conform to type I, class 4, 1 inch and 3/4 inch, respectively, of MIL-T-43566. shall be polypropylene conforming to type I, class 2, Olive Drab 7 of MIL-W-44049 Alternatively, the tape 3.3.3 Webbing, textile, cotton. The webbing shall be dyed Olive Drab 7 and shall conform to type III, clas

30、s 4 of MIL-W-530 as follows: a. For buckle chapes, hook chapes “A“ and “B“ - 1 inch width b. FQr tent section corner reinforcements, roof guy band reinforcements and dee-ring chapes - 1 1/2 inch width. 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-

31、,-_- MIL-T-IOIbJ 83 a 777790b 037bb20 7 W MIL -T -1 O1 6 8J Alternatively, the webbing shall be polypropylene conforming to type III, class 2, Olive Drab 7, of MIL-W-44049. 3.3.4 Thread, polyester. The thread shall conform to type I, class 1, subclass B, shade S-1 (CA 66022) of V-T-285. The dyed thr

32、ead shall show fastness to weathering equal to or better than the standard shade sample (see 6.3). When no standard shade sample is available, the dyed thread shall show good fastness to weathering. Thread sizes shall be as follows: a. For all stitching except stitching indicated by “Z“ on drawings

33、- size FF for needle and bobbin b. For stitching indicated by “Z“ on drawings - size FF for needle, size F for looper 3.3.5 Lines, tent. The tent lines shall conform to type V (for tent line lug) and type XXIV (for guy line) of MIL-L-1709. 3.3.6 Rope, polyester. The polyester rope, 314-inch circumfe

34、rence, shall conform to MIL-R-30500. 3.3.7 Insulation. The insulation material used between the top and bottom floor panels, in the roof and end blankets, including the doors in the end blankets, shall be composed of glass fibers firmly bonded with a thermosetting plastic resin into a resilient mat

35、structure 1 inch thick (4-314, -0 inch tolerance) (see 4.5.1.1) having a weight of 2.1 pounds f 10 percent per 24 square feet. The insulation shall be one continuous piece for each roof blanket and end section (i.e., piecing shall not be permitted). 3.3.7.1 Compressional recovery. The compressional

36、recovery of the material shall be not less than 90 percent when determined in accordance with 4.5.1.2. 3.3.8 Adhesive. The adhesive used in the fabrication of the tent shall conform to type I or type II of MMM-A-181. 3.3.9 Caulking compound. The caulking compound used as a weather seal shall be gray

37、 in color and shall conform to type I of TT-C-598. 3.3.10 Fabric, wire. The wire fabric shall conform to type II, 18 X 16 regular mesh of RR-W-365. 3.3.11 Plastic sheet. The transparent, uncolored plastic sheet for the window panes and transoms shall be made of cellulose acetate butyrate molding mat

38、erial meeting the requirements of L-P-349 for any type or class. The sheet shall be 0.060 f 0.010 inch thick, with polished finish on both sides. 6 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-T-10 16 85 3.3.12 Lumber. The wood used to fabrica

39、te various parts of the tent shall be uniformly dried to a moisture content of 8 to 12 percent at time of fabrication when tested as specified in 4.5.2 and shall be free from shakes, checks, splits, or splintery surface. No more than two sound, tight knots up to 1/2 inch in diameter or not more than

40、 one sound, tight knot from 1/2 to 3/4 inch in diameter will be permitted per square foot. finished on all sides to drawing dimensions. Any of the following species of Boards shall be wood may be used on all parts of Cedar, Port Orford Pine, White Pine, Southern Yellow Pine, Norway or Ponderosa Larc

41、h Hemlock, Western Hickory Maple Chestnut the tent, unless otherwise specified: Douglas Fir Tupelo, Water or Black Sweet Gum (Red Gum) Ash Spruce (Eastern, Sitka) Basswood Oak Cypress Yellow Poplar 3.3.12.1 Exterior laminations. The exterior laminations of the arch segments shall be fabricated from

42、yellow poplar, oak, hickory, ponderosa pine, or white pine. 3.3.12.2 Window assemblies. All wooden parts of the window assemblies shall be fabricated from a species of wood, such as ponderosa or white pine, that will not be susceptible to splintering. 3.3.13 Plywood. The plywood shall be either exte

43、rior type, grade A-C, sanded two sides, in accordance with Product Standard PS 1, or hardwood, type I, grade 2-3, high or medium density face, regular sanded, according to Commercial Standard GS3S (see 2.2). 3.3.14 Grommets, metallic. The grommets shall conform to type III, class 3, size No. 4 and t

44、ype II, class 3, size No. 1 of MIL-G-16491. 3.3.15 Clips, end. The strap end clips shall conform to type I, class 1, size 1 inch of MIL-C-496. 3.3.16 Slips, tent line. The tent line slips shall conform to type II of MIL-S-1734 * 3.3.17 Snaphook, 1 1/4 inch, bolt type. The round eye swivel snaphook s

45、hall conform to dash No. 6-MlZE1 of MIL-S-43770. 7 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-_- - - _- MIL-T-LOL68J 83 W 7777906 O376622 O M MIL-T-1 O1 6 8J 3.3.18 Fasteners, snap. The snap fasteners used on the floor unit wrench retainers shal

46、l conform to style 1, finish 2, reguiar-pronged socket, wood screw base stud, size 1 of MIL-F-10884. 3.3.19 Rings, dee. The dee rings shall conform to class 2 or 3, configuration X, style 1, size 1 by T/8 inch and class 2, configuration H of MIL-R-3390. 3.3.20 Buckle, tongueless, 2 bar. The buckles

47、shall conform te type II, style 1, class 3, size 1-inch of MIL-B-543. 3.3.21 Pins, tent, metal. The tent pins shall conform to type II of MIL-P-501. 8 3.3.22 Wrench, key. The hexagonal key wrenches for operating the rotolock fasteners shall be fabricated as shown on Drawing 5-4-188, from steel confo

48、rming to ASTM A 576 and A 675 and heat-treated to a hardness of 36-44 on the Rockwell C scale (see ASTM E 18). specified for the steel tent pins in MIL-P-501. The key wrench shall be finished as 3.3.23 Chains, safety and footstop. The safety chain shall conform to type II, class 6, steel, trade No.

49、1, and the footstop chain shall conform to type I, grade C, class 5, style 2, 7/64-inch of RR-C-271. * 3.3.24 Buckle, slide, 1 inch with hook. The buckles, fabricated as shown on Drawing 5-4-186, shall be steel, hot-rolled sheet or strip conforming to QQ-S-700. The buckles shall be given a finish conforming to ASTM B 633, followed by bake enameling. The enamel shall conform to type II of TT-E-529. The color