ARMY MIL-S-14630 B-1977 STREAMER SET ATTACHMENT CAMPAIGN AND WAR SERVICE《战役和战争服役饰带套附属物》.pdf

《ARMY MIL-S-14630 B-1977 STREAMER SET ATTACHMENT CAMPAIGN AND WAR SERVICE《战役和战争服役饰带套附属物》.pdf》由会员分享，可在线阅读，更多相关《ARMY MIL-S-14630 B-1977 STREAMER SET ATTACHMENT CAMPAIGN AND WAR SERVICE《战役和战争服役饰带套附属物》.pdf（9页珍藏版）》请在麦多课文档分享上搜索。

1、MILITARY SPE GIZ LCAT IONS - MIL-S-14630B 25 July 1977 a Superseding :. 22 December 1969 MI L-S - 1 4 6 30A STREAMER SET ATTACHMENT, CAMPAIGN AND WAR SERVICE This specification is approved far use by all Departments and Agencies of the Department of Defense. 1. SCOPE 1.1 Scope.- This specification c

2、overs two types of attachments far streamers. 1.2 Classification.- Streamer attachment sets shall be as specified (see 6,2). Type I - 18 Hoke Type LI - 15 Hole .2. APPLICABLE DOCUMENT-S 2.1 Issue of documents.- The following documents of the issue in efect on date of invitation for bids or request f

3、or proposal form a part of this specification to the extent specified -here in. .SPECIFICATIONS FEDERAL QQ-B-613 - Brass, Leaded and Non-Leaded; Flat Products QQ-1-666 - Iron-, Malleable, Ferritic, for Castings Q Q -Nr 2 9 O - Nickel. Plating, .(Elecgrodeposited) PPP-B-636 - Box, Shipping, Fiberboar

4、d PFP-E-66 - Boxes, Setup (Plate, Bar, Sheet and Strip) STANDARQ S . Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-STD-105 - Sampling Procedures and Table for Inspection by Attributes MIL-STD-129 - Marking for Shipment and Storage THE INSTITUTE

5、 OF HERALDRY B-13-3 - Streamer Set Attachment, Campaign War Service (Miniature copy of drawing B-133, identified as figure 1, is attached for information purposes only.) (Copies of specifications, standards and drawings required by contractors in connection with specific procurement functions should

6、 be obtained from the procuring activity or as directed by the contracting officer.) 3. REQUIREMENTS 3.1 First article.- Unless otherwise sDecified (see 6.2) before production is commenced, a sample of the finished attach- ment shall be submitted or made available to the contracting officer or his a

7、uthorized representative for inspect ion and tests as specified in 4.2. The approval of the first article authorizes the commencement of production-but d-oes not relieve the contractor of responsibility for compliance with all applicable provisions of this specification. The first article shall be m

8、anufactured in the same facilities to be used for the manufacture of the product items. 3.2.1 Brass.- Brass for the header shall be sheet or strip conforming to QQ-B-613, annealed temper. I commercial, flat spring quality of .7 - .80 percent carbon (AISIC-1074). 3.3 Design.- The streamer set attachm

9、ent shall consist of a header and eighteen (18) swivel eye snaps- for type I and (15) swivel eye snaps for type II. The design for the type I header shall be as specified on drawing B-13-3. The design of the type II header shall be an exact replica of the design on the Govern- ment furnished hub (se

10、e 3.71, from which the contractors working Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-S-Lq630B 83 7777906 0378787 7 MIL-S-14630B dies shall be extracted. The contractors dies shall be tooled and polished to remove any dents, nicks, scratches

11、 or other imperfections and the unarnmented sections shall be smooth and polished. 3.4 Construction.- The construction of the streamer set attachment shall conform to the requirements specified herein and as shown on drawing B-13-3. The swivel eye spring snaps shall be attached to the header with th

12、e snap spring facing the center of the header, Except for the snap spring the snaps shall be fabricated from iron specified in 3.2.2. The snap spring shall be fabricated from spring steel specified in 3.2.3. The headers shall be made from brass specified in 3.2.1. 3.4.1 Stamping and trimming.- The h

13、eader shall be stamped in a manner to insure a well defined die struck edge and accurately trimmed to the die struck edge. All edges shall be clean, smooth and free from burrs, drag and step. 3.5 Finish.- 3.5.1 Header.- Headers shall be nickel plated. The plating thickness shall be a minimum of 0.00

14、025 inch thick. 3.5.2 Swivel eye spring snap.- The swivel eye spring snap shall be nickel plated with a minimum plating thickness of 0.00025 inch. 3.6 Marking.- In addition to any special marking required by the contract or order see (6.21, the manufacturer shall. stamp his identification mark incon

