ARMY MIL-M-64016 (3)-1998 MOTOR ROCKET METAL PARTS FOR AND LOADING ASSEMBLY FOR DEMOLITION KIT CRATERING M180《磨顶槽拆卸工具包用金属零件及其加载装置和火箭发动机 M180 t型》.pdf

《ARMY MIL-M-64016 (3)-1998 MOTOR ROCKET METAL PARTS FOR AND LOADING ASSEMBLY FOR DEMOLITION KIT CRATERING M180《磨顶槽拆卸工具包用金属零件及其加载装置和火箭发动机 M180 t型》.pdf》由会员分享，可在线阅读，更多相关《ARMY MIL-M-64016 (3)-1998 MOTOR ROCKET METAL PARTS FOR AND LOADING ASSEMBLY FOR DEMOLITION KIT CRATERING M180《磨顶槽拆卸工具包用金属零件及其加载装置和火箭发动机 M180 t型》.pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、MIL-M-64016 (3) 0b 2bbLL Lb IINCH-POUND I MIL-M-64016 (AR) AMENDMENT 3 27 March 1998 SUPERSEDING AMENDMENT 2 8 May 1984 MILITARY SPECIFICATION MOTOR, ROCKET, METAL PARTS FOR AND LOADING ASSEMBLY FOR DEMOLITION KIT, CRATERING: M180 This amendment forms a part of MIL-M-64016 (AR), dated 19 March 1983,

2、 and is approved for use by the U.S. Army Armament Research, Development and Engineering Center, and is available for use by all Departments and Agencies of the Department of Defense. PAGE 1 * 2.1.1, SPECIFICATIONS, MILITARY: Delete “MIL-P-117“ and substitute “MIL-B-117“. Delete specification MIL-1-

3、6868“ in its entirety. PAGE 2 * 2.1.1, SPECIFICATIONS, STANDARDS, MILITARY: Add new specification as follows: MIL-STD-1949 - Inspection, Magnetic Particle“. PAGE 8 4.4.2.1, Minor Defect: Delete 202 - Minor diameter of tapped holes (6)“. 1 of 3 AMSC N/A FSC 1375 DISTRIBUTION STATEMENT A. Approved for

4、 public release; distribution is unlimited. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-* * * MIL-M-64016 (AR) AMENDMENT 3 PAGE 10 4.4.2.3, Minor Defect: Delete “201 - Total length“. PAGE 11 4.4.2.4, Major Defect: Delete “102 - Total length“. PAG

5、E 12 4.4.2.5, Major Defect: Delete “107 - True position of head end I.D. with datum A“. PAGE 14 4.4.2.6, Minor Defect: Delete “201 - Rubberband missing“. PAGE 15 4.4.2.7: Major Defect: Delete 103 - Rubberband not removed from Major 101: Charge Assembly“. Delete in its entirety. Major 105, EXAMINATIO

6、N OR TEST: Delete in it entirety and substitute “Sealant not covering or not adhering to specified surfaces (igniter end)“. Add new Minor 204 as follows: “204 Height from retainer to edges of potting compound 0.65% 3.3 Gage“. PAGE 21 * 4.5.3, line 3: Delete “MIL-1-6868“ and substitute “MIL-STD-1949“

7、. 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- MIL-M-b40Lb (3) 0b 20bbL3 T89 m MIL-M-64016 (AR) AMENDMENT 3 The margins of this amendment are marked with an asterisk or vertical line to indicate where changes (additions, modifications, correcti

8、ons, deletions) from the previous amendment were made. This was done as a convenience only and the Government assumes no liability whatsoever for any inaccuracies in these notations. Bidders and contractors are cautioned to evaluate the requirements of this document based on the entire content irrespective of the marginal notations and relationship to the last previous amendment. Custodian: Amy-AR Preparing activity: Amy-AR (Project 1375 -0059 ) 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-