ARMY MIL-P-60314-1965 PRIMER PERCUSSION M32 PARTS FOR《M32撞击引物的部件》.pdf

《ARMY MIL-P-60314-1965 PRIMER PERCUSSION M32 PARTS FOR《M32撞击引物的部件》.pdf》由会员分享，可在线阅读，更多相关《ARMY MIL-P-60314-1965 PRIMER PERCUSSION M32 PARTS FOR《M32撞击引物的部件》.pdf（12页珍藏版）》请在麦多课文档分享上搜索。

1、MIL-P-60314 (MU) 29 January 1965 MILITARY SPECIFICATION PRIMEFi, PERCUSSION M32 PARTS POR 1. SCOPE 1.1 This specification chers the parts for one tjrpe oc 2, APPLICABLE DWUMENTS percussion primer eesignated as R.mer, Percusslo, M32. - 2.1 The following documents of the issue In effect on date of inv

2、itation for bids or request for proposal form a part of this specification to the extent specified herein. SPECIFI$ATION MILITARY MIL-A-2550 - Amunition and Special Weapons, -General Smcificatian far. - - - - 7 Mu-P-10025 Interplant Shipnent of Inert Amunition Components, General Specif ication f or

3、r MIL-1-45208 - Inspection Requirements, Wneral Specification for. MIL-1-45607 - Inspection Equipment, Supply and Maintenance of. - Pckaging, Packing and Marking for STANDAFDS MILITARY ML-STD-105 - Sampling Procedures and Tables for Inspection by Attributes (ABC-.be In accordance with applicable dra

4、wings and apeciiications. specified on DMwings (dwgs.) 8880638, 8880639 and 8880642, as applicable, and with all requirements speeified in applicable specifications. in a thorough workmanlike manner, chips, sharp edges, cracks, unblended radii, surface defects, dirt, grease, corrosion products and o

5、ther foreign matter, The cleaning method used shall not be injurious to any part nor shall the parts be contaminated by the cleanin; agent, 3.2 Parts.-The parts shall comply with all requirements 3.3 Worlsmanshlp.-All part8 shall be fabricated and finished They shall be free of burrs, i . QUALITY AS

6、SURANCE PROKISIONS 4.1 General. quality assurance provisions.-Unless otherwise specified in the contract or purchase order, the supplier is responsible for-the performance of all inspectton requirements as 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IH

7、S-,-,-MIL-P-603L4 13 9999906 03375L15 O MIL-P-60314 (MU) specified herein. Except as otherwise specified, the supplier my utilize his own facilities or any comwrcial laboratory acceptable to the Government. The Government reserves the right to perfom any of the lnspectlons set forth in the specifica

8、tion where such Inspections are deemed necessary to assure supplies and services conform to prescribed requirements, Reference shall be made to Standard MIL-STD-109 ln order to define terms used herein. The provialone of Specification MU-A-2550 shall apply. 4.1.1 Contractor quality assurance system.

9、-The contractor shall provide and maintaln an effective quality assurance system in compliance with the requirement8 of Specification MIZ-I-45E8. The contractors quality assurance systam shall contain a procedure for the reporting of critical defective8 found during the couro$ of his inspection and

10、during Inspection by the Wvernment. Any critical defect encountered, unless annotated by an asterisk (*) to the Pight of the characteristic code number (see 6.2); will be reported within 48 hours. cr1t;lcal defects annotated by an asterisk will be furnlehe. The agencies to whom the reports will be f

11、urnished are Mentifled in paragraph 6.5. The reports shall contain, as a minmum, the tollowing inllormation: A monthly 8- report covering those a. Contractor and contract number, b. C, Characteristic code number, d. Lot or serial number. .e. Number of deTectivea found. f, g. Corrective action taken

12、or reaomnded. When the Humber and revision date of pccilcation. Assignable cause or anslysis of occurrenoe. corrective action is beyond the control of the contractor OF the scope of the contraet, the report su1 contain the contra interfix number. Lot8 shall be submitted for inspection in accordance

13、with Standard MIL-STD-105 (or Standard MIL-STD-1235, when applicable) . 5 ,.;Gage Major diameter of thread, min. , .Gage Concentricity of firing plug hole with rcspectto firing plug cavIty,.Ge Concentrlcity of firing plug cavity with pitchadlameter of teads.O.e,Gage Concentricity of housing cavity w

