ARMY MIL-S-43357 E-1990 SHIRT SLEEPING HEAT RETENTIVE AND MOISTURE RESISTANT NYLON ACETATE TRICOT KNIT《针织尼龙乙酸基吸热防湿睡衣》.pdf

《ARMY MIL-S-43357 E-1990 SHIRT SLEEPING HEAT RETENTIVE AND MOISTURE RESISTANT NYLON ACETATE TRICOT KNIT《针织尼龙乙酸基吸热防湿睡衣》.pdf》由会员分享，可在线阅读，更多相关《ARMY MIL-S-43357 E-1990 SHIRT SLEEPING HEAT RETENTIVE AND MOISTURE RESISTANT NYLON ACETATE TRICOT KNIT《针织尼龙乙酸基吸热防湿睡衣》.pdf（22页珍藏版）》请在麦多课文档分享上搜索。

1、1 INCH-POUND I MIL-S-43357E 28 September 1990 SUPERSEDING MIL-S-43357D 23 November 1983 MILITARY SPECIFICATION SHIRT, SLEEPING, HEAT RETENTIVE AND MOISTURE RESISTANT, NYLON/ACETATE, TRICOT KNIT This specification is approved for use by all Departments and Agencies of the Department of Defense. 1. SC

2、OPE 1.1 Scope, This document covers one type of heat retentive and moisture resistant nylon/acetate, tricot knit sleeping shirt. 1.2 Classification. The shirts shall be of one type in the following sizes as specified (see 6.2). Schedule of sizes XX-Sma 1 1 Sma 1 1 Large X-Small Medium X-Larg e =-La

3、r g e 2, APPLICABLE DOCUMENTS 2.1 Government documents. 2.1.1 Specifications, standards, and handbooks. The following specifications, standards, and handbooks form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these are those listed in the issue of

4、 the Department of Defense Index of Specifications and Standards (DODISS) and supplement thereto, cited in the solicitation (see 6.2). Beneficial comments (recommendations, additions, deletions) and any pertinent data which may be used in improving this document should be addressed to: U.S. Army Nat

5、ick Research, Development, and Engineering Center, Natick, MA 01760-5014, by using the Standardization Document Improvement Proposal (DD Form 1426) appearing at the end of this document or by letter. AMSC N/A FSC 8415 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited.

6、Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SPEC 1FICATI.ONS FEDERAL A-A-50083 - Bag, Plastic, Folded Garment V-F- 106 - Fasteners, Slide, Interlocking V- T- 28 5 - Thread, Polyester DDD-L-20 - Label: For Clothing, Equipage and Tentage, PPP-B-636

7、 - Boxes, Shipping, Fiberboard (General Use) MI LI TARY MIL-S-43357E 84 W 777770b 0455437 b MIL-S-4335 7E I MIL-L-35078 - Loads, Units: Preparation of Semiperishable Subsistence Items; Clothing, Personal Equipment and Equipage; General Specification For * 1 MIL-C-43358 - Cloth, Knitted, Nylon/Acetat

8、e, Tricot, Camouflage 483 STANDARDS FEDERAL FED-STD-191 - Textile Test Methods FED-STD-75 1 - Stitches, Seams and Stitchings MIL I TARY MIL-STD-105 - Sampling Procedures and Tables for Inspection by Attributes MIL-STD-129 - Marking for Shipment and Storage MIL-STD-147 - Palletized Unit Loads MIL-STD

9、-731 - Quality of Wood Members for Containers and Pallets MIL-STD-1491 - Glossary of Knitting Imperfections (Unless otherwise indicated, copies of federal and military specifications, standards, and handbooks are available from the Standardization Documents Order Desk, Building 4D, 700 Robbins Avenu

10、e, Philadelphia, PA 19111-5094.) 2.1.2 Other Government documents. The following other Government documents form a part of this document to the extent specified herein. Unless otherwise specified, the issues shall be those in effect on the date of the solicitation. DEPARTMENT OF THE ARMY FIELD MANUA

11、L FM 10-280 - Mobile Field Laundry, Clothing Exchange, and Bath Operations (Copies of documents required by contractors in connection with specific acquisition functions should be obtained from the contracting activity or as directed by the contracting activity.) 2 Provided by IHSNot for ResaleNo re

12、production or networking permitted without license from IHS-,-,-U.S. Army Natick Research, Development, and Engineering Center Natick Formula IV - Laundering Procedure 2.2 Non-Government publications. The following documents form a part of this document %o the extent specified herein. Unless otherwi

13、se specified, the issues of the documents which are DOD adopted are those listed in the issue of the DODISS cited in the solicitation. Unless otherwise specified, the issues of documents not listed in the DODISS are the issues of the documents cited in the solicitation (see 6,2). COLOR ASSOCIATION O

14、F THE UNITED STATES Department of Defense Standard Shades Color Card for Sewing Threads (Color cards may be available from the Color Association of the United States, 343 Lexington Avenue, New York, NY 10016-0927. If color cards are not available from the Color Association, individual color samples