15、spicuously but legibly on the concave side of the header adjacent to the center hole. 3.7 Government loan property. Hubs for the type 11 header will be loaned by the government and shall be used for making the contractors dies necessary ?or one contract or order. There are no hubs for the type I hea

16、der. It sha? be fabricated in accordance with Drawing B-13-3. 3.8 Workmanship.- The streamer set attachment shall be clean, well made and shaI1 meet the acceptable quality levels established by this specification. 4. QUALITY ASSURANCE PROVISIONS 4.1 Inspection responsibility - Unless otherwise speci

17、fied in the contract or purchase order, the contractor is responsible for the performance of all inspection requirements as specified herein. Except as otherwise specified in the contract or 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-S-L46

18、30B 83 9999906 0378788 O MIL-S-14630B purchase order, the contractor may use his own or any other facilities suitable for the performance of the inspect ion requirements specified herein, unless disapproved by the Government. The Government reserves the right to perform any of the inspections set fo

19、rth in the specification where such inspect ions are deemed necessary to assure supplies and services conform to the prescribed requirements. 4.2 First article inspection.- When a first article is required, inspection of the first article shall be made for all provisions of this specification applic

20、able to the end product examinat ion. 4.3 Sampling for inspection and acceptance.- Sampling for inspection and testing shall be in accordance with the provisions set forth in MIL-STD-105, except where otherwise indicated. 4.3.1 Component testing.- The quality assurance provisions for components and

21、materials, except as otherwise required by this specification, shall be in accordance with applicable specifications and standards referenced herein. When there is a conflict in quality assurance provisions, this specification shall govern. 4.3.2 Certification of compliance.- Components and material

22、s listed below may be accepted on the basis of a contractors certification of compliance for chartacteristics indicated. Component Character ist ic Rqmt para Header Nickel plating and thickness 3.5.1 Swivel eye spring snap Nickel plating 3.5.2 4.3.3 End item examination.- The defects found during ex

23、amination shall be classified in accordance with 4.3.3.1 and 4.3.3.2. The lots shall be inspected in accordance with 4.3.3.3. The sample unit for these examinations shall be one streamer set attachment . 4.3.3.1 Examination of streamer set attachment for visual defects.- Defects so designated by an

24、asterisk (* shall be classified as major when seriously affecting serviceability or appearance and minor when affecting serviceability and appearance but not seriously. 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-S-14630B 83 9797706 0378783

25、 2 M MIL-S-14630B C1 as s i f ic at ion Ex amine Defect Major * Minor Finish of plated surfaces -. . Material and design Construct ion and workmanship Ident if icat ion mark Lng Type of plating not as specified. Plating is not adherent, is not continuous, or is not uniform1 Area of no plating . in f

26、inish, . stains. blistered or otherwise Dirt or foreign matter inbedded Discolored; i.e., spots or Plating is scratched, pitted, impaired . or not polished Unornamented sect ion ncrt smooth Not fabricated of specified Design or Shape altered; i.e, material. does not conform to Government hub or appl

27、icable drawing Signif ieant detail missing, reduced or obliterated. Not eype specified . Any component missing Sharp edge or burr. Drag, step or rough edge . Die struck edge not well defined. Any functioning component that is inoperative or requires undue force to operate. Any forming operation omit

28、ted; e.g. , nat chamfered where required. . out of shape or otherwise impaired Any detail struck ove+, resulting in a double -impression.,. .Missing, illegible or not placed on he concave side . Warped, twis t ed , di-s tort ed , bent I_ _-af the header - - 4.3.3.2 Dimensional examination of streame

29、r set attachment.- Any dimension that is not wi-thin elre specified tolerances shall _. -.x . . be classified .as a defect. 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-S-14630B 4.3.3.3 Inspection levels and acceptable quality levels (AQLs).

30、- The inspection levels and the acceptable q-uality levels (AQLs) expressed in defects per hundred units shall be as follows: Inspect ion For defects applicable to 4.3.3.1 For defects applicable to 4.3.3.2 s- 2 (one class) 4.0 4.3.4 Examination for count of streamer set attachments in intermediate c

31、ontainers.- Streamer set attachments packaged for shipment shall be examined to determine conformance with package markings and specified quantity. The sample unit for this examination shall be one box (interior package), Any box containing less than the specified or marked quantity of streamer set

32、attachments shall be classified as a defect. The inspection level shall be S-2 and the AQL shall be 4.0 defects per hundred units. The lot size shall be the number of intermediate containers. 4.3.5 Examination of preparation for delivery requirements.- An examination shall be made to determine that

