ARMY MIL-PRF-32367-2010 BIPOD SQUAD DESIGNATED MARKSMAN (SDM).pdf
《ARMY MIL-PRF-32367-2010 BIPOD SQUAD DESIGNATED MARKSMAN (SDM).pdf》由会员分享,可在线阅读,更多相关《ARMY MIL-PRF-32367-2010 BIPOD SQUAD DESIGNATED MARKSMAN (SDM).pdf(10页珍藏版)》请在麦多课文档分享上搜索。
1、 INCH-POUND MIL-PRF-32367 26 November 2010 SUPERSEDING PRF13018854 CAGE Code: 19200 10 October 2007 (See 6.5) PERFORMANCE SPECIFICATION BIPOD, SQUAD DESIGNATED MARKSMAN (SDM) This specification is approved for use by the U.S. Army Armaments Research, Development and Engineering Center (ARDEC) and is
2、 available for use by all Departments and Agencies of the Department of Defense. 1. SCOPE 1.1 Scope. This specification prescribes the performance requirements and identifies verification procedures for the Bipod, Squad Designated Marksman (SDM), hereafter referred to simply as the SDM Bipod. The SD
3、M Bipod provides a stable firing platform for the M4 and M16 series weapons. The SDM Bipod shall have the ability to adjust cant and leg height for leveling on uneven surface. 1.2 Requirement levels. This specification identifies two values for selected performance requirements. The threshold (T) is
4、 the minimum acceptable level. The objective (O) is the desired level at which performance results in an operationally significant increase in capabilities. When only one requirement is stated, it is the threshold requirement. 2. APPLICABLE DOCUMENTS 2.1 General. The documents listed in this section
5、 are specified in sections 3 or 4 of this specification. This section does not include documents cited in other sections of this specification or recommended for additional information or as examples. While every effort has been made to ensure the completeness of this list, document users are cautio
6、ned that they must meet all specified requirements of documents cited in sections 3 and 4 of this specification, whether or not they are listed. AMSC: N/A FSC: 1005 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. Comments, suggestions, or questions on this document
7、should be addressed to: Commander, U.S. Army ARDEC, ATTN: RDAR-QES-E, Picatinny, New Jersey 07806-5000, or emailed to ardecstdznconus.army.mil. Since contact information can change, you may want to verify the currency of this address information using the ASSIST online database at https:/assist.daps
8、.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-32367 2 2.2 Government documents. 2.2.1 Specifications, standards, and handbooks. The following specifications, standards, and handbooks form a part of this document to the extent spec
9、ified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitations or contract. DEPARTMENT OF DEFENSE SPECIFICATIONS MIL-PRF-372 Cleaning Compound, Solvent (For Bore of Small Arms and Automatic Aircraft Weapons) MIL-PRF-14107 Lubricating Oil, Weapons, Low Te
10、mperature MIL-G-21164 Grease, Molybdenum Disulfide, For Low and High Temperatures, NATO Code Number G-353 MIL-L-46000 Lubricant, Semi-Fluid (Automatic Weapons) MIL-PRF-63460 Lubricant, Cleaner, and Preservative for Weapons and Weapons Systems DEPARTMENT OF DEFENSE STANDARDS MIL-STD-810 Environmental
11、 Engineering Considerations and Laboratory Tests MIL-STD-1472 Human Engineering MIL-STD-1913 Dimensioning of Accessory Mounting Rail for Small Arms Weapons MIL-STD-1916 DoD Preferred Methods for Acceptance of Product (Copies of these documents are available online at https:/assist.daps.dla.mil or fr
12、om the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2.2 Other Government documents, drawings and publication. The following other Government documents, drawings, and publications form a part of this document to the extent specified herein. Unl
13、ess otherwise specified, the issues of these documents are those cited in the solicitation or contract. US ARMY DEVELOPMENT TEST COMMAND TOP 3-2-045 Automatic Weapons, Machineguns, Hand, and Shoulder Weapons (Copies of these documents may be ordered from the US Army Developmental Test Command, ATTN:
14、 Publications, 314 longs Corner Road, Aberdeen Proving Ground, MD, 21005-5005, or online at http:/www.dtc.army.mil/publications/topsindex.aspx). 2.3 Non-Government publication. The following documents form a part of this document to the extend specified herein. Unless otherwise indicated, the issues
15、 of these documents are those cited in the solicitation or contract. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-32367 3 ASTM INTERNATIONAL ASTM-B117 Standard Practice for Operation Salt Spray (Fog) Apparatus (ASTM standards may be ordere
16、d from the ASTM International Engineers, 100 Barr Harbor Drive, PO Box C700, West Conshohocken PA 19428-2959, or online at http:/www.astm.org/.) 2.4 Order of Precedence. Unless otherwise noted herein or in the contract, in the event of a conflict between the text of this document and the references
17、cited herein, the text of this document takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption is obtained. 3. REQUIREMENTS 3.1 Design verification. When specified (see 6.2), a sample of the SDM Bipod shall be subjected to design v
18、erification in accordance with TABLE I and 4.1. 3.2 First article inspection. When specified (see 6.2), a sample of the SDM Bipod shall be subjected to first article inspection in accordance with TABLE I and 4.2. 3.3 Conformance inspection. When specified (see 6.2), a sample of the SDM Bipod shall b
19、e subjected to conformance inspection in accordance with TABLE I and 4.3. 3.4 Operating requirements. 3.4.1 Vertical clearance. The vertical clearance shall assure a loaded 30 round magazine from touching the ground measured from the ground to the lowest possible SDM rail surface. The minimum bipod
20、vertical height is 9.5 inches for both the M4 and M16 series rifle. 3.4.2 Open and close. The SDM Bipod leg deployment and retraction shall not require the operator to move his weapon out of tactical orientation. The SDM Bipod shall also be capable of being opened and closed one-handed (see 6.4 for
21、opening and closing SMD Bipod definition). 3.4.3 Stability. The SDM Bipod shall provide a stable firing platform. The SDM Bipod with legs extended shall keep the weapon in the upright position when left unattended on a flat leveled. The SDM Bipod shall be unable to be oriented in a configuration tha
22、t shall allow the weapon to fall if left unattended. 3.4.4 Adjustment for stability. The SDM Bipod shall have the ability to adjust the cant and leg height for leveling on uneven surface and provide a stable firing platform. An uneven surface is defined as a surface 30 degrees off the horizontal pla
23、ne. 3.4.5 Aim and fire in prone position. The SDM Bipod shall enable aimed-fire shooting support from the prone position while the SDM Bipod is deployed on the ground. 3.5 Interface and interoperability requirements. Provided by IHSNot for ResaleNo reproduction or networking permitted without licens
24、e from IHS-,-,-MIL-PRF-32367 4 3.5.1 Weight. The SDM Bipod shall weigh no more than 32 ounces. 3.5.2 Non-interference. The SDM Bipod shall not interfere with the use or function of the weapon to include but not limited to blocking the ejection port, interfering with the cartridge feeding, weapon cha
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ARMYMILPRF323672010BIPODSQUADDESIGNATEDMARKSMANSDMPDF

链接地址:http://www.mydoc123.com/p-447162.html