ARMY MIL-S-62052 D-1993 SEMITRAILER VAN AIR TRANSPORTABLE 4990 KILOGRAMS (5 5 TON) AIR CONDITIONED MODIFIED COMMERCIAL《商用改装的有空调的4990公斤(5 5吨)航空运输的客货车半拖车》.pdf

《ARMY MIL-S-62052 D-1993 SEMITRAILER VAN AIR TRANSPORTABLE 4990 KILOGRAMS (5 5 TON) AIR CONDITIONED MODIFIED COMMERCIAL《商用改装的有空调的4990公斤(5 5吨)航空运输的客货车半拖车》.pdf》由会员分享，可在线阅读，更多相关《ARMY MIL-S-62052 D-1993 SEMITRAILER VAN AIR TRANSPORTABLE 4990 KILOGRAMS (5 5 TON) AIR CONDITIONED MODIFIED COMMERCIAL《商用改装的有空调的4990公斤(5 5吨)航空运输的客货车半拖车》.pdf（39页珍藏版）》请在麦多课文档分享上搜索。

1、NOT MEASUREMENT SENSITIVE MIL-S-62052D 23 April 1993 SUPERSEDING MIL-S-62052C(AT) 22 AUGUST 1989 MILITARY SPECIFICATION SEMITRAILER, VAN; AIR TRANSPORTABLE, 4990 KILOGRAMS (5.5 TON), AIR CONDITIONED, MODIFIED COMMERCIAL This specification is approved for use by all Departments and Agencies of the De

2、partment of Defense. 1. SCOPE 1.1 Scope. This specification covers a 4990 kilogram (kg) (5.5 ton) capacity semitrailer equipped with a demountable axle suspension system to enable aircraft loading. The semitrailer is air conditioned and equipped with a single axle. Semitrailers procured under this s

3、pecification are modified commercial items which are required to be warranted by the manufacturer as specified in acquisition documents. 2. APPLICABLE DOCUMENTS 2.1 Government documents. 2.1.1 Specifications standards, and handbooks. The following specifications, standards and handbooks form a part

4、of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those listed in that issue of the Department of Defense Index of Specifications and Standards (DODISS), and supplement thereto, cited in the solicitation (see 6.2). Beneficial comments (rec

5、ommendations, additions, deletions) and any pertinent data which may be of use in improving this document should be addressed to: US Army Tank-Automotive Command ATTN: AMSTA-UED, Warren, MI 48397-5000, by using the self-addressed Standardization Document Improvement Proposal (DD Form 1426) appearing

6、 at the end of this document or by letter. AMSC NIA FSC-2 330 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. I Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-S-62052D = 999990b 1853555 593 MIL-S-62052D SPECIFIC

7、ATIONS FEDERAL * A-A-393 L-F-475 MILITARY MIL-P-5 14 STANDARDS FEDERAL FED-STD-297 MILITARY MIL-STD-171 * MIL-STD-209 - Extinguishers, Fire, Dry-Chemical, - Floor Covering, Vinyl, Surface (Tile and (Hand-Portable). Roll) With Backing. - Plates, Identification, Instruction and Marking, Blank. - Rustp

8、roofing of Commercial Vehicles. - Finishing of Metal and Wood - Slinging and Tiedown Provis Nontactical) Surfaces. ons for Lifting and Tying Down Military Equipment. MIL-STD-1223 - Nontactical Wheeled Vehicles Treatment, Painting, Identification Marking and Data Plate Standards. Aerospace Fusion Wel

9、ders. Fixed Wing Aircraft. * MIL-STD-1595 - Qualification of Aircraft, Missile and MIL-STD-1791 - Designing for Internal Aerial Delivery in (Application for copies of MIL-STD-1791 should be addressed to Wright-Patterson AFB, ASDIENES, Mr. Scott Kuhnen, Wright-Patterson, AFB, OH 45433, telephone (513

10、)255-6281.) * (Unless otherwise indicated, copies of federal and military specifications, standards, and handbooks are available from the Naval Publications and Forma Center, Military Specifications and Standards, Bldg. 4D, 700 Robbins Avenue, Philadelphia, PA 19111-5094.) 2.1.2 Other Government doc

11、uments, drawinga, and publications. The following other Government documents, drawings, and publications form a part of this document to the extent specified herein. the issues are those cited in the solicitation. Unless otherwise specified, DEPARTMENT OF DEFENSE Department of Defense Index of Speci

12、fications and Standards (DODISS). (Copies of the DODISS are available on a yearly subscription basis either from the Government Printing Office for hard copy, or microfiche copies are available from the Director, Navy Publication and printing Service Office, 700 Robbins Avenue, Philadelphia, PA 1911

13、1-5093.) 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-flIL-S-b2052D = 999990b I1853556 42T MIL-S-62052D DEPARTMENT OF TRANSPORTATION (DOT) Federal Motor Carrier Safety Regulations (FMCSR). Federal Motor Vehicle Safety Standards (FMVSS). O * (App

14、lication for copies of DOT publications should reference the Code of Federal Regulations, 49 CFR, and the Federal Register, and should be addressed to the Superintendent of Documents, U.S. Government Printing Office, Washington, D.C. 20402.) AFSC Design Handbook DH-1-11 - Air Transportability Handbo

