ARMY MIL-P-48663-1986 PALLET METAL FOR METAL CONTAINER FOR 105MM AND 120MM TANK AMMUNITION《105 mm和120 MM坦克弹药用金属容器用金属托盘》.pdf

《ARMY MIL-P-48663-1986 PALLET METAL FOR METAL CONTAINER FOR 105MM AND 120MM TANK AMMUNITION《105 mm和120 MM坦克弹药用金属容器用金属托盘》.pdf》由会员分享，可在线阅读，更多相关《ARMY MIL-P-48663-1986 PALLET METAL FOR METAL CONTAINER FOR 105MM AND 120MM TANK AMMUNITION《105 mm和120 MM坦克弹药用金属容器用金属托盘》.pdf（10页珍藏版）》请在麦多课文档分享上搜索。

1、- MIL-P-4bb3 AL 7777906 028bb3 O W5-39-05- MIL-P-48663 (AR) 8 September 1986 MILITARY SPECIFICATION PALLET, METAL, FOR METAL CONTAINER FOR 105MM AND 120MM TANK AMMUNITION This Specification is approved for use within the U.S. Army Armament, Munitions and Chemical Command, and is available for use by

2、 all Departments and Agencies of the Department of Defense. 1. SCOPE 1.1 Scope. This specification covers the fabrication of a number of the selected items, quality assurance provisions and packaging of the special metal pallets for tank ammunition pallets. The special pallets will consist of a base

3、 and a cover that will unitize the selected quantity and type of the metal container for the 105MM and 120MM tank ammunition cartridge. 2. APPLICABLE DOCUMENTS 2.1 Government documents. 2.1.1 Specification and standards. The following soecifications and standards form a part of this specification to

4、 the extent specified herein. issues of these documents shall be those listed in the issue of the Department of Defense Index of Specifications and Standards (DODISS) and supplement thereto, cited in the solicitation. Unless-otherwise specified, the SPECIFICATIONS FEDERAL TT-C-4 90 - Cleaning and Pr

5、eparation of Ferrous and Coated Surfaces for Organic Protective Coatings Beneficial comments (recommendations, additions, deletions) and any pertinent data which may be of use in improv- ing this document should be addressed to: Commander, US. Army Armament Research, Development and Engineer- ing Ce

6、nter, Attn: AMSMC-QA, Dover, New Jersey 07801-5001 by using the self-addressed Standardization Document Improvement Proposal (DD Form 1426) appearing at the end of this document or by letter. F -. THIS DOCUMENT CONTAINS /o PAGES. AMSC N/A FSC 8140 DISTRIBUTION STATEMENT A. Approved for public releas

7、e; distribution is unlimited. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-P-48663 (AR) MILITARY MIL-W-12332 MIL-A-48078 STANBARDS MILITARY MIL-STD-105 MIL-STD-971 MIL-STD-1261 II Welding Resistance, Spot, Seam and Production, for fabricating

8、Assemblies of Low-Carbon Steel CI Ammunition, Standard Quality Assurance Provisions, General Specification for L Sampling Procedures and Tables for “ Finishing of Metal and Wood Surfaces II Welding Procedures for Constructional Inspection by Attxibutes Steel 2.1.2 Other Government documents, drawing

9、s, and publications. The allowing othel: Government documents, drawings, and publica- tions Eorm a part of this specification to the extent specified herein. Unless othexwise specified, the issues shall be those in effect on the date of the solicitation. US Army Defense Ammunition Center and School

10、AC 2 O O O O 3 53 - Pallet, Metal, for Metal Containers (Copies o speciEications, standards and other Government documents required by manufacturers in connection with specific acgufsition functions should be obtained from the contracting activity 01: as directed by the contracting activity). o this

11、 specification to the extent specified herein. Unless othecwise apeciied, the issues of the documents which are DoD adoptad shall be those listed in the issue of the DoDISS specified in the solicitation. Unless otherwise specified, the issues o documents not Zisted in the DoDISS shall be the issue o

12、f the non- government documents which is current on the date of the solicitation. 2,2 Other.publication+ The following documents form a part e 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- flIL-P-4b63 81 9779906 28bOb5 4 MIL-P-48663 (AR) AMERICA

13、N SOCIETY FOR TESTING AND MATERIALS (ASTM) ASTM-E8 - Tension Testing of Metallic ASTM-D3 951 - Standard Practice for Commercial Materials, Standard Method o Packaging (Application for copies should be addressed to the American Society for Testing and Materials, 1916 Race Street, Philadelphia, Pennsy

