ARMY MIL-O-71152-1993 OBTURATING RING PLASTIC SPLIT (MOLDED)《分裂式塑料(模塑)密封圈》.pdf

《ARMY MIL-O-71152-1993 OBTURATING RING PLASTIC SPLIT (MOLDED)《分裂式塑料(模塑)密封圈》.pdf》由会员分享，可在线阅读，更多相关《ARMY MIL-O-71152-1993 OBTURATING RING PLASTIC SPLIT (MOLDED)《分裂式塑料(模塑)密封圈》.pdf（15页珍藏版）》请在麦多课文档分享上搜索。

1、 . a; - I INCH-POUND 1 M IL- 0- 7 1 i. 5 2 (AR) O1 November 1993 MILITARY SPECIFICATION OBTURATING BAND, PLASTIC SPLIT (MOLDED) This Specificat-ion is approved for use by the U.S. Army Armament, Munitions and Chemical Command, and is available for use by all Departments and Agencies of the Departmen

2、t of Defense. I. SCOPE 1.1 - Scope. This specification provides requirements and quality assurance provisions for obturating band, Plast-ic, split (molded) for use on the Cartridge, 60mm, Short Range, Practice, M766. 2. APPLJCABLR DOCUMENTS 2.1 Government documents. - -_-_-.- 2.1.3 Specifications, s

3、tandards and handbooks. The following specifications, standardsand handbooks form a part of this document to the extent. specified herein. Unless otherwise specified, the issues of these documents shall be those listed in the issue of the Department of Defense Index of Specifications and Standards (

4、DODISS) and supplement thereto, cited in the soljcitation (see 6.2). SPEC IF ICAT IONS M I L I T ARY MIL-A-48078 - Ammunition Standard Quality Assurance Provisions, General Specification for Beneficial comments (recommendations, additions, deletions) and any perhent data which may be of use in impro

5、ving this document, should be addressed to: Commander, U.S. Amy ARDEC, A“: SMCAR-B AC-S, Picatinny Arsenal, NJ 07806-5000 by using the Standardization Document Improvement Proposal (DD Form 1426) appearing at the end of this document or by letter. AMSC NIA FSC 1395 Approved for public release; distr

6、ibution is unlimited. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-0-71152 (AR) STANDARDS M ILTAHY MIL-STD-1 O9 - Qual i t.y Assurance Term arid Def i nit.i ons MIL-STD-1169 - Packaging, Packing and Marking for Shi pmerit. of Inert- Ammuni t.i

7、 on Components (Unless otherwise indicated, copies of federal and military specifications, standards, and handbooks are available from the DODSSP - Cust-omer Service, Standardi zation Documents Order Desk, 700 Robbins Avenue, Bldg. 4D, Philadelphia, PA 19111-5094.) 2.1.2 -_ Ot-her Government documen

8、ts, drawings, and publications. -I The following other Government documents, drawings, and publications form a part. of this document. to the extent. specified herein. Unless ot-herwise specified, the issues shall be those in effect on t.he date of the solicit.at-ion. DRAWINGS U.S. ARMY ARMAMENT RES

9、EARCH, DEVELOPMENT AND ENGINEERING CENTER (ARDEC) 12953573 - Ring, Obturating (Copies of drawings, and publicat ions and other Government documents required by contractors in connection wi t-h specific acquisition funct ions should be obtained from the contracting activity or as directed by the cont

10、racting officer.) 2.2 Non-Government publications. The following document(s) -_-_I form a part of this document t-o the extent. specified herein. Unless ot.herwise specified, the i ssues of the documents which are DoD adopted are those listed in t.he issue of the DODISS tit-ed in t.he solicitat-ion.

11、 Unless otherwise specified, the issues of documents not listed in the DODISS are the issues of the document-s cited in the colicitat-ion (see 6.2). AMERICAN SOCIETY OF TESTING AND MA?I?EHIAL (ASTM) ASTM-D2 5 6 - Tests for Impact Resistance of Plastics ASTM-D63 8 - Test for Tensile Properties of Pla

12、stics ASTM-D648 - Test for Deflection Temperature of ASTM-D79 O - Tests for Flexural Properties of Plastics and Electrical Tnsulat ing Materials Plast-ics Under Flexural Load and Electrical Insulating Materials 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license fr

13、om IHS-,-,-MIL-0-71152 9999906 L9692LL BLT MIL-0-71152 (AR) (Application for copies of ASTM publications should be addressed to the American Society for Testing and Materials, 193.6 Race Street, Philadelphia, PA 19103) . 2.3 Order of precedence. In the event of a conflict between the text of this do