14、ith respect to firing plug cavity,.Ge Concentricity of housing cavity with respect to pitch diameter of tklIleads,.Gage Diameter of firing plug cavityGage Diameter of firing plug holeGage Depth from face of crimping wall to bottom of firing plug cavtyl.6.oGe Total lengthO.Gage 6 /-y, Code No. (see 6

15、.2) O1001 01002 01003 01004 01005 01006 01007 01008 O1009 O1010 - J Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-P-bO31g 13 77970b 03375g7 4 Minor: 201 202 203 . 204 . 205 . 206 . 207 . 208 . 209 . .210 211. MIL-P-60314 (MU) AQL 4.00 percent D

16、iameter of crimp wall.Gage Height of crimp wall;Gage Diameter of housing cavity.Gage Length of thread undercut, -.Gage Diameter of flange.Gage Concentricity of wrench holes with respect to the firing plug hole.OO.*.Ge Pitch diameter of thread, maxGage Major diameter of thread, max. .Gase Evidence of

17、 poor workmanship . Thcbess of flangeGage (see 3.3) . .visual Flniah improper. . Vlsual O1011 O1012 01013 01014 01015 01016 01017 01018 O1019 01020 01021 4.3.2.2 Housing (see dwg. 8880639) e Categories Defects Method of Inspection Code No. Critical: 1, .Flash hole mlssing or ObstlCUcted*Vlsual 02001

18、 * 2. Crack or split . Visl 02002 * Major : AQL 1.00 percent 101. Diameter of pellet cavity.,Gage 02003 102, Depth of pellet cavity.,-a.Gage 02004 103. Diameter of primer cavity.;Gage 02005 104. Depth of primer cavity,Gage 02906 105, Diameter of countersink, max. Qage 02007 106, Location and profile

19、 of crimp- ing a1e0.G8ge 02008 Minors ACe 104, Height of point,.,Gage 105. Length from Bhoulder to point.Gage 106, Total leth,Ge 107. Concentricity of small outside diameter to large outside diameter,.,.Oase 108. Finish improper.,Visual 109. Point damed,.,.,Visual Minor : AQL 1.00 percent 201. Radiu

20、s impropf3r,e 202. Evidence of poor workqanshlp (see 3.3) ,isua Code No. 03001 03002 03003 03004 03005 03006 03007 03008 03009 03010 03011 4.3.3 Inspection Equipment.-Index of Inspection Equ-pment Number IEL-6112755 identifies the insljection equipment required to perform the examinations and tests

21、prescribed in this section. The contractor shall design inspection equipment in accordance with the instructions in paragraph 6.3. equipment drawings and lists provided and revised in accordance with the requirements OP the for design, procurement, manufacture, testin;, evaluation, production and re

22、ceiving inspection, overhaul, shipping, storage, identification of stock, ordering and storage of replacement parts, inspection of items at overhaul, general maintenance of equipment, construction, survey and whenever Inspection equipment drawings are needed. 4.3.3.1 Government rights to documentati

23、on,-Inspection may be used by DOD activities 4.3.3.2 Supply and maintenance.-Supply and maintenance of the equipment listed on the IEL shall be in accordance with Specification ML-1-45607. 8 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-Mn-P-60314

24、(MU) 4.3.3.3 Government us8 of contractorls inspection and test equipment.-The contractor shall make available to the Government all inspection and test equipment necessary for determining con- fomnance with contract, requirements. equipnent, and veriflaation of its accuracy, shall be supplied by th

25、e contractor for the performance of examination or test by the overnment . Personnel for operating the 50 PMPARATIOM FOR IELIVERY 5.1 Packing and marking 5.1.1 Level C.-The parts shall be packed and marked in 5.2 Data cards.-Data cards shall be prepared for each lot accordance with Speciflcation ka-

26、P-10025. in accordance with the information specified in Specification MIL-A-2550. 6. NOTES 6.1 Ordering data.-Procurement documents shall specify title, number and date of this specification, 6.2 Inspection code numbers,-The five digt code numbers assigned to the inspections herein are to facilitat

27、e future data collection and analyeis by the Government. 6.3 Inspection equipmenC.-The contractor shall design inspection nt as required by the referenced Inspection Equipnent Lists in accordance with the instructions of paragraphs 6.3.1 bhrough 6.5.7. 6.3.1 Inspection equipaent lists,-Inspection eq

