ARMY MIL-S-70615 A (2)-1997 SLINGS TOP-LIFT FAMILY OF SLINGS《家庭全新顶级电梯》.pdf

《ARMY MIL-S-70615 A (2)-1997 SLINGS TOP-LIFT FAMILY OF SLINGS《家庭全新顶级电梯》.pdf》由会员分享，可在线阅读，更多相关《ARMY MIL-S-70615 A (2)-1997 SLINGS TOP-LIFT FAMILY OF SLINGS《家庭全新顶级电梯》.pdf（2页珍藏版）》请在麦多课文档分享上搜索。

1、MIL-S-70bLSA (2) = ob 20bL33b 529 MIL-S-70615A (AR) AMENDMENT 2 15 December 1997 SUPERSEDING AMENDMENT 1 6 August 1996 MILITARY SPECIFICATION SLINGS, TOP-LIFT, FAMILY OF SLINGS This Amendment forms a part of MIL-S-7061 SA(AR), dated 25 January 1991, and is approved for use by the US Army Research, D

2、evelopment and Engineering Center, and is available for use by all Departments and Agencies of the Department of Defense. PAGE 1 2.1.1 SDecifications and standards. Under MILITARY SPECFICATIONS, delete “MIL-A-48078” in its entirety. PAGE 2 Under MILITARY STANDARDS, delete “MIL-STD-105, MIL-STD-109 a

3、nd MIL-STD-1235” in their entirety. PAGE 3 2.1.2 SPECIAL PACKAGING INSTRUCTIONS. Change “P200000332, P200000354, P200000364 and P200000398” as follows: “PAC200000332 3940-01-247-7400, Sling, Multi-leg, Palletized Projectile, Lifting With Instruction Placard PAC200000354 3940-01 -247-3681, Beam, Sing

4、le, Palletized, Projectile, With Instruction Placard PAC200000364 3940-01 -247-3682, Beam, Double, Palletized, Projectile With Instruction Placard 1 of2 FSC 3940 AMSMC N/A DISTRIBUTION STATEMENT A. Approved for public release, distribution is unlimited. Provided by IHSNot for ResaleNo reproduction o

5、r networking permitted without license from IHS-,-,- MIL-S-70bL5A (2) m Ob 2063337 r1b5 MIL-S-70615A (AR) AMENDMENT 2 PAC200000398 1398-01-083-93 13, Sling, Multi-Leg, Top Lift Ammunition With Instruction Placard Change “P200000375, P200000376, and P200000377” to PAC200000375, PAC200000376, and PAC2

6、00000377” respectively. PAGE 6 4.1 Responsibility for insuection. Last sentence (“Reference shall be made . . . . . . .); delete in its entirety. PAGE 11 4.4.1 Inspection lot formation. Third sentence: delete “and complies with the provisions for submission of product as specified in MIL -STD-105”.

7、PAGE 28 4.4.2.1 5 Master Link, 5/8 Stock Diameter; Drawing Number Block, delete “AC200000367” and substitute “ACV200253”. PAGE 31 5.1.1 Level A. Under “Special packaging instructions”, change P200000332, P200000354, P200000364, P200000375, P200000376, and P200000377” to “PAC200000332, PAC200000354,

8、PAC200000364, PAC200000375, PAC200000376, and PAC200000377” respectively. The margins of this amendment are marked with an asterisk or vertical lines to indicate where changes (addition, modifications, corrections, deletions) from the previous amendment were made. This was done as a convenience only

9、 and the Government assumes no liabiliy whatsoever for any inaccuracies in these notations. Bidders and contractors are cautioned to evaiuate the requirements of this document based on the entire content irrespective of the marginal notations and relationship to the last previous amendment. custodian: Army-AR 2 Preparing activity: ArmY-AR (Project 3940-AO16) Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-