ARMY MIL-PRF-63033 C-2009 MANUALS TECHNICAL DEMILITARIZATION OF SURPLUS MILITARY ITEMS PREPARATION OF《技术手册 准备废除多余的军备》.pdf

《ARMY MIL-PRF-63033 C-2009 MANUALS TECHNICAL DEMILITARIZATION OF SURPLUS MILITARY ITEMS PREPARATION OF《技术手册 准备废除多余的军备》.pdf》由会员分享，可在线阅读，更多相关《ARMY MIL-PRF-63033 C-2009 MANUALS TECHNICAL DEMILITARIZATION OF SURPLUS MILITARY ITEMS PREPARATION OF《技术手册 准备废除多余的军备》.pdf（26页珍藏版）》请在麦多课文档分享上搜索。

1、NOT MEASUREMENT SENSITIVE MIL-PRF-63033C (TM) 18 May 2009 SUPERSEDING MIL-PRF-63033B (TM) 10 August 2006 PERFORMANCE SPECIFICATION MANUALS, TECHNICAL: DEMILITARIZATION OF SURPLUS MILITARY ITEMS, PREPARATION OF This specification is approved for use by the Department of the Army and is available for

2、use by all departments and agencies of the Department of Defense. Comments, suggestions, or questions on this document should be addressed to: Commander, USAMC Logistics Support Activity, Acquisition Logistics Center, ATTN: AMXLS-AP, Redstone Arsenal, AL 35898-7466 or e-mailed to: tmssffilogsa.redst

3、one.armv.mil. Since contact information can change, you may want to verify the currency of this address information using the ASSIST Online database at http:/assist.daps.dla.mil/. AMSC 9065 AREA TMSS DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. Provided by IHSNot

4、 for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-63033C(TM) This page intentionally left blank. 11 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-63033C(TM) TABLE OF CONTENTS Section Page 1. SCOPE 1 1.1

5、 Scope2. APPLICABLE DOCUMENTS 1 2.1 General2.2 Government documents2.2.1 Specifications, standards, and handbooks 1 2.2.2 Other Government documents and publications2.3 Non-Government publications 1 2.4 Order of precedence 2 3. REQUIREMENTS3.1.1 Style and format3.1.2 National Stock Numbers (NSN) and

6、 part numbers 2 3.1.3 Level of coverage 2 3.1.3.1 Abbreviations and acronyms3.1.3.2 Equipment names and nomenclature 2 3.1.4 Illustrations3.1.5 Referencing3.1.6 Manual size3.1.6.1 Pocket TM 3 3.1.6.2 Horizontal TM3.1.6.3 Font size3.1.6.4 Foldout/foldup pages3.1.7 Security classification markings 3 3

7、.2.1 Front matter 3.2.1.1 Front cover 3.2.1.1.1 Title 3 3.2.1.1.2 Notices 3.2.1.1.2.1 Supersedure notice (for revisions only) 3 3.2.1.1.2.2 Distribution statement 4 3.2.1.1.2.3 Export warning control statement 4 3.2.1.1.2.4 Destruction Notice 3.2.1.2 Warning summary 3.2.1.3 Change transmittal page 3

8、.2.1.4 List of Effective Pages/Work Packages 4 3.2.1.5 Title block page 4 3.2.1.6 Table of contents3.2.2 General Information work package 4 3.2.2.1 Work package metadata 4 3.2.2.2 Work Package Identification Information 4 3.2.2.3 Scope 4 3.2.2.4 Authorization 5 3.2.2.5 Certification 3.2.2.6 Reportin

9、g demilitarization 5 in Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-63033C(TM) TABLE OF CONTENTS Section Page 3.2.2.7 Special information 5 3.2.3 Methods of Demilitarization Work Package 5 3.2.3.1 Work package metadata 3.2.3.2 Work Packag

10、e Identification Information 6 3.2.3.3 Initial Setup Information 6 3.2.3.4 Descriptive methods of demilitarization 6 3.2.3.5 Procedural methods of demilitarization 3.2.4 Detailed instructions for Demilitarization Work Package 6 3.2.4.1 Work package metadata 6 3.2.4.2 Work Package Identification Info

11、rmation 6 3.2.4.3 Initial Setup Information 3.2.4.4 Procedures 3.2.5 References Work Package 6 3.2.5.1 Work package metadata 3.2.5.2 Work Package Identification Information 6 3.2.5.3 Initial Setup Information 3.2.5.4 Scope 6 3.2.5.5 Publication list 7 3.2.6 Rear Matter 3.2.6.1 Glossary 3.2.6.2 Alpha

12、betical index 3.2.6.3 Authentication page 7 3.2.6.4 Recommended Changes to Publications and Bland Forms DA Form 2028 7 3.2.6.5 Foldout pages 3.2.6.6 Back cover 4. VERIFICATION4.1 Verification5. PACKAGING 7 5.1 Packaging6. NOTES 8 6.1 Intended use 8 6.2 Acquisition requirements 8 6.3 Technical Manual

