ARMY MIL-S-62095 C-1993 SEMITRAILERS TANK GENERAL PURPOSE WATER 7580 AND 15 160 LITERS (2 000 AND 4 000 GALLON) MODIFIED COMMERCIAL《商用改装水箱可装7580升和15160升(2 000和4 000加仑)一般用途的水的半拖车》.pdf

《ARMY MIL-S-62095 C-1993 SEMITRAILERS TANK GENERAL PURPOSE WATER 7580 AND 15 160 LITERS (2 000 AND 4 000 GALLON) MODIFIED COMMERCIAL《商用改装水箱可装7580升和15160升(2 000和4 000加仑)一般用途的水的半拖车》.pdf》由会员分享，可在线阅读，更多相关《ARMY MIL-S-62095 C-1993 SEMITRAILERS TANK GENERAL PURPOSE WATER 7580 AND 15 160 LITERS (2 000 AND 4 000 GALLON) MODIFIED COMMERCIAL《商用改装水箱可装7580升和15160升(2 000和4 000加仑)一般用途的水的半拖车》.pdf（27页珍藏版）》请在麦多课文档分享上搜索。

1、I c MIL-S-b2095C m 999990b Lb9904L 722 m e I Type I - Forced discharge. Type II - Gravity discharge. Size 2 - 7580 L (2,000 gallon), single axle. Size 4 - 15 160 L (4,000 gallon), tandem axle. Class 1 - Uninsulated. Class 2 - Insulated. MIL-S-62095C(AT) 13 Januarv 1993 SUPERSEDING MIL-S-62095B(AT) 1

2、7 July 1987 MILITARY SPECIFICATION SEMITRAILERS, TANK: GENERAL PURPOSE WATER, 7580 AND 15 160 LITERS (2,000 AND 4,000 GALLON), MODIFIED COMMERCIAL This specification is approved for use by the US Army Tank-Automotive Command, Department of the Army, and is available for use by all Departments and Ag

3、encies of the Department of Defense. 1. SCOPE 1.1 Scope. This specification covers 7580 liter (L) (2,000-gallon), single axle and 15 160 L (4,000-gallon), tandem axle, tank type semitrailers for the transportation of nonpotable water. Vehicles procured under this specification are commercial items t

4、hat are required to be warranted by the manufacturer as specified in acquisition documents. 1.2 Classification. The semitrailer shall be one of the following types, sizes and classes, as specified (see 6.2): Beneficial comments (recommendations, additions, deletions) and any pertinent data which may

5、 be of use in improving this document should be addressed to: US Army Tank-Automotive Command, ATTN: AMSTA-UED, Warren, MI 48397-5000, by using the self-addressed Standardization Document Improvement Proposal (DD Form 1426) appearing at the end of this document or by letter. AMSC N/A DISTRIBUTION ST

6、ATEMENT A. Approved or public release; distribution is unlimited. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-S-62095C m 9999906 1699042 669 m MIL-S-62095C(AT) 2. APPLICABLE DOCUMENTS 2.1 Government documents. * 2.1.1 Specifications, standard

7、s, and handbooks. The following specifications, standards, and handbooks form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those listed in the issue of the Department of Defense Index of Specifications and Standards (DODISS) an

8、d supplement thereto, cited in the solicitation (see 6.2). SPECIFICATIONS FEDERAL W-B-131 MIL I TARY MIL-P-514 STANDARDS FEDERAL FED-STD-297 MILITARY * MIL-STD-209 MIL-STD-1223 * * MIL-STD-1474 MIL-STD-1595 MS 51335 MS 75021 - Battery, Storage: Vehicular Ignition Lighting and Starting. - Plates, Ide

9、ntification, Instruction and Marking, Blank. - Rustproofing of Commercial (Nontactical) Vehicles. - Slinging and Tiedown Provisions For Lifting - Nontactical Wheeled Vehicles Treatment, And Tying Down Military Equipment. Painting, Identification Marking and Data Plates Standards. - Noise Limits for

10、Army Materiel. - Qualification of Aircraft, Missile and - Pintle Assembly, Towing, 18,000 Lbs. - Connector, Receptacle, Electrical - 12 Aerospace Fusion Welders. Capacity, Manual Release. Contact, Intervehicular, 28 Volt, Waterproof. * (Unless otherwise indicated, copies of federal and military spec

11、ifications, standards, and handbooks are available from the Naval Publications and Forms Center, Military Specifications and Standards, Bldg. 4D, 700 Robbins Avenue, Philadelphia, PA 19111-5094.) * 2.1.2 Other Government documents, drawings, and publications. The following other Government documents

12、, drawings, and publications form a part of this document to the extent specified herein. Unless otherwise specified, the issues are those cited in the solicitation. 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-lb . PlIL-S-62095C 9999906 1699043

13、 5T5 W * DEPARTMENT OF DEFENSE Department of Defense Index of Specifications and Standards (DODISS). (Copies of the DODISS are available on a yearly subscription basis either from the Government Printing Office for hard copy, or microfiche copies are available from the Director, Navy Publication and

