ARMY MIL-R-14864-1970 RANGE FINDER LASER AN VVA-1《AN VVA-1型激光测距仪》.pdf

《ARMY MIL-R-14864-1970 RANGE FINDER LASER AN VVA-1《AN VVA-1型激光测距仪》.pdf》由会员分享，可在线阅读，更多相关《ARMY MIL-R-14864-1970 RANGE FINDER LASER AN VVA-1《AN VVA-1型激光测距仪》.pdf（20页珍藏版）》请在麦多课文档分享上搜索。

1、MIL-R-i4864(MU) 2 March 1970 MILITAET SPECIFICATION RANGE EINDEE, LASER: AN/WS-1 WAFLNING - EYE HAZARD EXTREME CAUTION MUST BE EXERCISED IN OPEPATING AND TESTING THE RANGE FINDER. IF THE LASER LIGHT BEAM ENTERS THE HUMAN EYE, THE RETINA OF THE JBX CAN BE BURNED. THE HIGH ENERGY DENSITY OF THE BEAM C

2、AN ALSO PRODUCE SUCH DAMAGE AT EXTREME RANGE AND BY REFLECTION FROM ANY SHINY SURFACE SUCH AS GLASS, MEXAL, PAINT, ETC. IN VIEW OF THE POSSIBILITY OF PRODUCING SEEOUS EYE DAMAGE THE RANGE FINDER SHOULD NOT BE OPERATED UNLESS THE TARGEX ARFA HAS BEEN EVACUATED. 1. SCOPE 1.1 This specification covers

3、one type of range finder designated as Laser Range Finder AN/WS-l (see 6.1). 2. APPLICABLE DOCUMENTS 2.1 The f011017ir1g documents, of the issue in effect on date of invitation for bids or request for proposal, form a part of this speci- fication to the extent specified herein. SPECIFICATIONS Milita

4、ry MIL -F -13926 Fire Control Materiel: General Specification Governing the Manufacture and Inspection of Parts, Equipment and Tools for Army Materiel: Packaging and Packaging of Inspection Equipment , Supply and Maintenance of Laser: 10559281 MIL -P -14232 MIL-I -45607 MIL -R-i4865 Receiver-Transmi

5、tter, MIL-C -14866 Control, Power Supply: 10559261 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL -i4864 (MU) Indicator, Command, Display: 105 5 9201 STANDARDS Ni lit a ry ing Proaeduries and Tables for ectPon.%y Att ribt es Quality Assurance ,T

6、 and Definitions Environmental Test . . I. ,: F105 5 9401 Finde S -1 PACKAGING DATA SHEET io55g1;ai (Copies of specifications, standard required by suppliers ia connection with specific procurement functions should be obtained from the procuring activity or as directed by the contracting officer ,)

7、3. ZEQIREBENTS 3.1 Fabrication .- The range finder shall be manufactured in accordance with Drawing F10559401 and drawings pertaining thereto. The following components a.nd cables shall each have met the requirements of their detailed specifications and drawings, respectively, prior to assembly as a

8、 range finder. (a) Receiver-Transmitter, Laser: 10559281 - MIL-R-l4865(MU) (b) Control, Power Supply: 10559261 - mL-C-i4866() (c) Control, Gunners, Laser Ranging: 10559221 - MIL-C-l4867(MU) (d) Indicator, Digital. Display: 10559241 - MIL-I -1.4868() 2 Provided by IHSNot for ResaleNo reproduction or

9、networking permitted without license from IHS-,-,-MIL -R -14864 (MU) (e) (f) Cable, Interconnect - 6wi: i0559286 (g) Cable, Interconnect - 673: 10559288 (h) Cable, Interconnect - 6114: 10559289 (i) Cable, Interconnect - 6w5: 10559290 Indicator, Command Display: 10559201 - MIL-I -14869() 3.2 General

10、specification.- The range finder shall meet the folloving requirements, where applicable, of KL-F-13926: (a) Order of precedence (b) Dimensions and tolerances (e) Inorganic protective surface finishes 3.3 Performance.- 3.3.1 Range finder operation +60 to +90F,- The range finder shall meet the-requir

