ARMY MIL-R-48664 B-1993 RESTRAINT SYSTEMS AMMUNITION (USING BLOW MOLDED PLASTIC DIVIDERS)《军火(使用吹模的塑料圆规)约束系统》.pdf

《ARMY MIL-R-48664 B-1993 RESTRAINT SYSTEMS AMMUNITION (USING BLOW MOLDED PLASTIC DIVIDERS)《军火(使用吹模的塑料圆规)约束系统》.pdf》由会员分享，可在线阅读，更多相关《ARMY MIL-R-48664 B-1993 RESTRAINT SYSTEMS AMMUNITION (USING BLOW MOLDED PLASTIC DIVIDERS)《军火(使用吹模的塑料圆规)约束系统》.pdf（37页珍藏版）》请在麦多课文档分享上搜索。

1、MIL-R-48664B m 9999906 1856550 783 m MIL-R-48664B (AR) 18 March1993 SUPERSEDING MIL-L-48664A (AR) 10 August 1988 MILITARY SPECIFICATION RESTRAINT SYSTEMS, AMMUNITION (USING BLOW MOLDED PLASTIC DIVIDERS) This specification is approved for use by the US Army Armament, Munitions and Chemical Command, a

2、nd is available for use by all Departments and Agencies of the Department of Defense. 1. SCOPE 1.1 Scope. This specification covers the material, requirements, examinations, tests and packaging for a family of blow molded plastic divider racks used for restraining loose: unpalletized 155mm projectil

3、es; unpalletized 8 inch projectiles; or unpalletized, unboxed 120mm mortar rounds contained in fiber tubes during on-vehicle storage and transport (see 6.1). The rack consists of specifically designed plastic dividers that, when assembled, will restrain any conventional projectiles of the 155mm or 8

4、 inch family, or all 120mm mortar rounds in fiber tubes (see 6.4). The loaded racks are restrained in a tactical transport vehicle by means of a cargo tiedown strap(s) applied in an approved manner. The combinations for 155mm or 8 inch are referred to as Loose Projectile Restraint System (LPRS). The

5、 combination for 120mm mortar is referred to as Loose Round Restraint System (LRRS). 2. APPLICABLE DOCUMENTS 2.1 Government documents. 2.1.1 Specifications, standards, and handbooks. The following specifications, standards, and handbooks form a part of this document to the extent specified herein. U

6、nless otherwise specified, the issues of these documents are those listed in the issue of the Department of Defense Index of Specifications and Standards (DODISS) and supplement thereto, cited in the solicitation (see 6.2). Beneficial comments (recommendatiom, additions, deletions) and any ment data

7、 which may be of use in improving this document should be addmaxi to: Commander, U.S. Army ARDEC, ATM: SMCAR-BACS, Picatimy Arsenal, New Jmey 078-5 by Upng tbe self-addnssed standardization Documcnt improvement Propasai (DD Fomi 1426) appearing at the end of this document or by letter. mc2590 AMSC N

8、/A -STATEMENT distribution is unlimited. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-flIL-R-48bb4B m 999790b L85b551r bLT m MIL-R-48664B (AR) SPECIFICATIONS MIL I TARY MIL-A-48078 - Ammunition, Standard Quality Assurance Provisions, General Speci

9、fication for MIL-A-70625 - Automated Acceptance Inspection Equipment for Non-Electronic Components, Design, Testing and Approval of STANDARDS FEDERAL FED-STD-595 - Color MILITARY MIL-STD-109 - Quality Assurance Terms and Definitions MIL-STD-129 - Marking for Shipment and Storage HANDBOOKS MILITARY M

10、IL-HDBK-728/6 - Military Handbook, Ultrasonic Testing (Unless otherwise indicated, copies of federal and military specifications, standards and handbooks are available from DODSSP- Customer Service, Standardization Documents Order Desk, 700 Robbins Avenue, Bldg. 4D, Philadelphia, PA 19111-5094.) 2.1

11、.2 Other Government documents, drawinqs and publications. The following other Government documents, drawings and publications form a part of this document to the extent specified herein. Unless otherwise specified, the issues are those in cited in the solicitation. 2 Provided by IHSNot for ResaleNo

12、reproduction or networking permitted without license from IHS-,-,-MIL-R-48bb4B W Ob LBSb552 55b W MIL-R-48664B (AR) DRAWINGS ARMY MATERIEL COMMAND 9207909 9210140 9215220 9216352 9235999 9287993 12577501 12577502 12577503 12577504 AC200000400 AC200000401 AC200000402 AC200000403 AC200000404 - Project

13、ile B-inch, M106HE, LAP Assy - Projectile 8-inch, M509A1 ICM, LAP Assy - Projectile 155mm, M483A1 DPICM, LAP Assy - Projectile 155mm, M107 HE, LAP Assy - Projectile 155mm, M549A1 HE RAP, LAP Assy - Projectile, 8-inch, M650 RAP, LAP Assy - Cartridge 120mm, HE, M934 - Cartridge 120mm, Smoke, M929 - Ca

