ARMY MIL-PRF-46795 H-2009 GENERATING SYSTEM ALTERNATOR RECTIFIER 60 AMPERES 28 VOLTS《发电系统 60安培28伏特的整流器交流发电机》.pdf

《ARMY MIL-PRF-46795 H-2009 GENERATING SYSTEM ALTERNATOR RECTIFIER 60 AMPERES 28 VOLTS《发电系统 60安培28伏特的整流器交流发电机》.pdf》由会员分享，可在线阅读，更多相关《ARMY MIL-PRF-46795 H-2009 GENERATING SYSTEM ALTERNATOR RECTIFIER 60 AMPERES 28 VOLTS《发电系统 60安培28伏特的整流器交流发电机》.pdf（21页珍藏版）》请在麦多课文档分享上搜索。

1、Comments, suggestions, or questions on this document should be addressed to U.S. Army RDECOM, Tank Automotive Research, Development and Engineering Center, ATTN: RDTA-EN/STND/TRANS MS #268, 6501 E. 11 Mile Road, Warren, MI 48397-5000 or emailed to DAMI_STANDARDIZATIONconus.army.mil. Since contact in

2、formation can change, you may want to verify the currency of this address information using the ASSIST Online database at http:/assist.daps.dla.mil. AMSC N/A FSC 2920 NOT MEASUREMENT SENSITIVE MIL-PRF-46795H 29 October 2009 SUPERSEDING MIL-PRF-46795G 29 August 1997 PERFORMANCE SPECIFICATION GENERATI

3、NG SYSTEM: ALTERNATOR, RECTIFIER, 60 AMPERES, 28 VOLTS This specification is approved for use by all Departments and Agencies of the Department of Defense. 1. SCOPE 1.1 Scope. This specification covers 28 volts (V), direct current (dc) generating systems, engine driven through belt or direct connect

4、ion, to provide 60 amperes (A) for charging and operating loads. The system consists of a rotating field alternator with integral diode rectifier and adjustable voltage regulator in a single housing. This specification also covers repair parts for this system. 2. APPLICABLE DOCUMENTS 2.1 General. Th

5、e documents listed in this section are specified in sections 3 and 4 of this specification. This section does not include documents cited in other sections of this specification or recommended for additional information or as examples. While every effort has been made to ensure the completeness of t

6、his list, document users are cautioned that they must meet all specified requirement documents cited in sections 3 and 4 of this specification, whether or not they are listed. 2.2 Government documents. 2.2.1 Specifications, standards, and handbooks. The following specifications, standards, and handb

7、ooks form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract (see 6.2). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-46795H 2 ST

8、ANDARDS DEPARTMENT OF DEFENSE STANDARDS MIL-STD-461 - Requirements for the Control of Electromagnetic Interference Characteristics of Subsystems and Equipment. MIL-STD-810 - Environmental Test Methods and Engineering Guidelines. MIL-STD-889 - Dissimilar Metals MIL-STD-1275 - Characteristics of 28 Vo

9、lt DC Electrical Systems in Military Vehicles. (Unless otherwise indicated, copies of the above specifications, standards, and handbooks are available from the Document Automation and Production Service, Building 4/D, 700 Robbins Avenue, Philadelphia, PA 19111-5094 or website: http:/assist.daps.dla.

10、mil/quicksearch/.) 2.2.2 Other Government documents, drawings, and publications. The following other Government documents, drawings, and publications form a part of this document to the extent specified herein. Unless otherwise specified, the issues are those cited in the solicitation or contract (s

11、ee 6.2). DRAWINGS DEPARTMENT OF DEFENSE 10929868 - Rectified AC Generating System (Interface). (Copies of these drawings are available from the U.S. Army Tank-automotive and Armaments Command, ATTN: RDTA-EN, 6501 E. 11 Mile Rd, Warren, MI 48397-5000.) NUCLEAR REGULATORY COMMISSION (NRC) Code of Fede

12、ral Regulations (CFR) - Title 10, Parts 30 and 40. (Copies of the Code of Federal Regulations (CFR) are available from the Superintendent of Documents, U.S. Government Printing Office, 732 North Capitol St. NW, Washington, DC 20402 or website: http:/www.gpoaccess.gov/cfr/.) Provided by IHSNot for Re

13、saleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-46795H 3 2.3 Non-Government publications. The following documents form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitatio

14、n or contract (see 6.2). AMERICAN SOCIETY FOR TESTING AND MATERIALS (ASTM) ASTM B117 - Standard Practice for Operating Salt Spray (Fog) Apparatus (DoD Adopted). (Application for copies should be addressed to the American Society for Testing and Materials (ASTM), 100 Barr Harbor Drive, West Conshohoc

15、ken, PA 19428-2959 or website: http:/www.astm.org.) 2.4 Order of precedence. In the event of a conflict between the text of this document and the references cited herein, the text of this document takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless

16、a specific exemption has been obtained. 3. REQUIREMENTS 3.1 First article. When specified (see 6.2), samples shall be subjected to first article inspection in accordance with 4.3. 3.2 Materials. Materials used shall be in accordance with the manufacturers materials specifications for this type of it