11、ements of 3.3.1.1 through 3.3.1.15 when thermally stabilized within the temperature raxge of 40F to +90F and when the loads, power, and signals of Table I are applied as specified. TABLE I ITEM 1. 1.1 1.2 1.3 1.4 1.5 l. 0 1 *7 1.8 1.9 1.10 1.11 1.12 1.13 C ONDIT1 ON Loads : Resi s t o r Resistor Re

12、sis t or Res 5 E: or Resistor Resistor Re sis t or Resistor Re si s t or Re si s t or Resistor Resistor Resistor CHARACTERISTICS 300 ohms .t- 5% 300 chms f 5$ 300 ohms -+ 5$ 300 ohms -+ 5$ 300 ohms +. 5$ 300 ohms f 5$ 300 ohms $: 5% 300 ohms f 5$ 300 ohms k 5% 300 ohms f 5% 300 ohms f 5% 240 ohms +.

13、 5% 620 ohms f 5$ CONNECTIONS Connected to the following pins of 645 cable with re- turn to P2-T: P2 -A P2 -B P2-c P2 -D P2 -E P2 -F P2 -G P2 -H P2 -J P2 4s P2 -L P2 -P P2 -R 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-TABLE I (continued) - ITZ

14、M 2. 2.1 3. 3 -1 3 -2 4. 4.1 - CONDITION Power sources: 24 Vdc Signal sources : Laser On Gunners Control Aului lia ry Equipment : Cable CHARACTERI STECS Tolerance: 2 Vdc 24 f2 Vdc 24 f2 vac CONNECTPIONS Connected between f oilowi ng tem nals : 6w4P3( t) and 64P4( -) Applied to .- Pressing the RANGE

15、6utton when it is flashing (ranging) shall cause the PF“ to discharge through the flashtube turn off during ranging and turn on steady after ranging, indicating that the puise forming network (PFN) is recharged. Pressing the RANGE button after ranging vhen the red light is steady shall not affect th

16、e flashtube. the red light on the RANGE button to flash and the range return selector LAST indicator lamp shall light, The flashing red light on the RANGE button shall When the PF“ is charged, pressing the RESET button shall cause 3.3.1-3 Target selection.- (a) Pressing the “1“ or “2“ range return s

17、elector button shall cause the range of the first or second target, respectively, to be displayed on the nixie tubes. returns, pressing the LAST range return selector button shall cause the range to the last target to be displayed. target returns, pressing the LAST range return selector button shall

18、 cause the range to the third target to be displayed. When the FEED button is pressed, the GO (green) lamp shall light. When the Laser Mode Control switch is in the TEST position, the GO lamp shall light except during the following conditions when the SELECT lamp shall light: pressed and more than t

19、wo target echoes are received. depressed. depressed and four or more target echoes are received. the maximum range. selector shall be inactivated and it shall be impossible to interrupt this connection except by pressing the RESE2 button. When there are ne, two, or three target When there are four o

20、r more (b) (e) - (i) When the range return selector “I“ button is de- (2) When the range return selector “2“ button Is (3) ;hen the range return selector LAST button is (4) When the target range is equal to or greater than When the green indicator light is on, the range return (d) 3.3.1.4 RESITC swi

21、tch.- Whenever the RFSET button is pressed, the rznge return nixie indicator shall read zero, the four range nixie indica- tors shall read zero, and the green or yellow indicator light shall 8180 turn off 3.3.1.5 LASER MODE CONTROL siitch.- 3.3 1.5.1 TEST position.- Pressing the WGE button when it i

22、s flashing shall not discharge the PFN through %he flashtube. the requlrenaents of 3.3.1.3 shall apply. In addition, Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-3.3.1.5.2 ON position.- When the laser mode control switch is in the ON position, aft

23、er ranging,the SELECT lamp shall light. FED button shall cause the GO lamp to light. Pressing the 3.3.1.5.3 AWO position.- When the laser mode control switch is in the AUTO position, after ranging, the GO lamp shall light, When no echoes are received the SELECT lamp shall light. 3.3.1.6 3.3.1,6 .i M