15、ok. (Application for copies of the AFSC Design Handbook should be addressed to Wright-Patterson AFB, ASD/ENESS, Mr. Rod Wright, Wright-Patterson AFB, OH 45433, telephone (513)255-6281.) * OCCUPATIONAL SAFETY AND HEALTH ADMINISTRATION (OSHA) Code of Federal Regulations, 29 CFR. (Application for copie

16、s of OSHA publications should reference the Code of Federal Regulations, 29 CFR, and the Federal Register and should be addressed to the Superintendent of Documents, U.S. Government Printing Office, Washington, D.C. 20402.) 2.2 Non-Government publications. The following documents form a part of this

17、 specification to the extent specified herein. Unless otherwise specified, the issues of the documents which are DOD adopted are those listed in the issue of the DODISS cited in the solicitation. Unless otherwise specified, the issues of documents not listed in the DODISS are issues of the documents

18、 cited in the solicitation (see 6.2). THE AMERICAN SOCIETY OF MECHANICAL ENGINEERS (ASME) ASME Boiler and Pressure Vessel Code, Section VIII. (Application for copies of ASME publications should be addressed to the American Society of Mechanical Engineers, United Engineering Center, 345 East Forty-Se

19、venth Street, New York, NY 10017.) * AMERICAN WELDING SOCIETY (AWS) AWS 82.1 - Standard for Welding Procedure and AWS D1.l - Structural Welding Code-Steel. Performance Qualifications. (Application for copies of AWS publications should be addressed to the American Welding Society, 2501 NW 7th Street,

20、 Miami, FL 31025.) 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-S-bZ05ZD 999990b 1853557 3bb MIL-S-62052D THE EUROPEAN TYRE AND RIM TECHNICAL ORGANISATION (ETRTO) Standards Manual. (Application for copies of the ETRTO publications should be

21、addressed to the European Tyre and Rim Technical Organisation, 32, Avenue Brugmann, 1060 Brussels, Belgium.) NATIONAL FIRE PROTECTION ASSOCIATION (NFPA) * NFPA 10 - Portable Fire Extinguisher. NFPA 70 - National Electrical Code. * National Fire Protection Association, One Battery March Park, Quincy,

22、 MA 02269-9101.) (Application for copies of NFPA publications should be addressed to SOCIETY OF AUTOMOTIVE ENGINEERS, INC. (SAE) SAE Standards and Recommended Practices 5318 - Air Brake Gladhand Service (Control) and Emergency (Supply) Line Couplers - Trucks, Truck-Tractors, and Trailers (DOD adopte

23、d). 5478 - Slotted and Recessed Head Screws. 5551 - Performance Levels and Methods of Measurement of Electromagnetic Radiation from Vehicles and Devices (30-1000 MHz). 5560 - Seven-Conductor Electrical Connector for Truck-Trailer Jumper Cable. 5682 - Rear Wheel Splash and Stone Throw Protection (DOD

24、 adopted). 5700 - Upper Coupler Kingpin - Commercial Trailers and Semitrailers. 5702 - Brake and Electrical Connection Locations - Truck-Tractor and Truck-Trailer. 51292 - Automobile, Truck, Truck Tractor, Trailer, and Motor Coach Wiring. (Application for copies of SAE publications should be address

25、ed to the Society of Automotive Engineers, Inc., 400 Commonwealth Drive, Warrendale, PA 15096. ) THE TIRE AND RIM ASSOCIATION, INC. Year Book. * be addressed to the Tire and Rim Association, Inc., 175 Montrose West Avenue, Copley, OH 44321.) (Application for copies of Tire and Rim Association public

26、ations should * from the organizations that prepare or distribute the documents. documents also may be available in or through libraries or other informational services.) (Non-Government standards and other publications are normally available These 4 Provided by IHSNot for ResaleNo reproduction or n

27、etworking permitted without license from IHS-,-,-MIL-S-62052D = 9999906 1853558 2T2 = MIL-S-62052D * 2.3 Order of precedence. In the event of a conflict between the text of this document and the references cited herein, the text of this document O - takes precedence. Nothing in this document, howeve

28、r, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS * 3.1 Standard semitrailer, components, and accessories. Except as specified in 3.1.1 through 3.1.1.13, the semitrailer, components, and accessories to be delivered under the contract shall b

29、e the manufacturers standard or optional items, sold commercially to the public, which meet or exceed the requirements of this specification. All items shall be as represented and rated in the manufacturers technical data, including special or mounted equipment. Technical data shall be limited to sp

30、ecifications and technical material identical to that furnished to the authorized company representatives for selection of semitrailer models and components, and shall be available to the engineering offices of the procuring activity prior to delivery of the items. 3.1.1 Special requirements. In add

31、ition to the standard semitrailer and components specified in 3.1, the semitrailer shall be furnished with special equipment as specified herein. * 3.1.1.1 Treatment and painting. The vehicle shall be treated and painted in accordance with MIL-STD-1223. As specified by the procuring activity for the