17、em. The material shall be free of defects which adversely affect appearance, performance, or serviceability of the finished product (see 4.6.1). 3.2.1 Recycled, recovered, or environmentally preferable materials. Recycled, recovered, or environmentally preferable materials should be used to the maxi

18、mum extent possible provided that the material meets or exceeds the operational and maintenance requirements, and promotes economically advantageous life cycle costs (see 4.6.1). 3.2.2 Prohibited material. Asbestos, cadmium, and radioactive materials shall not be used in this item. Radioactive mater

19、ial is defined by Title 10, CFR, Parts 30 and 40, and other radioactive material in which the specific activity is greater than 0.002 microcuries per gram or the activity per item equals or exceeds 0.01 microcuries (see 4.6.1). 3.2.3 Pure tin. The use of pure tin is prohibited. Tin content used in c

20、onnector materials shall not exceed 97 percent, and an alloy material shall be chosen to inhibit the growth of tin whiskers (see 6.4.4). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-46795H 4 3.2.4 Dissimilar metals. When dissimilar metals

21、are used in intimate contact with each other, protection against electrolysis and corrosion shall be provided. Dissimilar metals such as brass, copper or steel (except corrosion-resisting steel) passivated in accordance with SAE-AMS-2700 shall not be used in intimate contact with aluminum or aluminu

22、m alloy. Protective measures for dissimilar metals shall be in accordance with MIL-STD-889. 3.3 Design and construction. Generating system shall conform to the envelope dimensions, the mechanical mounting interfaces, and the electrical mounting interfaces as shown in drawing 10929868, and applicable

23、 specifications and standards (see 4.6.1). 3.3.1 Interchangeability. Generating system and all component parts shall be physically and functionally interchangeable with all other such parts of the same part number previously furnished under this specification (see 4.6.2). 3.3.2 Polarity. Generating

24、systems shall be designed to operate in negatively grounded electrical circuit (see 4.6.2). 3.3.3 Standard parts. Military standard parts shall be incorporated whenever possible. Commercial standard parts may be used, provided they are interchangeable with military standard parts without modificatio

25、n and meet the requirements and verifications within this document (see 4.6.1). 3.4 Performance. 3.4.1 Electromagnetic interference characteristics. Conducted and radiated emissions from the generating system shall conform to requirements specified in figures 1 and 2 (see 4.7). 3.4.2 Voltage. Genera

26、ting system shall provide steady state voltage at any setting between 26 volts direct current (Vdc) and 30 Vdc when mechanically and electrically installed and operated as intended (see 4.8). 3.4.2.1 Voltage adjustment. Generating system shall provide means to adjust voltage output between 26 Vdc an

27、d 30 Vdc (see 4.8.1). 3.4.2.2 Voltage regulation. Generating system, when output voltage is adjusted as in intended use, shall maintain set voltage (see 6.4.1) within + 0.5 Vdc. Generating system shall return to set voltage within 0.6 second (s) of any load change (see 4.8.2). 3.4.2.3 Transient volt

28、age characteristics. Generating system shall meet the requirements of MIL-STD-1275 regarding ripple, surges, spikes, and starting disturbances in fault-free, single fault, and multi-fault conditions (see 4.8.3). Provided by IHSNot for ResaleNo reproduction or networking permitted without license fro

29、m IHS-,-,-MIL-PRF-46795H 5 1 0 K 1 0 0 K 1M 1 0 M 1 0 0 M 1G 1 0 G 1 0 0 GLimit Level (dBV)Fr e que nc y (H z)305070901 1 0NO MI NA L E UT LI MI TS O U RCE R E LA X AT I O NV O L TAG E( A C & DC)2 8 V BAS I C C URV E1 1 5 V 6 dB2 2 0 V 9 dB2 7 0 V 1 0 dB4 4 0 V 1 2 dBB A S I C C U R V E94FIGURE 1. C

30、onducted emissions levels. 1 0 K 1 0 0 K 1M 1 0 M 1 0 0 M 1G 1 0 G 1 0 0 G010305070901 1 0Limit Level(dBV/m)Fre qu e ncy (Hz )24448969NAVYFIXED& AFNAVYMOBILE &ARMYFIGURE 2. Radiated emissions levels. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MI

31、L-PRF-46795H 6 3.4.3 Maximum current (rated output). Generating system shall supply 60 A current under maximum load at 10 000 revolutions per minute (rpm) alternator rotor shaft speed (see 4.9). 3.4.3.1 Non-operating current. Generating system shall exhibit non-operating current through ignition swi

32、tch circuit of not more than 300 milliamperes (mA). Further, with ignition switch open, non-operating current from battery shall be not more than 25 mA (see 4.9.2). 3.4.4 Endurance. Generating system shall maintain set voltage (see 3.4.2.2) during operation under various conditions of rotor shaft po

