ARMY MIL-L-50470 (1)-1988 LINER FOR DEEP CAVITY LOADED PROJECTILE《用于深腔弹丸的衬垫》.pdf

《ARMY MIL-L-50470 (1)-1988 LINER FOR DEEP CAVITY LOADED PROJECTILE《用于深腔弹丸的衬垫》.pdf》由会员分享，可在线阅读，更多相关《ARMY MIL-L-50470 (1)-1988 LINER FOR DEEP CAVITY LOADED PROJECTILE《用于深腔弹丸的衬垫》.pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、MIL-L-50470 (AR) AMENDMENT 1 16 FEBRUARY 1988 MILITARY SPECIFICATION LINER, FOR DEEP CAVITY LOADED PROJECTILE This Amendment forms a part of Military Specification MIL-L-50470 (MU), dated 14 January 1970 and is approved .for use within the Us Army Armament Munitions and Chemical Command and is avail

2、able for use by all departments .and Agencies of the Department of Defense. PAGE 1 2.1 Specifications, Military: Delete: “MIL-1-45607 - Inspection Equipment, Supply and Maintenance of“ Add: “MIL-A-48078 - Ammunition, Standard Quality Assurance Provisions, General Specification for“ Add the following

3、 note at the bottom of page: “Beneficial comments (recommendationd, additions, deletions) and any pertinent data which may be of use in improving this document should be addressed to: Commander I US Army Armament , Research , Development and Engineering Center, ATTN: AMSMC-QA, Dover, New Jersey 0780

4、1-5001 by us i ng the self- addr es sed S tandar di ?at i on Document Improvement Proposal (DD Form 1426) appearing at the end of this document or by letter.“ PAGE 2 2.1 Publications, Army: Delete: “ET-8797092 - Equipment Tabulation“ Add new paragraph 2.2 as follows: “2.2 Order of precedence. In the

5、 event of a conflict between the text of this specification and the reference cited her-ein, the text of this specification shall take precedence .“ - MC N/A 1 of 3 FSC i315 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited . -a- Provided by IHSNot for ResaleNo reprodu

6、ction or networking permitted without license from IHS-,-,-MIL-L-50470 (AR) AMENDMENT 1 4.1 Delete in its entirety and substitute the following: “4.1 Responsibility for inspection and standard quality assurance provisions. Unless otherwise specified herein or in the contract, the provisions of MIL-A

7、-48078 shall apply I and are hereby made a part of this detail specification.“ PAGE 3 4.1.1 c. Delete: “by defect code8“ PAGE 4 4.2.3 Delete in its entirety and substitute the following: “4.2.3 Rejection. - See MIL-A-48078.“ PAGE 5 4.3.2.1 Delete the last column “Code No.“ in its entirety. PAGE 6 4.

8、3.3, 4.3.3.1, 4.3.3.2 Delete in their entirety and substitute the following: “4.3.3 - Inspection equipment. The inspection equipment required to perform the examinations and tests perscribed herein is described in the “Method of Xnspect“in“ column in the table of paragraph 4.3.2.1. *he contractr Sha

9、ll submit for approval inspection equipment d6igns ln accordance with the terms of the contract. See Section a o MIL-24-48078 and 6. -herein.“ 6.1, 6.2r 6.38 6.3.1, 6.3.2, 6.3.3, 6.3.4 and 6.3.5 Delete in their entirety and substitute the foliowing: “6.1 rderinq data. See MIL-A-48678 (AR . 6.1.2 Dat

10、a card. bata cards re required and shall be prepared. See MIL-A-413078 (AR) i Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-5 - d MIL-L-50470 (2) 23 O 7777706 0327564 7 m MIL-L-50470 (AR) AMENDMENT 1 6.2 Submission of inspection procedures and equi

11、pment . desiqns for approval. See MIL-A-48078. Submit equipment .h.- t designs, as required, to: Research, Development. and Engineering Center, ATTN: AMMC-QAR-I (D) , Dover, New Jersey 07801-5001.“ Commander, US Army Armament, . Custodian: : Army - AR .Preparing Act i vi t y : (Project 1315-A815) Army - AR 3 - _ . - . - . . _ . Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-