13、s (TMs)6.4 Definitions6.4.1 Contracting activity6.4.2 Warning6.5 Subject term (keyword) listing 8 6.6 Changes from previous issueIV Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-63033C(TM) TABLE OF CONTENTS Section Page CONTENT/FORMAT SELEC

14、TION MATRIX FOR DEMILITARIZATION OF SURPLUS MILITARY ITEMS, PREPARATION OF 15 A.1 GENERAL 1A.l.l ScopeA. 1.2 Application ; 15 A. 1.3 Tailoring. The contracting activity should evaluate the individual requirements of this specification to determine the extent to which they are most suitable for the a

15、cquisition and modify the requirements to ensure that each achieves the optimal balance between operational needs and cost 15 A. 1.4 Explanation of columns 1A.2 APPLICABLE DOCUMENTSv Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-63033C(TM)

16、This page intentionally left blank. VI Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-63033C(TM) 1. SCOPE 1.1 Scope. This specification contains the requirements for the preparation of technical manuals (TMs) for demilitarization of surplus

17、military items. 2. APPLICABLE DOCUMENTS. 2.1 General. The documents listed in this section are specified in Section 3 of this specification. This section does not include documents cited in other sections of this specification or recommended for additional information or as examples. While every eff

18、ort has been made to ensure the completeness of this list, document users are cautioned that they must meet all specified requirements documents cited in Section 3 of this specification, whether or not they are listed. 2.2 Government documents. 2.2.1 Specifications, standards, and handbooks. The fol

19、lowing specifications, standards, and handbooks form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. STANDARDS DEPARTMENT OF DEFENSE MIL-STD-4005I-2 Preparation of Digital Technical Inf

20、ormation for Page-Based Technical Manuals HANDBOOKS DEPARTMENT OF DEFENSE MIL-HDBK-2361 - Army Digital Publications Development Implementation Guide (Copies of the above standards are available online at http:/assist.daps.dla.mil/ or from the Standardization Document Order Desk, 700 Robbins Avenue,

21、Building 4D, Philadelphia, PA 19111-5094.) 2.2.2 Other Government documents and publications. The following other Government documents and publications form a part of this document to the extent specified herein. Unless specified otherwise, the issues are those cited in the solicitation or contract.

22、 _DOD 5230.24 Distribution Statements on Technical Documents (Copies of DoD documents are available at http:/www.dtic.mil/whs/directives/.) 2.3 Non-Government publications. The following documents form a part of this document to the extent specified herein. Unless otherwise specified, the issues of

23、these documents are those cited in the solicitation or contract. 1 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-63033C(TM) AMERICAN SOCIETY OF MECHANICAL ENGINEERS ASMEY14.38 Abbreviations and Acronyms (Application for copies should be add

24、ressed to the American Society of Mechanical Engineers, 3 Park Avenue, New York, NY 10016-5990.) 2.4 Order of precedence. Unless otherwise noted herein or in the contract, in the event of a conflict between the text of this document and the references cited herein, the text of this document takes pr

25、ecedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 General. 3.1.1 Style and format. Unless otherwise specified herein, the general style and format of a TM for demilitarization of surplus military

26、 items shall be prepared in accordance with MIL-STD-40051-2. 3.1.2 National Stock Numbers (NSN1 and part numbers. NSNs shall not be used in the procedures or the narrative portion of the TM. Unless essential for identification, manufacturers part numbers shall not be used in procedures or the narrat

27、ive portion of the TM. 3.1.3 Level of coverage. The information provided in the TM for demilitarization of surplus military items shall be directed to the least experienced personnel expected to use it. The reading grade level shall be the level specified by the contracting activity and in accordanc

28、e with MIL-STD-40051-2 (see 6.2). 3.1.3.1 Abbreviations and acronyms. Abbreviations used throughout the manual shall be in accordance with ASME Y 14.38. Use of acronyms shall be consistent throughout the TM, but shall be held to a minimum. The first use of an abbreviation or acronym shall be spelled

29、 out completely with the abbreviation or acronym in parentheses immediately after the word(s). 3.1.3.2 Equipment names and nomenclature. Only approved names, nomenclature, and common names shall be used. Terms, names, and nomenclature shall be used consistently throughout the TM. 3.1.4 Illustrations

30、. Unless otherwise specified by the contracting activity (see 6.2), only line drawings shall be used. Illustrations shall be placed as close to their reference in text as possible. Illustrations may float on a page to reduce the white space on a page. Whenever possible, place illustrations on the sa

31、me or facing page of associated text. Foldout illustrations shall not be included in work packages. They shall be the last printed matter of the manual or volume. 3.1.5 Referencing. Reference to other documents and information within the TM shall be held to a minimum. Reference shall not be made to

32、other documents unless they are normally available to the user. If reference to other documents is necessary, reference shall be to the publication number only. Reference made within the TM shall include the necessary location data only. 3.1.6 Manual size. TMs shall be prepared in the size selected