33、sition, speed, and current load. There shall be no servicing, adjustment, nor replacement of parts (see 4.10). 3.4.5 Overspeed. Generating system shall operate at 12 000 rpm under not more than 5 A load without impairing electrical or mechanical performance (see 4.11). 3.4.6 High temperature operati

34、on. Generating system shall maintain set voltage output + 0.2 Vdc during operation in ambient air temperature of 250 degrees Fahrenheit (F) (121 degrees Celsius (C). Subsequently, system shall conform to 3.4.3 (see 4.12). 3.4.7 Low temperature operation. Generating system shall maintain set voltage

35、output + 0.5 Vdc during operation in ambient air temperature of minus (-) 65F (-54C). Subsequently, system shall conform to 3.4.3 (see 4.13). 3.4.8 Shock. After testing in accordance with 4.14, generating system shall meet the requirements of 3.4.2 and 3.4.3. 3.4.9 Vibration. During testing in accor

36、dance with 4.15, generating system shall maintain set voltage output + 0.5 Vdc. After testing in accordance with 4.15, the generating system shall meet the requirements of 3.4.4. 3.4.10 Submersion. Generating system shall operate during submersion in a salt-water solution. Current from battery shall

37、 not exceed 10 A. Subsequently, voltage regulator compartment shall contain not more than 10 cubic centimeters (cm3) of salt-water solution, and the system shall meet the requirements of 3.4.2 and 3.4.3 (see 4.16). 3.4.11 Fungus resistance. Generating system shall meet the requirements of 3.4.2 and

38、3.4.3 after testing in accordance with 4.17. 3.4.12 Corrosion resistance. Generating system shall meet the requirements of 3.4.2 and 3.4.3 after testing in accordance with see 4.18. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-46795H 7 3.4

39、.13 Sand and dust. Generating system shall meet the requirements of 3.4.2 and 3.4.3 after testing in accordance with 4.19. 3.5 Finish. Unless otherwise specified (see 6.2), generating system shall be painted in accordance with the manufacturers standard practice, with outer coat of black or olive dr

40、ab enamel (see 6.3) on all exterior surfaces, except electrical connections and exposed shaft surfaces (see 4.6.2). 3.6 Identification of product. 3.6.1 Marking. Unless otherwise specified (see 6.2), generating system shall be marked in accordance with standard commercial practice (see 4.6.2). 3.6.2

41、 Nameplate. Generating system shall have a nameplate attached to alternator frame in conspicuous location so that plate may be easily read when generating system is installed in vehicle. Nameplate shall contain the following minimum information (see 4.6.2): GENERATING SYSTEM DC 60 A 28 VOLTS MAXIMUM

42、 RATED SPEED - 10 000 RPM SPECIFICATION MIL-PRF-46795 SERIAL NUMBER NATIONAL STOCK NUMBER (NSN) MANUFACTURERS NAME OR IDENTIFICATION CODE U.S. 3.7 Safety. The generating system shall be free from defects involving rotating parts, burrs or sharp edges, and electrical shock which may result in injury

43、of personnel (see 4.6.2). 4. VERIFICATION 4.1 Classification of inspections. The inspection requirements specified herein are classified as follows: a. First article inspection (see 4.3). b. Conformance inspection (see 4.4). c. Control tests (see 4.5). 4.2 Inspection conditions. Unless otherwise spe

44、cified (see 6.2), all inspections shall be conducted under the following standard (room) ambient conditions: a. Temperature: 77 + 15F (25 + 8.3C). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-46795H 8 b. Relative humidity: Uncontrolled roo

45、m ambient. c. Atmospheric pressure: Site pressure. 4.2.1 Batteries. 24 Vdc power source shall be two 12 Vdc military type batteries connected in series. A battery which accepts a charging current of not more than 4.5 A at set voltage after storage at laboratory ambient air temperature shall be consi

46、dered fully charged. In case of a high voltage reading, battery fluid specific gravity shall be inspected and, if over 1.30, battery shall be discharged until specific gravity is not more than 1.30, and charging current is not more than 4.5 A. 4.2.2 Stabilized frame temperature. Unless otherwise spe

47、cified herein, generating system frame temperature shall be stabilized prior to undergoing test procedure (see 6.4.2). 4.2.2.1 Frame temperature. Frame temperature shall be measured at center of stator lamination stack on outside diameter. 4.2.3 Test voltage. Unless otherwise specified, voltage regu

48、lator shall be adjusted to 28 Vdc + 0.2 Vdc with alternator running at 2000 rpm and producing not more than 10 A. This adjustment shall be made after frame temperature has been stabilized. 4.3 First article inspection. Samples of products to be furnished under this specification shall undergo the ex

49、aminations in 4.4.2 and tests in order listed in table I (see 3.1). TABLE I. Order of first article testing. Sample number Requirement Test Requirement 1 3.4.3 3.4.2.2 3.4.3.1 3.4.4 3.4.3 3.4.2.2 4.9.1 4.8.2 4.9.2 4.10 4.9.1 4.8.2 Rated output Voltage regulation Non-operating current Endurance Rated output Voltage regulation 2 1/ 3.4.3 3.4.2.2 3.4.6 4.9.