33、applicable packaging, packing and marking requirements are complied with. Defects shall be scored in accordance with the list below. The sample unit shall be one shipping container fully prepared for delivery with the exception that it need not be sealed. Defects of closure listed below shall be exa

34、mined on shipping containers fully prepared for delivery. The lot size shall be the number of shipping containers in the end item inspection lot. The inspection level shall be S-2 and the AQL shall be 2.5 defects per hundred units. Examine Defect Marking (exterior and Omitted, incorrect, illegible o

35、r improper size, location sequence, or method of app 1 ic a t ion. Any component damaged, affecting service- ab i 1 ity . such as, incomplete closure of case liners, container flaps, loose strapping, inadequate sealing. Bulging or distortion of containers. Content (exterior Number per container is m

36、ore or less Materials . Any component missing. Workmansh ip Inadequate application of components, and interior) than required. 6 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-e e a - MIL-S-L4630B 3 777770b 0378773 O MIL-S-14630B 5. PREPARATION FOR

37、DELIVERY _- 5.-1 PackagiLg.- Packaging shall be level A or C as specified (see 6.2). 5.1.1 Level A.- Each streamer set attachment, consisting of one header with fifteen, or eighteen swivel eye spring snaps attached, shall be placed irr a snug-fitting, transparent polyethylene bag. The polyethylene f

38、ilm shall be a minimum of 0.0015 inch thick. All seams shall be affected by heat sealing. Prior to or during the heat sealing closure operation excess air within the bag shall be expelled. Each prepackaged attachment shall then be packaged in a snug-fitting Set-up paperboard box conforming to variet

39、y 1, class A or B, style 1 of PPP-B-676. Closure shall be in accordance with the appendix of the box specification. 5.1.2 Level C. Each streamer set attachment shall be packaged to afford adequate protect ion against deterioration and damage from the supply source to the first receiving station. The

40、 supplier may use his standard practice when it meets these requirements. 5.2 Packing.- Packing shall be level A, B, or C as specified (see 6.2). 5.2.1 Level A.- Streamer set attachments packaged as specified in 5.1 shall be packed in a snug - fitting fiberboard box conforming to either class weathe

41、r resistant VS, V3c or V4s of PPP-B-636. Closure shall be in accordance with the appendix of the applicable box specification. The weight of the contents of each shipping container shall not exceed 65 lbs. 5.2.2 Level B.- Streamer set attachments packaged in 5.1, shall be packed in a snug-fitting fi

42、berboard box conforming to class Domestic, grade 275 of PPP-B-636. Closure shall be in accordance with appendix of the container specificat ion. The weight of the contents of each shipping container shall not exceed 65 lbs. 5.2.3. Level C.- The streamer set attachments shall be packed in a manner to

43、 insure carrier acceptance and safe delivery at destination at the lowest transportation rates for such supplies. Containers shall be in accordance with the rules and regulations of the carriers applicable to the mode of transportation. 5.3 Marking.- In addition to any special marking required by th

44、e contract or purchase order, unit packages and shipping containers shall be marked in accordance with MIL-STD-129. . 7 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-S-Lqb30B 3 = 9777906 0378792 2 d MIL-S-14630B 5.3.1 Polyethylene bagged packag

45、es.- Polyethylene bagged packages shall have the required information legibly printed or stamped in b.lack directly an the bag across the center face or on a white paper label inserted within the bag so as to permit ready identification. The white paper label shall contain the following informat ion

46、: STOCK NUMBER NOMENCLATURER S NAME MANUFACTURER S NAME CONTRACT NUMBER 6. NOTES 6.1 Intended use.- The streamer set attachment is intended to be used to display US decoration and campaign streamers. The type I header is to be used for units with over 150 streamers while the type II header is intend

47、ed or use with 150 or less streamers. 6.2 Ordering data.- Procurement documents should specify the following: (a) Ti-tle, number and date of this specification. (b) Type required (see 1.2). (cl When a first artlc-le sample is not required (see 3.1). (d) Marking required (see 3.6). (e) Selection of a

48、pplic-ab-le levels of packaging and packing (see 5.1 and 5.2). Custodians: Prepar ing Act iv i ty : Army - IH Navy - SA The Institute of Heraldry, Air Force - 11 United States Army Review Activities: Navy - M.C . Air Force - 99 DLA - CT Project No. 83450095 - -_ _- . .- ._ 8 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-FIGURE 1 * U. S GOVERNMENT PRIMIN OFFICE 1977-703-0n)/4902 9 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-