28、uipment lists indicate the availability of inspection equipment designs by showing in the mnumbez.-u column of the list of inspection equipment (O0 Form 1242-3) the numbers of drawings of existing equipment designs or cades as indicated in paragraph 6.3.2. contractor with respect to the different ty

29、pes of drawings that may be liatsd is desoribed in paragroaphs 6.3.3 and 6.3.4. by the contractor with respect to commercial Inspection equipment la described in 6.3.5. Design action required of the Action required The contractor will be required to prepare 9 Provided by IHSNot for ResaleNo reproduc

30、tion or networking permitted without license from IHS-,-,- flIL-P-bO3Lq 13 W 9999906 0337552 B W _ - - - MIL-P-60314 (pIII) detailed drawings in accordance with 6.3.6 for all the equipment coded as “Contractor Design“ In the number column. These contractor designs must be approved by %he Government

31、prior to fabrication OP procuring of the equipment. h3ignS shall be submitted for approval as specified in 6.3.7. 6.3.2 Inspection equipment list codes.-The inspection equipment as defined in 6.3.3, 6.3.4, 6.3.5 and 6.3.6 will be designated in the IEL by the following codes: . CDAF - Contractors des

32、ign responsibility on Army format In CDCF - Contractors design responsibility on contractor AD - Army design. ADMT - Army design, mandatory for u8e. CE - Commercial equlpnt. SCD - Specification control drawing. accordance with MIL-D-45608. format. 6.3.9 Army designs.-Amy designs are reflected on det

33、ailed drawinas which completely depict all the Information necessary for the fabrication of the item of inspection equipment. need provide no design when an Army design is listed for an item af inbpection equipment, Army designs fall into two basic classifications, mandatory and non-mandatory. When

34、an inspection equipment list references mandatory Army designs, the contractor shall comply with, and use these designs accordingly. The contraetor may, however, in connection with non-mandatory designs and with the approval of the Government, esign alternate Inspection equipment or use comparable c

35、ommercial equipment to facilitate hi8 operations. Such contractor prepared designs or commercial equip- ment selections must be approved by the Government prior to fabrication or procurin; of the equipment. mitted forapproval as specified in 6.3.7. drawings depict the minimum equipment requirements

36、in outline, deBCripkive, diagramatic or pictorial form only and specify the requfred performance or other characteristics, prepare detailed drawings (see 6.3.6) of their designs in support of specificat.on control drawings. The contractor Designs shall be sub- 6. 3.4 Specif cation control drawing. -

37、Specif icatlon cntrol Contractors must These contractor prepared 10 /- - Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-P-60314 (MU) designs muat be approved by tho Qove=nt prior to the faBrlcatlon or procuring of he equlgment. rsquromontr of sp

38、sairioation coQtrol rawngr may be approvod If described In sufficient detabl bo priait Identifloation and evaluat.lon by the C#uvernmont. approval a8 spoclfleld In 6.5.7, Cbmwrolal oqulpaient metin$ tho DO8i(inS shall bo suknitted for 6,%5 CoaiMrcal equbpmro tho oxtont that -thor calculation or olar

39、lficmtion ni31 not be rmlrrd, Uontraotor designa identflod a# CDW ray ?m dewlopod on tho formt tho oontraotor nozdily amployr.ln Ur -1-t eslgn pmeeuro provlod ruoh format roflootr tho dotai1 and IxuPoma6fon spooi$l.d abovo. Contraator oilgni dentiflod u W 8haJ.l o- with the forerb u1c1 zhqulmmantr o

40、f MIEp45608, TM tn addition8 oontaln the d8Wl and Information rpoolflod abovi. Contractor deiligns ahall be OQU%mltL Th18 POQUgrO8 that Ohe nOaOr.i1Y)r VlOW8, mN30ni8 6.4 Sul Submission of critical defect reporta.-For U, S, Army Munitions Command procurements, one copy of each critical defect report

41、 will be furnished the cognizant Government inspection agency; the Army Ammunition Procurement and Supply Agency, ATTN: SWAP-RO; Picatinny Arsenal, ATTN: SMUPA-ND, 6.5.2 Reporthg to other services,-For other than U. S. Army Munitions Command procurements, critical defect reporting shall be as pirescribed by the contracting officer, Custodian: Amy-M ProJect No. 1375-A832 12 Preparing activityt Army-Mu Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-