ARMY MIL-M-63287 (4)-1998 MINE ANTIPERSONNEL XM74 (M74) METAL PARTS FOR《杀伤地雷XM74(M74)金属零件》.pdf

《ARMY MIL-M-63287 (4)-1998 MINE ANTIPERSONNEL XM74 (M74) METAL PARTS FOR《杀伤地雷XM74(M74)金属零件》.pdf》由会员分享，可在线阅读，更多相关《ARMY MIL-M-63287 (4)-1998 MINE ANTIPERSONNEL XM74 (M74) METAL PARTS FOR《杀伤地雷XM74(M74)金属零件》.pdf（4页珍藏版）》请在麦多课文档分享上搜索。

1、t MIL-M-63287 (4) 9999906 2066232 559 IINCH-POUND I MIL-M-63287 (AR) AMENDMENT 4 27 March 1998 SUPERSEDING AMENDMENT 3 25 March 1985 MILITARY SPECIFICATION MINE , ANTIPERSONNEL , XM7 4 (M7 4 ) METAL PARTS FOR (MIL-M-63287 was inactivated after 17 July 1996 for New Design. I This amendment forms a pa

2、rt of MIL-M-63287 (AR), dated 24 July 1979, and is approved for use by the U.S. Army Armament Research, Development and Engineering Center, and is available for use by all Departments and Agencies of the Department of Defense. PAGE 1 Title: Add “(M74) after “XM74“; and wherever it appears in specifi

3、cation. 2.1, SPECIFICATIONS, MILITARY: Add the following new reference: “MIL-P-22332 - Paint, Priming, Exterior and Interior (For Ammunition) I. PAGE 2 STANDARDS: Add the following: “MIL-STD-171 - Finishing of Metal and Wood Surfaces.“ DRAWINGS (see 6.5): Delete l. . . COMMAND“ and substitute l. . .

4、 CENTER“. 2.2: Delete in its entirety. 1 of 4 AMSC N/A FSC 1345 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- - MIL-M-b3287 (Y) 9999906 2066233 Y95 MIL-M-63287 (AR)

5、AMENDMENT 4 PAGE 3 4.3.1: Line 10: Following “15“ add “(Plus 4 panels)“. Line 11: Delete “painting“ and substitute “primer coat“. From Previous Amendment 2: Delete the following: Bottom of page: Add L/ above panels for First Article are to be submitted to ARDC, DRSMC-QAT-M(D), AT“: PQM, Bldg. 62S, D

6、over, NJ 07801.“ Page 6 TABLE I: Line 8: Change “After n aintinq“ to “After nrimer coat“. Line 9: Change 15 (a) Ir to 15“. Line 10: After “. . .test“ and add “(panels)“. Change 15(a) “ to 4“. Change “ASTM B117“ to “MIL-P-22332“. Notes, line 1: Delete (a) These . . .assemblies.“ PAGE 9 4.4.2.2, Major

7、 103: Delete “(0.020)“. PAGE 10 4.4.2.3, Major 109: Delete “Outisde“ and substitute Outside“. PAGE 12 4.4.2.5: Add: Major 103 Inside diam. of cup (4 places), 0.40%, 3.2, Gage“. Add: “Major 104, Inside diam. of final assembly, 0.40%, 3.2, Gage“. 2 Provided by IHSNot for ResaleNo reproduction or netwo

8、rking permitted without license from IHS-,-,-MIL-M-6327 (4) rn 9999906 20bb234 321 rn MIL-M-63287 (AR) AMENDMENT 4 PAGE 15 4.4.2.8: Major 106: Following b“ add , (c)“. In No. of Sample Units column, insert 3“. Delete O. 40%“. Add: Major 107, Prior to welding, any surface of components improper for p

9、ainting, 0.40%, 3.2. MIL-STD-171.“ * Major 107, PARAGRAPH REFERENCE/INSPECTION METHOD: Delete “MIL - STD- 17 1 Ir and subs t i tut e “Vi sua 1 “ . Major 108, Following primer coating, I.D. of booster cavity undersize, 4 places, 0.40%, 3.2, Gage.“ Major 109, Following primer coating, I.D. of liner bo

10、oster Minor 201: Delete “Protective. . .diameter“ and substitute cup assembly undersize, 4 places, 0.40%, 3.2, Gage.“ “Primer coating on any outside surfaces. . .Ir Add: Minor 203, Diameter of fill holes undersize, (b), 0.65%, (d), gage“. Notes, (b) : Change “painting“ to primer coat“. Add “(cl Cut

11、off both ends of the three (3) case Add (a) See drawing 9292644.“ assemblies at liner ring and liner flange for internal visual examination. One defective case assembly rejects the lot.“ PAGE 19 6.3, line 4: Delete l. . . Command, ATTN: AMSMC-QAA-I,“ and substitute l. . . Center, ATTN: AMSMC-QAT-I(D

12、),“. PAGE 20 6.4, line 4: Delete l. . . Command, ATTN: AMSMC-QAA-M,“ and substitute I. . . Center, ATTN: AMSMC-QAT-M(D) , Ir. 6.5: Line 3: Delete l. . .Command (ARRADCOM) . . .“ and substitute l. . . Center (ARDC) . . . “ . Provided by IHSNot for ResaleNo reproduction or networking permitted without

13、 license from IHS-,-,-MIL-M-63287 (4) 9999906 20bb235 2b MIL-M-63287 (AR) AMENDMENT 4 Line 4: Delete as,” and substitute as US Army Armament Research and development Command (-COM) , l. Line 7: Delete “ARRADCOM. ” And substitute “ARDC. I. The margins of this amendment are marked with an asterisk or

14、vertical line to indicate where changes (additions, modifications, corrections, deletions) from the previous amendment were made. Government assumes no liability whatsoever for any inaccuracies in these notations. Bidders and contractors are cautioned to evaluate the requirements of this document ba

15、sed on the entire content irrespective of the marginal notations and relationship to the last previous amendment. This was done as a convenience only and the Custodian: Amy-A Preparing activity: Amy-= ( Proj ec t 13 45-003 3 ) 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-