14、cument and the references cited herein, the text of this document takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. (See contract provisions for additional precedence criteria). 3 . REQUIREMENTS 3-1 Material

15、. Materials shall be in accordance with applicable drawings, specifi.cations, and this specification. 3.3 .I Cert-if icati.on. Certification must be furnished by the molder for each lot of bands certifying that the plastic used in molding complies with the requirements of 3.1. 3.2 Molded parts. Obtu

16、rators shall comply with the applicable requirements specified on drawing 1 2953573 and shall be produced by the injection molding process. 3.3 Translucency. Molded parts shall be sufficiently translucent to inspect for voids. 3.4 Physical property of molded parts. Material used to produce obturator

17、s shall meet the properties listed as follows: Character is tic Requirements Izod impact strength (min) 3 O0 Joules/meter (J/M) Tensile yield strength (min) I O0 Megapascal (MPa) Flexural Modulus (min) 4500 Megapascal (MPa) Deflection temperature under a load at 1820 kilopascal (KPa) 345 degrees cen

18、tigrade 3.5 Proving ground test. The mean muzzle velocity of the test rounds (Group 1, with test obturators) shall not differ more than 5 feet/sec frm t-hat of the comparison rounds (Group 2, with accepted obturators) when tested in accordance with 4.4.3.2. The variances of the Group 1 , S1 and Grou

19、p 2, S1 , shall be as follows (see 4.4.5.2.2): SI. O K x lu- E c U S 7 3 E O LL 6 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-0-71152 9 9999906 1969215 465 9 MIL-0-71152 (AR) 4.4 Quality conformat-ion insi3ect.ion. 4.4.3 Inspection lot. forma

20、tion. Inspection lots shall comply with the lot. formation provisions of MIL-A-48078 and t-he following as applicable. 4.4.3.1 Obturator lot A lot. shall consist of obturators produced by one manufacturer in one unchanged process, in accordance with %he same drawing, same drawing revisions, same spe

21、cification and same cpecificati.on revision. Each inspect-ion lot. shall contain: bands manufact-ured from one lot- of resin and molded in one mold on one machine. 4.4.2 Examinati on and t-est-s. a. Classification of characteristics. Qua1it.y conformance examinationsand t-ests are specifiedin the fo

22、llowing Classificat-ion of Characteristics paragraphs. The contract-ors quality program or detailed inspect-ion system shall provide assurance of compliance of all characteristics with the applicable drawing and specification requirements utilizing as a minimum the conformance criteria specified her

23、ein. When cited herein, attributes sampling inspection shall be conducted in accordance wit) TABLE I below, using the inspection levels cited in the Classification of Charact-erist ics paraqraphs. 7 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL

24、-0-71 152 (AR) TABLE II. At.tributes samrslina insDect.ion . LOT SIZE 2 to 8 9 to 15 16 to 25 26 to 50 51 to 90 91 to 350 i53 to 280 281 to 500 501 to 1200 1201 to 3200 3201 to 10000 10001 to 35000 35001 to 1.50000 150001 to 500000 500000 and over * * * * * * * * * 1 250 1250 1 250 1250 1250 1250 1N

25、SPE:CTION LEVELS II I * * * * * 125 125 125 125 125 1 25 31 5 33 5 500 500 III - * * * 32 32 32 32 32 80 80 125 125 1 25 200 200 IV - * 33 13 33 13 13 32 32 50 50 50 80 80 I25 125 V - 5 5 5 5 33 13 20 20 20 32 32 50 50 50 50 VI - 3 3 3 3 5 5 8 8 13 13 13 33 13 13 13 a -.- -_.-_c- - Numbers under ins

26、pection levels indicate sample size; ast-er isks indicate one hundred percent inspect ion. If sample size exceeds size, perform one hundred percent inspection. Accept. on zero and reject on one or more for all inspect.ion levels. - - -.-.-c- - - - - - - b. Alternative quality conformance I. provisio

27、ns. .- - - - Unless otherwise speci-fied herein or provided for in the contract., alternat-i.ve quality conformance procedures, methods or equipment., such as statistical process control, tool cant-rol, variable sampli-ng or other types of sampli.nq procedures etc. may be used by the contractor when

28、 they provi.de, as a minimum, the level of quality assurance required by the provisions specified herein. Prior to applying such alternative procedures, methods or equipment, the contractor shall describe theni in a writ.t.eri proposal submitted to the Government for evaluation (See 6.6). When requi

29、red, the contract-or shall demonstrate that. the effect-iveriess of each proposed alternati.ve(s) is equal to or better than the specified quality conformance provi.sions herein. In cases of dispute as to whether the contractors proposed alternative (s) provides equivalent: assurance, the provisions