24、inimum range, maximum range, ranging accuracy, and range Ranging - lacer firing. - resolution II - Minimum range, maximum range, ranging accuracy, and range resolutix shall be as specified Fn MIL-R-14865. 3.3.1.6 2 PLnimum time between ranging. - The requirements for minimm time between sanging shal

25、l be as specified in 1a-14865, 3.3.1 6.3 Maximum sustained ranging.- The maximum number of rangings oha.11 be as specified in MIL-R-14865. 3.3.1.6.4 Remote ranging.- The requirements for remote ranging shall be as specified in mL-R-14865. 5.3.1.7 Events counter,- The events counter shall perform as

26、specified in MIL-R-14865. 3.3.1.8 Input voltage variation.- The range finder shall meet the rsnging accuracy specified in 3.3.1.6.1 when the input voltage of the prime power source varies between +i8 Vdc and +3O Vdc, 3.3.19 Maximum power drain.- The direct current drain from the prime power source s

27、hall be less than 12 amperes at any time. 3.3.1.10 Primary po wer transient.- The range indicator readout shall not change under the following conditions: (a) (b) When the input voltage is dropped to a value of 6 volts When the input voltage is increased to 90 volts for a or less for a duration of a

28、t least 100 milliseconds. duration of 100 milliseconds. 3.3.1.11 Peak output power.- The peak optical power output shall be as specified in MIL-R-14865, 3.3.1.12 Malfunction indication.- 3.3.1.12.1 Overvoltage.- If an overvoltage condition occurs in the i“ circuitry, the numbers “O“ and “6“ shall ap

29、pear on the fourth range counter nixie indicator and the MALF lamp shall light. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-R-LYbY 12 U 779970b 04bY775 5 U - _,- NIL-R-i4864 (MU) 3.3.1.12.2 “A“ trigger and couner.- If a malfunction occurs in

30、the reply gating or counter circuit card, the numbers “O“, “7“, and “8“, respectively, shall appear on the fourth range counter nixie indTcator and the 1aLF lamp shall light, 3.3.1.12.3 Command signal line (to computer).- If a malfunction occurs in the command signal line to the computer, the number

31、s “O“ and “9“ shall appear on the fourth range counter nixie indicator and the MALF lamp shall light. 3.3.1.13 Data line (to computer).- All data line signals to the conputer shall be as specified in mL-R-14865. 3.3.1.14 Command signal output (to computer).- The boresight and command signals fed to

32、the computer shall be as specified in MTL-R-14865. 3.3.2 Environmental.- 3.3.2.1 Storage temperature.- The ran e finder shall. meet the require- ments of 3.3.1.3 Cexcept subparagraph (c)(4)5 , 3.3.1.6.1 (maximum range only), and 3.3.1.11 at ambient temperature (oF to gOF) after exposure and thermal

33、stabilization at -80 and +160F. 3.3.2.2 Operating temperature.- The range finder shall meet the requirements of 3.3.1.3 except subparagraph (c)(4), 3.3.1.6.1, 3 3.1.8, 7.3.1.10, and 3.3.1.11 while exposed to and themlly s6abilized at -40F and +l25F, subsequent to which it shall meet the requirements

34、 of 3.3.1.3 except subparagraph (c)(b), 3.3.1.6.1 (maximum range only, and 3.3.1.11 at ambient temperature ( 60F to 90QF). 3.3.2.3 Vibration.- The range finder shall meet the requirements of 3.3.1.3 except Subparagraph (c) (4)l nd shall have no physical failure during the following vibratory exposur

35、e: (a) Amplitude: .5 inch maximum (b) Acceleration: 4 g.maxmum (c) Crossover frequency: 12.5 hertz (Hz) (d) Sweep time: 5 to 500 to 5 Hz in i$ minutes. firo sweeps in each of three mutually perpendicuar axes. Subsequent to the vibration exposure, the range finder shall meet the requirements of 3.3 -