14、lvania 19103) 2.3 Order of precedence. In the event of a conflict between the text of this specification and the references cited herein, (except for associated detail specifications, specification sheets or MS standards), the text of this specification shall take precedence. However, shall supersed

15、e applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Materials. Materials and parts shall be in accordance with applicable drawings and specifications. 3.2 Pallets. The pallet assemblies shall comply with all requirements specified on drawing (dwg) AC2

16、0000353 and associated drawings and with all requirements specified in applicable specifications and standards. 3.3 Stackinq load. The pallets shall be able to withstand a 10,000 pound stacking load. 3.4 Weldinq. The welding shall comply with the requirements 3.4.1 Tensile strenqth. The tensile stre

17、ngth of the weld of MIL-W-12332 or MIL-STD-1261. shall equal or exceed the tensile strength of the material. 3.5 Painted surface. The painted surfaces of the pallets shall comply with the requirements of W-C-490. 3.6 First article inspection. This specification contains technical provisions for firs

18、t article inspection. Requirements for the submission of first article samples by the contractor shall be as specified in the contract. 3.7 Workmanship 3.7.1 Pallets. The pallets shall be regular, smooth, and free from wrinkles, cracks, rough spots, burrs, sharp edges and any other defect that might

19、 affect the serviceability, durability, safety and appearance of the pallets. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-P-48663 (AR) 3,7.2 Paint coating, The paint coating shall be in accordance with applicable drawings and comply with inst

20、ructions in MEL-STD-171. The Einish coat shall cover all required surfaces and be continuous with the possible exception o a ew light scratchee not exposing the base metal or the primer coat. 3.7.3 Parts. All parts shall be free of chips, dirt, grease, rust and foreign material, injurious to any of

21、the parts nor shall any of the parts be contaminated by the cleaning agents used, The cleaning method used shall not be 4. QUALITY ASSURANCE PROVISIONS 4.1 Responsibility for inspection . Unless otherwise saecieied in the contiaet or purchase order, the contractor is raaysnsible or the performance o

22、f all inspection requirements as specified herein. Except: as otherwise specified in the contract or purchase order, the contractor may use his own or any other facilities suitable for the performance of the inspection requirements specified herein, unless disapproved by the Government. The Governme

23、nt: reserves the right to perform any of the inspections set orth in the specification where such inspections are deemed necessary to assure supplies and services csnform to prescribed requirements, herein ox: in the contcact, the provisions o MIL-A-48078 shall apply and are hereby made a part of th

24、is detail speciication. Unless otherwise specified 4.101 Responsibiiity or compliance, All items must meet all requirements o sections 3 and 5. this spciication shall become a part of the contractorss ovecall inspection system or quality program. inspctfon requirements in this specification shall no

25、t celieve the contractor of the responsibility o assuring that all products or supylios submitted to the Government for acceptance comply with all requirements o the contract, Sampling in quality conformance does not authorize submission of known defective material, either indicated or actual, nor d

26、oes it commit the Government to acceptance of deective material, The inspection set forth in The absence of any 4,2 Classiication of inspections, The following types o inspections shall be conducted on this item: a. First Article Inspection ts. Quality Conformance Inspection, 4.3 First article inspe

27、ction, 4.3.1 Submission. The contractor shall submit a first article sample as designated by the Contracting Officer for evaluation in accordance with provisions of 4.3,2 The first article sample shall consist of dash numbered assemblies as per itwg AC20000353 listed in Table I, of this specificatio

28、n. 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-P-48663 81 m 777770b 028bOb7 8 m MIL-P-48663 (AR) 0 TABLE I. First article quantities DRAWING PALLET QUANTITIES METAL CONTAINER DASH NO. CONFIGURATION REQUIRED NOMENCLATURE OF METAL OF-FIRST CO

29、NTAINERS ARTICLE -1 6 Wide by 5 High 8 105MM Light Weight Container -2 6 Wide by 5 High 8 105MM PA 104 Container -3 5 Wide by 6 High 6 120MM Light Weight Conta iner 4.3.2 Inspections to be performed. See MIL-A-48078 and Table II specif i.ed herein. 4.3.3 Rejection. See MIL-A-48078. 5 Provided by IHS