33、from Table 1 as specified by the contracting activity (see 6.2). The maximum printing area shall include all printed matter including publication and page numbers. 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-63033C(TM) Table I. Manual s

34、izes (in inches). Style Pocket Logbook Standard Double Standard Trim Size 4x5-1/2 5-1/2x4 6-1/2x9-1/2 9-1/2x6-1/2 8-1/2x11 11 x 8-1/2 17x11 Format Vertical Horizontal Vertical Horizontal Vertical Horizontal Horizontal Only Maximum Printing Area 3-3/8x5-1/4 5-1/4x3-3/8 5-51/6x8-3/4 8-3/4x5-5/16 7x10

35、10x7 15-1/2x9 3.1.6.1 Pocket TM. Pocket TM numbers shall appear on the front and back cover only. Page numbers shall appear on lower, outer edges of each page. 3.1.6.2 Horizontal TM. Unless otherwise specified by the contracting activity (see 6.2), TMs prepared in horizontal format shall be printed

36、head to foot with holes punched at the bottom of even numbered pages and at the top of odd numbered pages. Except for pocket TMs, the TM number shall appear on the upper right corner of all pages. The upper pages shall have even numbers, and the lower pages shall have odd numbers. 3.1.6.3 Font size.

37、 Except for pocket size TMs, font size shall be no smaller than 8 point. 3.1.6.4 Foldout/foldup pages. Foldout/foldup pages shall not be used. 3.1.7 Security classification markings. Security classification markings, if applicable, shall be applied in accordance with MIL-STD-40051-2. 3.2 Content . T

38、he TM for demilitarization of surplus military items shall consist of the following: a. Front matter b. General Information Work Package c. Methods of Demilitarization Work Package d. Detailed Instructions for Demilitarization Work Package e. References Work Package f. Rear Matter 3.2.1 Front matter

39、 . Unless otherwise specified by the contracting activity (see 6.2), the front matter shall consist of the following described information. 3.2.1.1 Front cover . Unless specified in the following, the front cover shall be prepared in accordance with MIL-STD-40051-2. For format, see FIGURE I. 3.2.1.1

40、.1 Title . The title shall be “Demilitarization Procedures for (insert name of item to be demilitarized).1 3.2.1.1.2 Notices . The following notices shall appear as specified. Notices shall not be boxed. 3.2.1.1.2.1 Supersedure notice (for revisions only) . When a TM is revised, a supersedure notice

41、 shall be included and an asterisk (*) shall prefix the supersedure notice and the TM number. 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-63033C(TM) 3.2.1.1.2.2 Distribution statement . A TM prepared to the specification shall include a

42、 distribution statement provided by the acquiring activity and taken from those provided in Department of Defense Directive (DoDD) 5230.24. 3.2.1.1.2.3 Export warning control statement . All TMs detailing modifications to equipment or other assets under the purview of the Export Control Act as amend

43、ed (22 U.S.C. 2778 et seq.) and meeting the requirements of DoDD 5230.25 shall contain the following export control notice. “WARNING - This document contains technical data whose export is restricted by the Arms Export Control Act (Title 22, U.S.C, Sec 2751, et. seq.) or the Export Administration Ac

44、t of 1979, as amended, Title 50A, U.S.C, App. Violations of these export laws are subject to severe criminal penalties. Disseminate in accordance with provisions of DoDD 5230.25.“ 3.2.1.1.2.4 Destruction Notice . All TMs with a distribution statement “B“ through “F“ or “X“ shall contain the followin

45、g destruction notice: “HANDLING AND DESTRUCTION NOTICE - Comply with distribution statement and destroy by any method that will prevent disclosure of contents or reconstruction of this document.“ 3.2.1.2 Warning summary . A warning summary, in accordance with MIL-STD-40051-2, shall appear on the fir

46、st right-hand page immediately after the front cover. See FIGURE 2 for an example of a warning summary. 3.2.1.3 Chanfie transmittal page . A change transmittal page, in accordance with MIL-STD-40051-2, shall be included when the TM is changed. 3.2.1.4 List of Effective Pages/Work Packages . A list o

47、f effective pages/work packages in accordance with MIL-STD-40051-2 shall be included. 3.2.1.5 Title block page . The title block shall be prepared in accordance with MIL-STD-40051-2. For format, see FIGURE 3. 3.2.1.6 Table of contents. The Table of Contents shall begin on the first right-hand page f

48、ollowing the title block page. The table of contents shall be prepared in accordance with MIL-STD-40051 -2. See FIGURE 4 for an example of a Table of Contents. 3.2.2 General Information work package . The General Information work package shall consist of information as described in the following par

49、agraphs (as required). 3.2.2.1 Work package metadata . Work package metadata may be included (see MIL-HDBK-2361). 3.2.2.2 Work Package Identification Information . Work package identification information is required for this work package. 3.2.2.3 Scope . The scope paragraph shall contain the following statement: “This manual