14、rtridge 120mm, Illum., M930 - Cartridge 120mm, HE, M933 - Combination of Adapted Items, Loose Projectile Restraint System, 155mm - Rack, Ammunition, 15 Round Assy, Loose Projectile Restraint System, 155mm - Divider, Short, Loose Projectile Restraint System, 155mm - Divider, Long, Loose Projectile Re

15、straint System, 155mm - Packaging Drawing, Loose Projectile Restraint System, 155mm 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-R-48bb4B 9999706 l185b553 492 = AC200000405 AC200000408 AC200000438 AC200000571 AC200000572 AC200000573 AC200000

16、574 AC200000591 AC200000596 AC200000597 AC200000598 AC200000599 TECHNICAL MANUALS MILITARY MIL-R-48664B (AR) O - Test, Ease of Disassembly, Loose - Material for Divider, Ammunition, Loose Projectile Restraint System, 155m Projectile Restraint System - Divider, Ammunition, Loose Projectile Restraint

17、System, 8-inch (203mm) - Combination of Adapted Items, Loose Projectile Restraint System, 8-in (203mm) - Rack, Ammunition, 9 Round Assy, Loose Projectile Restraint System, 8-in (203mm) - Packaging Drawing, Loose Projectile Restraint System, 8-inch (203mm) - Test, Ease of Disassembly, Loose Projectil

18、e Restraint System, 8-inch (203mm) - Divider, Ammunition, Loose Round Restraint System (LRRS), 120mm Mortar - Combination of Adapted Items, Loose Round Restraint System (LRRS), 120mm Mortar Rds in Fiber Tubes O - Rack, Ammunition, 36 Round Assy, LRRS, 120m Mortar Rds in Fiber Tubes - Packaging Drawi

19、ng, Rack, Ammunition, 36 Rd Assy, LRRS, 120mm Mortar - Test, Ease of Disassembly, Loose Round Restraint System (LRRS) 120m Mortar TM 9-2590-210-10 - Operators Manual: Loose Projectile Restraint System (LPRS) for use with Field Artillery Companion Vehicles (Copies of other Government documents, drawi

20、ngs and publications required by contractors in connection with specific acquisition functions should be obtained from the contracting activity or as directed by the contracting activity.) 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-NIL-R-48bb4

21、B W 9999906 L85b554 329 H MIL-R-48664B (AR) 2.2 Order of precedence. In the event of a conflict between the text of this document and the references cited herein, the text of this document takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specif

22、ic exemption has been obtained. 3. REQUIREMENTS 3.1 Materials. The materials used in the manufacture of the applicable divider(s), ammunition, shall be as specified on Dwg AC200000408. Certification of compliance shall be provided by the contractor. 3.2 Dividers. Parts and assemblies shall comply wi

23、th all requirements specified on the applicable drawings and with all requirements specified in the applicable specifications. 3.2.1 Flatness. When new and in a relaxed position laid flat on a side, the sides of a divider shall be straight within 1/8 inch from a 24 inch straight edge placed at any l

24、ocation other than over the stacking lugs. 3.2.2 Weld cones. Weld cones shall be homogeneously welded together at the plane of the mold parting line to provide maximum strength to the divider as intended by design. 3.2.3 Drainaue holes. Drainage will be provided for any moisture accumulated within t

25、he divider interior when the dividers are assembled on either edge. matching any of the following colors of Federal Standard 595: -34052, -34079, -34086, -34087, -34096, or -34102. To retard sun degradation, ultraviolet stabilizer shall be added into the color concentrate. Certification shall be pro

26、vided by the contractor to assure that the ultraviolet stabilizer added into the color concentrate consists of 0.3 percent Tinuvin 770 and 0.05 percent Igranox 1076 based on a 4.0 percent color letdown. 3.2.4 Color. The color of the divider shall be olive drab 3.2.5 Stackina luqs. Dividers when laid

27、 flat and stacked, will nest on their stacking lugs without space between dividers. This nesting is required in any flat position, i.e., open slots pointing in the same direction or alternating directions, NSN up or down. The vertical sides of the stack shall align within + 1/8 inch. Different lengt

28、hs of dividers are not intermixed for this requirement (see 4.5.6). 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-R-48664B = 9999906 1856555 265 MIL-R-48664B (AR) 3.3 Performance test. The following defects shall not be permitted on the teste

29、d assemblies: a. Failure of the rack by deforming, splitting or breaking, which allows the dividers to disengage and spill the projectiles/rounds during the performance tests. b. Separating of the parting line seam more than 2.5 inches along the top edge of the divider in contact with the projectile

30、s/rounds. This failure shall not result in a collapse of the divider walls below the next structural stiffener; either handle, hand grip or weld cone. c. Any breaking or cracking of the rack other than at the parting line seam (see 3.3.b.) during the performance tests. Punctures, abrasions and wear