30、 of this specif icat.ion shall apply. All approved alternati.ve provi sions shall be specifically incorporated into the contractors quality program plan or inspection system, as applicable. 8 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-0-71LC

31、2 m Ob Lb2L7 238 m -Cl- amam Inmm m YI- - m Y a a, c *d ici a, a a, C O z a m tTi om ici O. .ri c di LI E Ga mciici ow a, 9 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-0-71152 = 0b 1b218 174 t- cn W group 1 of 25 rounds conditioned for 24 hou

32、rs at +70 degrees F - + 2.5 degrees F, group 2 of 25 rounds with the standard obturator 12 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-0-7LL52 9979906 Lb9221 769 m MIL-0-71.1 52 (AR) shall be conditioned at +70 degrees F + 2.5 degrees F, grou

33、p 3 of 5 rounds conditioned at +145 degrees F +-2.5 degrees F, group 4 of 5 rounds conditioned for 24 hours at. -50 degrees F + 2.5 degrees F, group 5 of 5 rounds conditioned at +145 degrees F-+ 2.5 degrees F and group 6 of 5 rounds conditioned at -50 degrees-F + 2.5 degrees F. The individual veloci

34、ties shall be recorded on the firing record. The arithmetic averages shall be calculated and recorded. Temperature of t.he day, weather and the tirne of firing shall be recorded. Smear camera shall be used to photograph all samples, The camera shall be posit-ioned to provide phot-o coverage of the t

35、est. rounds at 20 feet from the muzzle of the mortar tube. 4.4.5.2.1 -I- Test- validity. If for any reason the Government considers that. t.he test conditions have dei-rimentally affected the test results, the test. resu1t.s shall be declared invalid and a new test. shall be performed on additional

36、sample cartridges. 4.4.5.2.2 Statistical test Calculat-e S1 for test- group 3 and S2 for comparison group 2 (see Table III). Where S1 = Standard deviat-ion of t.he muzz1.e velocity of t-he twenty-f i.ve t-est. samples. S2 = Standard deviation of the muzzle ve1ocit.y of t-he twenty-five comparison sa

37、mples. - X1 = Average of the muzzle velocities of the t-wenty-five test. samples. - X2 = Average of the muzzle velocit.ies of th! t.went.y-five comparison samples. s2 If S12 Sz2 , Calculate - 1 = K (see Not-e 1 and 2) L Note 1: If K 2.27, the test. shall be rejected. Note 3: If S12 S22 and y, is wit

38、hin - +5 ft./sec of 22 , the test. lot. shall be accept-ed. 5. PACKAGING 5.1 Packaging, packing, - and marka. Packaging, packing, and marking shall be in accordance wit-h-xhe requirements of Level C of MIL-STD-1169. 13 Provided by IHSNot for ResaleNo reproduction or networking permitted without lice

39、nse from IHS-,-,-a MIL-0-71152 99999Ob 1969222 bT5 = MIL-0-71152 (AR) 6. NOTES (This section contains informat-ion of a general or explanatory nature that may be helpful, but- i.s not mandatory.) 6.1 Intended use, The components covered by this specification are intended for assembly to M766 Practic

40、e Cartridges for use in the 60mm Mort-ar. 6.2 Acquisition requirements, Acquisit-ion documents must- specify the following: a. Title, number and date of this specificatj-on. b. Issue of DODISS t-o be cited in the solicitat.ion, and if required, the specifi-c issue of individual documents referenced

41、(see 2.1.2). c, Requirements for submission of first article sample. 6.3 Submission of contractor inspection equipment designs for approval. Submit copies of designs as required to: Commander, U.S. Army ARDEC, ATTN: SMCAR-QAT-I, Picatinny Arsenal, NJ 07806- 5000. This address will be specified on th

42、e Contract Data Requirements List, DD Form 1423 in the contract, 6.4 Submission of test data, One copy of proving ground ballistic acceptance test data (i.,e., firing record) shall be forwarded to each of the following: Commander, U.S. Army Armament Research, Development and Engineering Center, ATTN

43、: SMCAR-QAT-B, Bldg 62S, Picatinny Arsenal, NJ 07806-5000. 6.5 Submission of alternative quality conformance provjsions. All contractor proposed alternative quality conformance provisions will be submitted to the Government for evaluation/approval as direct.ed by the contracting activity. 14 Provide

44、d by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-* * MIL-O-7LLSZ 9999906 I1969223 531 MIL-0-71152 (AR) 6.6 Subject. term (keyword) - 1ist.ing. - Deflection temperature Flexural modulus Izod impact Ten s i 1 e st. r e ng t.h Custodian Army-AR Preparing activi t.y: Army-AR (Project. 1395-A267 ) 15 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-