ARMY MIL-P-48663 (2)-1994 PALLET METAL FOR METAL CONTAINER FOR 105MM AND 120MM TANK AMMUNITION《105 mm和120 MM坦克弹药用金属容器用金属托盘》.pdf

《ARMY MIL-P-48663 (2)-1994 PALLET METAL FOR METAL CONTAINER FOR 105MM AND 120MM TANK AMMUNITION《105 mm和120 MM坦克弹药用金属容器用金属托盘》.pdf》由会员分享，可在线阅读，更多相关《ARMY MIL-P-48663 (2)-1994 PALLET METAL FOR METAL CONTAINER FOR 105MM AND 120MM TANK AMMUNITION《105 mm和120 MM坦克弹药用金属容器用金属托盘》.pdf（4页珍藏版）》请在麦多课文档分享上搜索。

1、IINCH-POUND I MIL-P-48663 (AR) AMENDMENT 2 76 August 1994 SUPERSEDING AMENDMENT 1 11 June 1990 MILITARY SPECIFICATION PALLET, METAL, FOR METAL CONTAINER FOR 105MM AND 120MM TANK AMMUNITION This amendment forms a part of Military Specification MIL-P-48663 (AR), dated 8 September 1986, and is approved

2、 for use by the U.S. Army Armament, Munitions and Chemical Command and is available for use by all Departments and Agencies of the Department of Defense. PAGE 4 3.7.3: Delete the first sentence and substitute the following: IA11 parts shall be free of chips, dirt, grease, rust except in areas inacce

3、ssible to paint, and foreign material. Weld splatter shall be permissible on non-load bearing surfaces provided that it is firmly attached.“ PAGE 8 4.4.2.1 Metal Pallet, under Notes, add: “(a) with each lot of material submitted. (b) Three specimens of each gage thickness.ii PAGE 10 * Add the follow

4、ing APPENDIX as pages 11 and 12, included herein. AMSC N/A 1 of 4 FSC 8140 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- NIL-P-4bb3 (2) W 9Ob 1987422 489 W MIL-P-486

5、63 (AR) AMENDMENT 2 “APPENDIX QUALITY ASSURANCE PROVISIONS FOR REFURBISHMENT 10. SCOPE: 10.1 Scope. This appendix provides the Quality Assurance provisions for the refurbishment of metal pallets and adapters. 20. APPLICABLE DOCUMENTS: STANDARDS MI LI TARY MIL-STD-105 Sampling Procedures and Tables f

6、or Inspection by Attributes. MIL-STD-171 Finishing of Metal and Wood Surfaces. 30. REFURBISHMENT: 30.1 Cleaninq. Loose paint, dirt, grease and rust shall be removed. 30.2 Refinish. The parts shall be finished in accordance with the applicable drawings with the following exception: a. For refinishing

7、 of adapters, “Finish 20.1 or 20.2“ from MIL-STD-171 may be utilized. 40. REOUIREMENTS: 40.1 Welds. Welds shall be in accordance with good commercial practices. 40.2 Stackabilitv. The top lift adapter and pallet shall not be deformed to the extent that it effects safely stacking of pallets in storag

8、e. 40.3 Lifting rinqs. deformed to the extent of preventing safe handling by a sling during top lifting operations. The lifting rings shall not be damaged or Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-P-4bb3 (2) = 999990b 1987423 315 = MIL-P

9、-48663 (AR) AMENDMENT 2 40.4 Adapters. The top lift shall not be deformed to the extent that it does not engage the containers. 40.5 Workmanship. See paragraph 3.7 unless otherwise specified below: a. Deformation or damage that does not effect stacking, slinging or assembly of the pallet is allowed.

10、 b. Damage or deformation to the pallet legs that does not allow four way entry or prevents the pallet from resting evenly on a level surface is not allowed. 50. INSPECTION: 50.1 Examination. Unless otherwise specified examinations for major and minor characteristics shall be performed in accordance

11、 with MIL-STD-105, inspection Level II. 50.1.1 Metal Pallet and Adapter (see drawinqs listed in 2.1.2 as applicable). AQL INSPECTION CLASS CHARACTERISTICS or 100% METHOD Critical None defined Mai or 101 Welds missing or broken i. 0% 40. i/Visual 102 Stacking surface deformed 1.0% 40.2/Visual 103 Lif

12、ting rings damaged or deformed 1.0% 40.3/visual 104 Adapter damaged or deformed 1.0% 40.4/Visual Minor 201 Marking, missing, incorrect or illegible 1.0% 3.2/Visual 202 Protective finish damaged 1.0% 3.2/Visual 203 Poor workmanship 1.0% 40.5/Visual“ Provided by IHSNot for ResaleNo reproduction or net

13、working permitted without license from IHS-,-,- MIL-P-48bb3 (2) 9799906 l178Y2Y 251 MIL-P-48663 (AR) AMENDMENT 2 The margins of this amendment are marked with an asterisk or vertical lines to indicate where changes (additions, modifications, corrections, deletions) from the previous amendment were m

14、ade. This was done as a convenience only and the Government assumes no liability whatsoever for any inaccuracies in these notations. Bidders and contractors are cautioned to evaluate the requirements of this document based on the entire content irrespective of the marginal notations and relationship to the last previous amendment. Cus tod ian : Army-AR Preparing activity: Army-AR (Project 8140-0012) 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-