15、may be obtained from the contracting activity or as directed by the contracting activity.) AMERICAN IRON AND STEEL INSTITUTE (AISI) Type number 304 - Stainless and Heat Resistant Steel Type number 316 - Stainless and Heat Resistant Steel AMERICAN SOCIETY FOR TESTING AND MATERIALS (ASTM) D 3951 - Sta

16、ndard Practice for Commercial Packaging (Application for copies should be addressed to the American Society for Testing and Materials, 1916 Race Street, Philadelphia, PA 19103-1187.) (Non-Government standards and other publications are normally available from the organizations that prepare or distri

17、bute the documents. These documents also may be available in or through libraries or other informational services.) 2.3 Order of precedence. In the event of a conflict between the text of this document and the references cited herein, the text of this document takes precedence. Nothing in this docum

18、ent, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Samples. 3.1.1 Guide sample. Guide samples, when furnished, are solely for guidance and information to the contractor (see 6.4). appear in the sample, in which case the documen

19、t shall govern. Variation from the document may 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-S-43357E 4 W 777970b 0455437 T m . MIL-S-43357E 3.1.2 Standard sample. The finished shirt shall match the standard sample for shade and shall be equ

20、al to or better than the standard sample with respect to all characteristics for which the standard sample is referenced (see 6.4). 3.1.3 First article. When specified (see 6.2), a sample shall be subjected to first article inspection (see 6.3) in accordance with 4.3. 3.2 Material, It is encouraged

21、that recycled material be used when practical as long as it meets the requirements of this specification. 3.2.1 Basic material. The cloth for the body, sleeves, and collar shall be Camouflage Green 483, conforming to MIL-C-43358. 3.2.2 Cuff material, The cloth for the cuffs shall be a true 1 x 1 rib

22、, knit from 2 ply, 100 denier, mudtifilament, semi-dull, normal tenacity nylon yarn. The cloth shall conform to the physical requirements listed in table I when tested as specified in 4.4.1. TABLE I. Physical requirements Weight (oz./sq. yd.) Yarns per inch: Wales Courses Bursting strength (lbs.) 6.

23、5 (min.) 23 (min.) 42 (min.) 150 (min.) 3.2.2.1 Color. The calor of the cloth for the cuffs shall be Camouflage Gr,een 483. 3.2.2.1.1 Matching. The color of the finished cloth shall match the standard sample when viewed under filtered tungsten lamps that approximate artificial daylight and that have

24、 a correlated color temperature of 7500 + 200 K, with illumination of 100 + 20 foot candles, and shall be a good match to the standard sample under incandescent lamplight at 2300 - + 200 K. 3.22.1.2 Colorfastness. The dyed cloth shall show colorfastnkss to launder- ing, perspiration and crocking equ

25、al to or better than the standard sample (see 6.4). When no standard sample is available, the dyed cloth shall show “good“ fastness to laundering and perspiration and shall show a Munsell Value for crocking not lower than.8.S. Testing shall be as specified in 4.4.1. 3.2.2.2 Finish. The dyed cloth sh

26、all be thoroughly scoured, and finished to meet the physical requirements in table I and the shrinkage requirements in 3.2.2.3. 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-S-43357E 3.2.2.3 Shrinkage. The finished cloth shall not shrink or e

27、longate more than 3.0 percent in length and 4.0 percent in width. Testing shall be as specified in 4.4.1. 3.2.3 Thread, polyester. The polyester thread for seaming and stitching shall conform to type I, class 1, size A, AA and B of V-T-285. The thread shall be dyed to match Olive Drab S-1, C.A. 6602

28、2 and shall show fastness to laundering equal to or better than the standard sample (see 6.4). standard sample is available, the dyed gimp shall show “good“ fastness to laundering. Lubrication of the polyester thread by any means in the end item fabricators plant prior to or during sewing is prohibi

29、ted. When no 3,3 Combination size, identification and instruction label. Each shirt shall have a combination size, identification and instruction label conforming to type VI, class 14, of DDD-L-20. Label color shall be Medium Green, cable No, 70034, 70130, or 70131. The fastness to laundering requir

30、ements shall apply. The instructions shall be as follows: a. Fixed Laundry: The sleeping shirt shall be laundered utilizing “Natick Formula IV“. NOTE: DO NOT STARCH, BLEACH, OR PRESS. b. Field Laundry: The sleeping shirt shall be laundered utilizing “Formula II“ of FM 10-280. NOTE: DO NOT STARCH, BL

31、EACH, OR PRESS. c. Drying: The sleeping shirt shall be dried in a tumble-dryer, loaded not more than 2/3 of rated capacity at medium heat cycle (do not exceed 120 F). Remove immediately from dryer. Avoid over-drying. 3.4 Slide fastener. The slide fastener shall be type I, style 3, size LS; short tab

32、 pull, automatic locking, green polyester or green nylon monofilament in a continuous coil or ladder configuration conforming to V-F-106. The slide fastener shall be of sufficient length to accommodate the slide fastener opening indicated by the pattern marks. The tape extension at the top and botto