30、Not for ResaleNo reproduction or networking permitted without license from IHS-,-,-I C Ii d u u a f I. l. f E F I U al ri ri m pi 4 m U d cf QI Q, n n M- oo I- m O i- E L o IL n a v a QI cz n h L 6 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-L MI

31、L-P-48663 1 W 7777906 02860b7 L I I MIL-P-48663 (AR) 4.4 Quality conformance inspection. 4.4.1 Inspection lot formation. Inspection lots shall comply with the lot formation provisions of MIL-A-48078. 4.4.2 Examination. See MIL-A-48078. Unless otherwise specified in the Classification of Defects and

32、Test Tables, sampling plans and procedures for major and minor defects shall be in accordance with MIL-STD-105, Inspection Level II. 100% inspection may be performed at the discretion of the Contracting Officer s Representative (COR) . 7 Provided by IHSNot for ResaleNo reproduction or networking per

33、mitted without license from IHS-,-,-n A m Y 8 om 4 U a Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-, MIL-P-48663 81 7779706 0286071 T d MIL-P-48663 (AR) i I l a L i 4.4.3 Testing. 4.4.3.1 Inspection equipment. The inspection equipment required to

34、 perform the examinations and tests prescribed herein is described in the “Paragraph Reference/Inspection Method“ column in the tables starting with paragraph 4.4.3.1. The contractor shall submit for approval, inspection equipment designs in accordance with the terms of the contract. See Section 6 o

35、f MIL-A-48078 and 6.4 herein. 4.5 Methods of inspection. 4.5.1 Tensile strength. The tensile strength shall be determined in accordance with ASTM-E8. Three specimens of each gage thickness shall be selected from the material used to fabricate the pallets for determination of the material tensile str

36、ength. Also, the tensile strength of the welds will be determined by applying the force at right angles to the weld. Each of these values shall be compared with the lowest determined value of the body material tensile strength for compliance with the requirement of 3.4.1. If the samples cannot meet

37、these requirements the lot will be rejected. 4.5.2 Stacking strength. The number of samples, as listed in Table I of the specification, shall be randomly selected for this test. The pallet shall be loaded, to simulate a stack of identical pallet loads, to the stacking load requirement for a period o

38、f 1 hour minimum. If any pallet fails to meet the requirement, the lot shall be rejected. 5. PACKAGING 5.1 Preservation and packaginq. None required. 5.2 Packing. 5.2.1 Commercial. The metal pallet shall be packed in accordance with ASTM-D-3951. 5.3 Marking. 5.3.1 Commercial. Shipping marking shall

39、comply with ASTM D3951-82 and the following additional instructions. No shipping marking shall be placed directly on the pallets. Commercial shipping tags attached with wire shall be used unless otherwise specified. The following information shall be shown: Item name and model number, part number an

40、d revision, contract number, and date, name and address of manufacturer. If pallets are bundled, boxed or bulk-contained, the gross weight and quantity shall be included. The above information may be placed on bulk-containers or boxes b_y labeling or stenciling. Provided by IHSNot for ResaleNo repro

41、duction or networking permitted without license from IHS-,-,-MIL-F-48663 (AB) 5.4 Shi in When pallets from more than one lot are shipped at -=-? one t me, each lot shall be kept separate and the division between lots clearly indicated to prevent mixing lots in tlxmsit. 6. NOTES 6.1 Intended use. Thi

42、s metal pallet is intended for use with the metal. tank ammunition container for the 105MM and 120MM tank ammunition cartridge, 6.2 Ordering data, See MIL-A-48078 6,3 Submission of inspection equipment for design approvals. Bee MIL-A-48078. Submit designs as required to: Commander, US Army Armament

43、Research, Development and Engineering Center, ATTN: AMSMC-QAT-I(D), Dover, New Jersey, 07801-5001. 6,4 Approval of equivalent test methods, Prior approval of the Contracting Offioer- is required for use of equivalent test methods. A description of the proposed method should be submitted through the

44、Contracting Oficer to: Commander, US Army Armament Research, Development and Engineering Center, ATTN: AMSMC-QAP-A(D) Dover, New Jersey 07803-5001. This description should include but not be Limited to the accuracy and precision and drawings of any special equipment required. 6.5 Subject term (key word) listing. Amuni tion Cannon Cartridge Container Metal PalLet Tank eus todi an: Army-AR Preparing activity: (Project 8140-A718) Army-AR Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-