31、though caused by the restraint strap metal parts or projectile grommets are not counted as a failure, providing such wear does not lead to functional failure of the dividers or rack assembly. d. Excessive bending of the short sections at the corners of an assembled rack loaded with projectiles/round

32、s and restrained to a vehicle side wall by a cargo strap on three sides of the rack per TM 9-2590-210-10 or other applicable restraint publication. Excessive bending is deformation which allows the restraint strap(s) to disengage from the strap slot allowing the rack assembly to radically shift or u

33、pset during the performance tests (see 4.5.1.2.). e. Deformation of a divider which interferes with ease of disassembly (see 4.5.5). f. Failure of disassembled dividers to be reassembled into a load bearing rack for successful continuation of the performance test. 3.4 Divider markinas. The divider d

34、esign shall include a thirteen digit (plus three dashes) National Stock Number (NSN) molded in a recessed manner in each divider in 3/8 inch characters by 1/16 inch deep on one side only. The divider design shall include a material designator code and year (last 2 digits) the divider was manufacture

35、d molded in a recessed manner in each divider in 1/4 characters by 1/32 deep on one side only. The divider design shall include the contract number molded in a recessed manner in 6 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-R-48bb4B = 9Ob 18

36、56556 LTL MIL-R-48664B (AR) each divider in 1/4 characters by 1/32 deep on the opposite side from and same location as the NSN. See drawing AC200000408 for material designator. See applicable part drawing for location of markings. 3.5 Ease of assembly and disassembly. The divider slots shall be so c

37、onstructed to permit ease of assembly and disassembly yet the assembled divider rack must be rigid enough to maintain its original configuration while loaded. The loaded rack configuration is evaluated by a performance test (see 4.5.1) and extreme operating temperature tests (see 4.5.4). Ease of dis

38、assembly is tested as specified in 4.5.5. 3.6 Extreme operatinq temperatures. The rack, ammunition, must restrain the applicable ammunition load at temperatures from minus 60 degrees Fahrenheit to plus 145 degrees Fahrenheit (see 4.5.4), as evidenced by meeting the performance test requirements of 3

39、.3. 3.7 Process controls. The contractors quality program plan or detailed inspection plan shall include documented process controls which detail the specific procedures involved in the manufacture of the plastic dividers. These documented process controls shall be submitted to the contracting offic

40、er for review and approval by the cognizant technical agency (CTA) in accordance with the approved DID specified on the Contract Data Requirements List (CRDL) in the contract (see 6.3). The contractor shall not initiate production without written approval from the contracting officer. Once approved,

41、 the contractor shall not change the process without written approval from the contracting officer. The documented process controls shall include the following information as a minimum: a. Item nomenclature b. Applicable component (divider) c. List of applicable drawings and specifications d. List o

42、f inspection equipment e. List of materials and suppliers f. Process flow charts 7 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-flIL-R-48bb4B 999990b 1856557 038 MIL-R-48664B (AR) g. Methods for controlling (and documenting) operational parameters

43、 of process (examples; temperature, pressure, feed times, rate of mold closure). h. Procedure for mixing virgin resin material and reground material and method for identifying these batches or continuous flow. 3.8 First article. When specified in the contract or purchase order (see 6.2), a sample sh

44、all be subjected to first article inspection in accordance with the technical provisions herein (see 4.3). 3.9 Workmanship. The dividers shall be regular, relatively smooth and free from wrinkles and rough spots to the extent that minor irregularities shall not interfere with successful testing unde

45、r 4.5.5. Critical areas are within and adjacent to the assembly slots. The dividers shall be free from cracks, pinholes and any other defects that might affect serviceability and durability. Flashing at the parting lines shall not exceed 1/16 inch height on external perimeters and 1/32 inch height a

46、t the handles (if applicable). Flashing in the open slots shall be removed uniformly to meet tolerances of the open slot. Clean up shall include breaking of sharp corners. All dividers shall be free of chips, dirt, grease and foreign material. If cleaning agents are used, the method shall not be inj

47、urious to the divider material nor shall any of the dividers be contaminated by the cleaning agents. 4. QUALITY ASSURANCE PROVISIONS 4.1 Responsibilitv for inspection. Unless otherwise specified in the contract or purchase order, the contractor is responsible for the performance of all inspection re

48、quirements (examinations and tests) as specified herein. Except as otherwise specified in the contract or purchase order, the contractor may use his own or any other facilities suitable for the performance of the inspection requirements specified herein, unless disapproved by the Government. The Gov

49、ernment reserves the right to perform any of the inspections set forth in this specification where such inspections are deemed necessary to ensure supplies and services conform to prescribed requirements. 4.1.1 Responsibilitv for compliance. All items must meet ail requirements of Sections 3 and 5. The inspection set forth in this 8 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-