36、1.6. (maximum range only) and 3.3. i. 11. 3 3.3 Final. performance. - Aftea. exposure to the environmental conditions of 3.3.2, the range finder shall meet the requirements of 3.3.1.1 through 3.3.1.14, except 3.3.1.3 (c)(4) and 3.3.1.13, 8 Provided by IHSNot for ResaleNo reproduction or networking p

37、ermitted without license from IHS-,-,-4. QALIm ASSURANCE PROVISIONS 4.1 Responsibility for inspection.- Unless otherwise specified in the contract or purchase order, the supplier is responsible for the per- formance of all inspection requirements as specified. herein. Except as otherwise specified,

38、the supplier may utilize his own or any other facilities suitable for the performance of the inspection requirements specified herein, unless disapproved by the Government. perform any of the inspections set forth in the specification where such inspections are deemed necessary to assure supplies an

39、d services conform to prescribed requirements. The Government reserves the right to 4.1.1 General provisions. - The component and subassembly inspection requirements of MIL-F-13926 form a part of the quality assurance provisions of this specification. Definitdons of inspection terms shall be as list

40、ed j.n MIL-STD -log. 4.2 First article (initial production) approval.- The requirement for first article approval and the responsibility (Government or contractor) for first article testing shall be as specified in the contract. The sample for first article approval tests shall consist of three (3)

41、range finders. The sample shall be manufactured in the same manner, using the same materials, equipment, processes, and procedures as used in regular production. All parts and materials, including packaging and packing, shall be obtained from the same source of supply as used in regular production.

42、4.2.1 Government testing. - When the Government is responsible for conducting first article approval tests, the contractor, prior to sub- mitting the sample to the Government, shall inspect the.sample to insure that it conforms to all the requirements of the contract and submit a record of this insp

43、ection with the sample, including certificates of conformance for materials. 4.2.2 Contractor testing.- When the contractor is responsible for conducting first article approval tests, the sample shall be inspected by the contractor for all the requirements-of the contract. and a record of this inspe

44、ction, including certificates of conformance for materials, shall be submitted to the Government for approval. The Government reserves the right to witness the contractors inspection, The sample 4.3 Inspection provisions. - 4.3.1 Submission of product.- Unless otherwise specified by the contracting

45、officer, inspeckion lot size, lot formation and presentation of lots shall be in accordance with “Submission of Product“ provisions of MIL -sm -105 . 9 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-flIL-R-14b4 12 m 77777Ob 04b4777 7 m EIIL -R -1486

46、4 (MU) 4.3.2 Examination and tests.- 4.3 2.1 Components and subassemblies. - AU. components and sub- i:ssemblies shall be inspected. in accordance with the inspection provisions contained in Supplementary Quality Assurance Provisions (SQAP) listed in the technical data package (TDP). applice.ble Qua

47、lity Assurance Provisions of mL-F-13926 shall apply. In the absence of SQAPs, the 4.3.2.2 Functional tests.- The requirements and tests of Table II shall be inspected on a LOO percent basis. All examinations and tests shall be conducted at the standard ambient temperature (COOF to 9O0F) TABLE II USE

48、 103 PERCENT INSPECTION TEST CHARACTERISTfC REQREMENT PROCEDURE 101 102 103 i04 105 i06 107 i08 109 113 111 112 113 114 Turn-on condition 3.3.1.1 PFN charge and la.ser firing 3.3.1.2 Target selection 3 .-3 .1.3 RESET switch 3.3.1.4 LASER MODE CONTROL switch . 3.3.1.5 Ranging - laser firing 3.3.1.6 E

49、vents counter 3-3.1.7 Input voltage variation 3.3.1.8 Maximum pover drain 3.3.1.9 Primary power transient 3.3.1.10 Peak out put power 3.3.1 11 Malfunction indication 3.3.1.12 Data line (to computer) 3.3.1.13 Command signal output (to computer) 3.3.1 14 4.6.1.1 4.6.i.2 4.6.1.3 4.6.1.4 IC. 6.1.5 4.6.1.6 4.67 4.6.1.8 4.6.1.9 4,6 .i .io 4.6 .i .i1 4.6.1.12 4.6 .i .i3 4.6.1 .i4 4.3.P.3 Fin