14、 Printing Service Office, 700 Robbins Avenue, Philadelphia, PA 19111-5093.) DEPARTMENT OF TRANSPORTATION (DOT) Federal Motor Carrier Safety Regulations (FMCSR). Federal Motor Vehicle Safety Standards (FMVSS). Regulations Governing Transportation of Dangerous Articles in Tank Motor Vehicles. * (Appli

15、cation for copies of DOT publications should reference the Code of Federal Regulations, 49 CFR, and the Federal Register, and should be addressed to the Superintendent of Documents, U.S. Government Printing Office, Washington, D.C. 20402.) * OCCUPATIONAL SAFETY AND HEALTH ADMINISTRATION (OSHA) Code

16、of Federal Regulations, 29 CFR. (Application for copies of OSHA publications should reference the Code of Federal Regulations, 29 CFR, and the Federal Register and should be addressed to the Superintendent of Documents, U.S. Government Printing Office, Washington, D.C. 20402.) * 2.2 Non-Government p

17、ublications. The following documents form a part of this document to the extent specified herein. Unless otherwise specified, the issues of the documents which are DoD adopted are those listed in the issue of the DODISS cited in the solicitation. Unless otherwise specified, the issues of documents n

18、ot listed in the DODISS are the issues of the documents cited in the solicitation (see 6.2). AMERICAN NATIONAL STANDARDS INSTITUTE, INC. (ANSI) American National Standard Pipe Thread Series. (Application for copies of ANSI publications should be addressed to the American National Standards Institute

19、, 1430 Broadway, New York, NY 10018.) AMERICAN SOCIETY OF MECHANICAL ENGINEERS (ASME) ASME Boiler and Pressure Vessel Code (BPVC) Section IX - Qualification Standard for Welding and Brazing Procedures, Welders, Brazers, and Welding and Brazing Operators. (Application for copies of ASME publications

20、should be addressed to the American Society of Mechanical Engineers, United Engineering Center, 345 East - 47th Street, New York, NY 10017.) 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-S-b2095C m 9999906 Lb99044 431 m MI -6 * AMERICAN WELDI

21、NG SOCIETY (AWS) AWS B2.1 AWS D1.1 - Standard for Welding Procedure and Performance Qualifications. - Structural Welding Code-Steel. (Application for copies of AWS publications should be addressed to the American Welding Society, 2501 N 7th Street, Miami, FL 31025.) * THE EUROPEAN TYFW AND RIM TECHN

22、ICAL ORGANISATION (ETRTO) Standards Manual. (Application for copies of ETRTO publications should be addressed to the European Tyre and Rim Technical Organisation, 32, Avenue Brugmann, 1060 Brussels, Belgium.) 53 18 5350 J551 5560 5682 J700 5702 51292 (Appl icat io SOCIETY OF AUTOMOTIVE ENGINEERS, IN

23、C. (SAE) SAE Standards and Recommended Practices. - Air Brake Gladhand Service (Control) and Emergency (Supply) Line Couplers - Trucks, Truck-Tractors, and Trailers (DoD adopted). Size Engines (DoD Adopted). Measurement of Electromagnetic Radiation (30-1,000 MHZ). - Seven-Conductor Electrical Connec

24、tor for Truck-Trailer Jumper Cable. - Rear Wheel Splash and Stone Throw Protection (DoD Adopted). - Fifth Wheel Kingpin - Commercial Trailers and Semitrailers (DoD Adopted). - Brake and Electrical Connection Locations - Truck-Tractor and Trailer. - Automobile, Truck, Truck-Tractor, Trailer and Motor

25、 Coach Wiring. - Spark Arrester Test Procedure for Medium - Performance Levels and Methods of for copies of SAE publications should be addressed to SAE, Inc., 400 Commonwealth Drive, Warrendale, PA 15096.) THE TIRE AND RIM ASSOCIATION, INC. Year Book. * (Application for copies of Tire and Rim Associ

26、ation publications should be addressed to The Tire and Rim Association, Inc., 175 Montrose West Ave., Copley, OH 44321.) * (Non-Government standards and other publications are normally available from the organizations that prepare or distribute the documents. These documents also may be available in

27、 or through libraries or other informational services.) 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-S-bZ095C = 999990b Lb99045 378 I 3. REQUIREMENTS MIL-S-62095C(AT) * 2.3 Order of precedence. In the event of a conflict between the text of

28、this document and the references cited herein, the text of this document takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. * 3.1 Standard vehicle and accessories. Except as specified in 3.1.1 through 3.1.1.1

29、0.4, the vehicle, components, assemblies, and accessories to be delivered under the contract shall be standard or optional items, sold commercially to the public, which meet or exceed the requirements of this specification. All items shall be as represented and rated in the vehicle manufacturers tec

30、hnical data book. Special bodies or mounted equipment shall be as represented in the body and equipment manufacturers technical data. Technical data shall be limited to specifications and technical material identical to that furnished to the authorized company representatives for selection of vehicl

31、e models and components, and shall be available to the engineering offices of the procuring activity, prior to delivery of the items. The vehicle shall be a standard commercial semitrailer, of a model sold to a significant number of buyers other than the Government, in the course of normal business