32、 appropriate military service (see 6.2), the exterior color shall be in accordance with MIL-STD-1223. The body interior color shall be the manufacturers standard gloss white. * 3.1.1.2 Marking and data plates. As specified by the procuring activity for the appropriate military service (see 6.2), ide

33、ntification marking and data plates shall be in accordance with MIL-STD-1223. * 3.1.1.2.1 Instruction plates. Operating instruction plates for at least the following equipment shall be furnished: (a) Electrical circuits controlled by switches (b) Air line outlets (c) Air conditioning controls (d) He

34、ating controls (e) Schematic of interior electrical circuits (f) Schematic of air lines (9) Complete operating instructions for preparing the vehicle for air transport. Instruction plates, schematics, and control devices shall be depicted on photoetched, corrosion-resistant plates. Control device pl

35、ates shall be secured near the control. Instruction and schematic plates shall be located a 5 I I Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-NIL-S-62052D 9999906 1853559 139 MIL-S-62052D on the curbside wall near the electrical distribution boxe

36、s. Operating instructions for preparing near or on the interior of * 3.1.1.3 Rustproofing. with FED-STD-297. * 3.1.1.4 Brake lights. the vehicle for air transport shall be located the curbside door. The vehicle shall be rustproofed in accordance At least one pair of brake lights shall override the f

37、our-way emergency flasher or the two systems shall be independent of each other. Modifications to the manufacturers standard product to accommodate this requirement shall not compromise conformance to any Federal Motor Carrier Safety Regulation referenced herein or to any Federal Motor Vehicle Safet

38、y Standard. If additional lights are added to the vehicle, the lights shall be selected from the semitrailer manufacturers standard matching hardware. * 3.1.1.5 Welders and welding. In addition to the requirements of 3.26.4, all welders employed in the fabrication of the semitrailer shall be certifi

39、ed, before any welding is accomplished, in accordance with MIL-STD-1595; the welding qualifications of the ACME BPVC, Section IX; or AWS B2.1 or D1.l. The certification that the welders have passed the qualifications test shall be on file at the contractors facility and shall be available for review

40、 by the Government. * 3.1.1.6 Lubrication chart. An illustrated or schematic diagram type lubrication chart shall be provided on the semitrailer. The chart shall direct attention to all lubrication fittings and specify the range and grade of lubricants required for critical temperatures. The chart s

41、hall be permanently attached to the semitrailer in a readily visible location. The chart shall be inscribed on a plate conforming to composition A (class 1 or 2) or composition C of MIL-P-514. 3.1.1.7 Wood treatment. Wood shall be treated in accordance with MIL-STD-1223 except interior paneling may

42、be resin impregnated with an overlaid surface on one side of resin treated cellulose fiber and the interior floor may be laminated hardwood in lieu of MIL-STD-1223 treatment. 3.1.1.8 Drain plugs. All drain plugs installed throughout the vehicle for the purpose of draining lubricants shall be of the

43、permanent magnet type. * 3.1.1.9 24-volt lighting. * 3.1.1.9.1 Independent 24-volt dc system. When specified (see 6.2), in addition to the standard 12-volt direct current (dc) lighting system, a 24-volt dc lighting system, independent of the 12-volt dc lighting system, shall be provided. Separate wi

44、ring and bulbs shall be provided for the 24-volt dc system. The system shall conform to 3.13. The 24-volt dc system shall also conform to the Federal Motor Carrier Safety Regulations referenced in 3.13.1, except the 24-volt dc stop and turn lamps shall be combined. 6 Provided by IHSNot for ResaleNo

45、reproduction or networking permitted without license from IHS-,-,-MIL-S-b2052D 9 999990b LB53560 950 9 MIL-S-62052D * 3.1.1.9.2 Interconnected 24-volt dc system. When specified (see 6.2), capability of operating the normal 12-volt dc system from a towing vehicle equipped with a nominal 24-volt dc el

46、ectrical system shall be provided. * 3.1.1.9.3 Receptacle for 24-volt dc system. When either an independent or interconnected 24-volt dc system is specified, the front of the semi- trailer shall also be equipped with a 12-contact receptacle and cover conforming to MS 75021, part number MS 75021-1. T

47、he receptacle shall be located in accordance with CAE J702. The 24-volt dc, 12-contact receptacle shall be connected to the lights as follows: Contact B. Connect to left-hand turn signal and stop lamp (yellow) Contact D. Connect to ground (white) Contact E. Connect to clearance, side marker, identif

48、ication, and tail lamps (black and brown) Contact J. Connect to right-hand turn signal and stop lamp (green). Contact L. Connect to ground (white). The remaining contacts shall not be connected. Circuits B and J on tactical (military design) trucks are combination stop and turn indicator circuits. O

49、n the interconnected 24-volt dc system, the normal 12-volt dc turn signal lights will function both as turn signals and stop lights, and the normal 12-volt dc stop,lights will not be operational when the semitrailer is connected to a towing vehicle with a 24-volt dc power supply. Because of this condition, the stop light (red) circuit is not connected to the 24-vo1t1 12-contact receptacle. * 3.1.1.9.4 Resistors. When an interconnected 24-volt dc system is specifi