33、m of the slide fastener shall be not less than 1 inch. The color of the slide fastener tape shall be Olive Green 507 and the color of all other slide fastener components shall approximate the shade of the tape. 3.5 Design. The shirt shall be a long sleeve, pullover type with a collar that converts t

34、o a turtleneck when the front opening slide fastener is closed to the top of the collar (see figure i). 3.6 Patterns. Standard patterns which provide an allowance of 3/8 inch for collar and front and 1/4 inch for all other seams will be furnished by the Government. The Government patterns shall not

35、be altered in any way and are to be used only as a guide for cutting the contractors working patterns. working patterns shall be identical to the Government patterns. The 3.6.1 Pattern parts. Components parts shall be cut from the material speci- fied in table II in accordance with the pattern parts

36、 indicated. 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-S-43357E 84 0b 0455443 8 - MIL-S-4335 7E TABLE II, List of pattern parts Nomenclature of Ma ter ia1 parts e Cut parts Nylon/acetate tricot knit cloth Front Back Sleeves Collar Nylon ri

37、b knit cloth Cuffs 2 3.7 Construction. The construction shall conform in all respects to the requirements specified in table III and herein, Figure 1 is furnished solely for guidance and information. Should variation from the document appear in figure 1, the document shall govern. * .? v)c, E(d reLi

38、 alal coa O al Uv) 4 3 mo 7 CC .-I -4 o0 r,c O 0 4 al C al CI s w c u rd -u U 4 O u4 Lid al4 a4 CO 1v Ua CO b9 rdc, C *-I ME C CO al 4 t cw 2 6) - ac 0 o0 C C o c, -4 9 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-S-4335 7E 4 4 : I I Lr, w w r

39、l n M gI * 4 (d 4 4 O U c VI .rl C .-I EL t c, h.4 e (du o cln Q) au .CC cd(d(d (10 Q ta 7J al -u C cd ln ci C .-# a c 3 O ln C -4 u L a w c 4 (d -I -I O V C 4 f H 5 U 4 (d *c alCi ME I 4 O I 4 .c incorrect; illegible; of improper size, location, sequence, or method of application. Any component mis

40、sing, damaged, or not as specified. Inadequate application of components, such as: Incomplete closure of container flaps, loose strap- ping, improper taping, or inadequate stapling. Bulged or distorted container. Number of unit packs per shipping container is more 9 or less than specified. 4.4.5 Pal

41、letization examination. The fully packaged and palletized end items F shall be examined for the defects listed below. The lot size shall be expressed in units of palletized unit loads. The sample unit shall be one palletized unit lcad, fully packaged. The inspection level shall be S-1 and the AQL, e

42、xpressed in terms of defects per hundred units, shall be 6.5, Exam i ne Defect Finished dimensions Length, width, or height exceeds specified maximum requirement Palletization Pallet pattern not as specified Load not bonded as specified Weight: Exceeds maximum load limits Marking Omitted; incorrect;

43、 illegible; of improper size, location, sequence, or method of application 5. PACKAGING 5.1 Preservation. Preservation shall be level A or Commercial as specified (see 6.2). 5.1.1 Level A preservation. Each shirt shall be folded with fastener closed to bottom of collar to approximate dimensions of 1

44、4-1/2 by 11-1/2 inches and secured with stainless steel (AIS1 type 304) pins, tin or nickel-plated brass pins, aluminum clips or plastic fasteners. Each folded shirt shall be unit packed in a snug-fitting, flat style, clear polyethylene film bag conforming to A-A-50083. 5.1.2 Commercial, The shirts

45、shall be preserved in accordance with ASTM D 3951. 18 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-5.2 Packing. Packing shall be level A, B or Commercial as specified (see 6.2). 5.2,1 Level A packing. Thirty shirts of one size only, preserved as s

46、peci- fied in 5.1, shall be packed in a fiberboard shipping container conforming to style RSC-L, grade VS, of PPP-B-636. The inside of each container shall be fitted with a box liner conforming to type CF, class weather-resistant, variety DW, grade V15c of PPP-B-636, Level A unit packs shall be pack

47、ed flat, front up, collars alternated front to rear two in length, one in width, and fifteen in depth. Inside dimensions of each container shall approximate 23-1/2 inches in length, 15 inches in width, and 15 inches in depth. Approximate dimensions are furnished as a guide only, Each shipping contai

48、ner shall be closed and reinforced in accordance with method III, and waterproofed in accordance with method V of the appendix of PPP-B-636, except that the inspection shall be in accordance with 4.4.4. Shipping containers shall be arranged in unit loads in accordance with MIL-L-35078 for the type a

49、nd class of load specified (see 6.2). - Q Strapping shall be limited to nonmetallic strapping, except for type II, class F loads. 5.2.2 Level B packing. Thirty shirts of one size only, preserved as speci- fied in 5.1, shall be packed in a fiberboard shipping container conforming to style RSC-L, type CF (variety SW) or SF, class domestic, grade 200 of PPP-B-636. The inside of each container shall be fitted with a box liner con