32、operations. 3.1.1 Special requirements. In addition to the standard vehicle and components specified in 3.1, the vehicle shall be furnished with special equipment as specified herein. * 3.1.1.1 Treatment and painting. The vehicle shall be treated and painted in accordance with MIL-STD-1223. As speci

33、fied by the procuring activity for the appropriate military service (see 6.2), the exterior color shall be in accordance with MIL-STD-1223. * 3.1.1.2 Marking and data plates. As specified by the procuring activity for the appropriate military service (see 6.2), identification markings and data plate

34、s shall be in accordance with MIL-STD-1223. 3.1.1.3 Rustproofing. The vehicle shall be rustproofed in accordance with FED-STD-297. * 3.1.1.4 Brake lights. At least one pair of brake lights shall override the four-way emergency flasher or the two systems shall be independent of each other. Modificati

35、ons to the manufacturers standard product to accommodate this requirement shall not compromise conformance to any Federal Motor Carrier Safety Regulation referenced herein or to any Federal Motor Vehicle Safety Standard. If additional lights are added to the vehicle, the lights shall be selected fro

36、m the semitrailer manufacturers standard matching hardware. 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-S-62095C m 0b Lb77OYb 204 m * 3.1.1.5 Welders and welding. In addition to the requirements of 3.22.4, all welders employed in the fabric

37、ation of the semitrailer shall be certified, before any welding is accomplished, in accordance with MIL-STD-1595; the welding qualifications of the ASME BPVC, Section IX; or AWS B2.1 or D1.l. The certification that the welders have passed the qualifications test shall be on file at the contractors f

38、acility and shall be available for review by the Government. * 3.1.1.6 Lubrication chart. An illustrated or schematic diagram type lubrication chart shall be provided on the semitrailer. The chart shall direct attention to all lubrication fittings and specify the range and grade of lubricants requir

39、ed for critical temperatures. The chart shall be permanently attached to the semitrailer in a readily visible location. The chart shall be inscribed on a plate conforming to composition A (class 1 or 2) or cornposition C of MIL-P-514. * 3.1.1.7 Lifting and tiedown attachments. When specified (see 6.

40、2), the vehicle shall have lifting and tiedown attachments. Lifting and tiedown attachments shall be in accordance with class 1 and 2 or in accordance with class 3 of MIL-STD-209. Lifting and tiedown attachments shall conform to type II or type III of MIL-STD-209. * 3.1.1.7.1 Tiedown identification.

41、 Tiedown attachments shall be identified by stenciling or other suitable marking. Tiedown markings shall clearly indicate that the attachments are intended for the tiedown of the vehicle on the carrier. * 3.1.1.7.2 Transportation plate. Lifting and tiedown provisions shall include a transportation p

42、late conforming to 3.1.1.8. plate shall have a diagram showing the attachments and proposed lifting slings, the capacity of each attachment, and the required length and size of each sling cable. vehicle showing the center of gravity. The transportation The transportation plate shall have a silhouett

43、e of the * 3.1-1.8 Information plates. The transportation plate specified in 3.1.1.7.2, the sign specified in 3.2.8, the caution plate in 3.16.2.1 and the instruction plate in 3.16.5 shall conform to composition A (class 1 or 2) or composition C of MIL-P-514. * 3.1.1.9 Pintle assembly. When specifie

44、d (see 6.2), a trailer towing package shall be furnished. The trailer towing package shall consist of a pintle, safety chain attachment devices, an electrical receptacle and associated reinforcements and wiring and shall be installed on the rear of the vehicle. The pintle shall conform to MS 51335-2

45、. The pintle shall be installed in the chassis frame with reinforcements to transfer a vertical tongue load of not less than 815 kilograms (kg) (1,800 pounds) and a horizontal drawbar load of not less than 8150 kg (18,000 pounds) directly to the chassis rails. The rearmost portion of the pintle shal

46、l be forward, but 6 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-a MIL-S-62095C U 9999%0b Lb99047 140 no more than 100 millimeters (mm) (four inches) forward, of the rearmost part of the vehicle. The height of the pintle assembly measured from the

47、 ground to the lower inner.jaw of the pintle shall be 787 mm (31 inches) 225 mm (+i - inch) with the semitrailer loaded to its rated payload capacity. * 3.1.1.9.1 Safety chain attachment devices. Two trailer safety chain attachment devices, one adjacent to each side of the pintle, shall be provided.

48、 Each attachment device shall provide an ultimate strength of not less than 8150 kg (18,000 pounds). The attachment devices shall be capable of accommodating a standard grab hook 56 mm (2-3/16 inches) wide, 18.7 mm (47/64 inch) thick and 12.3 mm (31/64-inch) throat width) for a 9.5 mm (3/8-inch) cha

49、in. * 3.1.1.9.2 Electrical receptacle. An electrical receptacle conforming to CAE 5560 with the connectors connected and color coded as specified therein shall be installed near the pintle. spring loaded cover. The receptacle shall be provided with a * 3.1.1.10 24-volt lighting. * 3.1.1.10.1 Independent 24-volt dc system. When specified (see 6.2), a 24-volt direct current (dc) lighting system, independent of the 12-volt dc lighting system, shall be provide