ARMY MIL-STD-1450-1968 LUBRICATION OF FIRE CONTROL INSTRUMENTS《射击控制仪的润滑油》.pdf

《ARMY MIL-STD-1450-1968 LUBRICATION OF FIRE CONTROL INSTRUMENTS《射击控制仪的润滑油》.pdf》由会员分享，可在线阅读，更多相关《ARMY MIL-STD-1450-1968 LUBRICATION OF FIRE CONTROL INSTRUMENTS《射击控制仪的润滑油》.pdf（6页珍藏版）》请在麦多课文档分享上搜索。

1、MILITARY STANDARD LUBRICATION OF FIRE CONTROL INSTRUMENTS Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-STD-II450 II2 m 79777IIII 0075573 4 I MIL-STD-1450 (MU) 2 August 1968 , DEPARTMENT OF DEFENSE Washington, D. C. 20301 Lubrication o Fire Con

2、trol Instruments MIL - STD - 145 O MU) 2 August 1968 1. 2. Recommended corrections, additions or deletions should be addressed to: Commanding Officer, Frankford Arsenal, ATTN: Pennsylvania 19137. This Military Standard is mandatory for use by the Munitions Command SMUFA-N1100, Philadelphia, ii Provi

3、ded by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-CONTENTS iii Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-STD-1450 (MU) 2 August 1968 1. SCOPE 1.1 Purpose.- This standard describes the methods of lu

4、bricating fire control instruments during final assembly or component sub-assembly. 1.2 Classification.- Lubrication shall be in accordance with Method 1 or 2 as designated on the applicable drawing or desgn document. The se- lection of the lubrication method is determined by the nature of the parts

5、, their location and t.he materials, _. as follows: Use Method 1 for - Lubrication of bearing and mating surfaces where degradation of optical, electrical or physical properties of the system may result from contact with the lubricant or its volatile products, or incompatible plastic parts; for lubr

6、ication of certain rubber parts such as 0- rings or other seals. Use Method 2 for - Normal lubrication purposes as applied to gears, bearings and other moving parts, where contamina- tion of a critical optical surface, or an in- compatible plastic or rubber material is con- sidered remote. 1.3 Appli

7、cation.- Lubrication of fire control instruments and equip- ment in accordance with this standard is intended to insure their proper operation under adverse environmental conditions for the maximum possible maintenance-free duration. This standard is intended to cover only general lubrication method

8、s applicable to sliding, rolling, or rotating movements, and rubber seals normally encountered in precision fire control instrument design. It does not cover extremely delicate applications such as watches and clocks; heavy duty mechanisms such as generating units, trailers, etc.; self-lubrieated be

9、arings and special systems utilizing dry-film or powder lubricants. 2. REFERENCED DOCUMENTS 2.1 The following documents, of the issue in effect on date of invi- tation for bids or request for proposal, form a part of this standard to the extent specified herein. SPECIFICATIONS Mi 1 i ta ry MIL-G-434

10、3 MIL-G-23827 Grease, Pneumatic System Grease, Aircraft and Instrument, Gear and Actuator Screw 1 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-STD- 1450 (MU) 2 August 1968 (Copies of specifications, standards and drawings .required by supplier

11、s-. in connection with procurement functions should be obtained from the pw- - -. . _-_ - . curing activity or as directed by the contracting officer.) 3. DEFINITIONS 3.1 Lubricant.- The term lubricant as stated herein applies to specified material used to reduce friction or to aid in assembly. 4. G

12、ENERAL REQUIEMI3MTS This section is not applicable. 5. DETAILED REQUIREMENTS 5.1 Materials.- Lubricants used in fire control instruments and equipment shall be in conformance with MIL-G-4343 or MIL-G-23827 unless otherwise specified on the applicable drawing or design document. 5.2 Lubrication proce

13、dure. 5.2.1 Examination and preparation of mating surfaces. 5.2.1.1 Mating surfaces shall have been examined and determined to be in conformance with the mechanical finish on the applicable drawings and free from surface defects, burrs, ridges, etc. Grease, dirt, corrosion and other foreign substanc

14、es shall be removed using a suitable cleaning procedure, The use of aluminum oxide abrasive cloth is prohibited on bearing surfaces. Bietal parts to be used in optical assemblies shall be cleaned by vapor- phase degreasing wherever possible; where impracticable , solvent soaking, scrubbing and wipin

15、g is permissible. Parts received packaged with a pre- servative or grease other than the lubricants specified in this standard or on the applicable drawing shall be rough cleaned in a separate unit in order to prevent excessive contamination of the cleaning bath. Parts shall be thoroughly dried befo

16、re lubricating using blasts of filtered, clean, dry air, or if available, by heating in a suitably ventilated cir- culating air oven at a temperature not exceeding 100F. mating surfaces by the bare hand shall be avoided. Contact with 5.2.1.1.1 Rubber parts shall have been examined and determined to

17、be free from surface defects, flash, etc. Mold release agents, talc or other foreign substances shall be removed from the rubber surface prior to lu- brication. 5.2.2 Application of lubricant.- Surfaces shall be lubricated in accordance with one of the following methods: 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-