ARMY MIL-L-47088-1974 LAMINATE ALUMINUM FOIL - POLYETHYLENE TEREPHTHALATE《铝箔片 聚对苯二甲酸乙二醇酯》.pdf

《ARMY MIL-L-47088-1974 LAMINATE ALUMINUM FOIL - POLYETHYLENE TEREPHTHALATE《铝箔片 聚对苯二甲酸乙二醇酯》.pdf》由会员分享，可在线阅读，更多相关《ARMY MIL-L-47088-1974 LAMINATE ALUMINUM FOIL - POLYETHYLENE TEREPHTHALATE《铝箔片 聚对苯二甲酸乙二醇酯》.pdf（6页珍藏版）》请在麦多课文档分享上搜索。

1、 I A-oq-/7 MIL-L-47088 (141) , 10 May 1974 MIS 14318 I 1 May 1965 v MI L I TART SPEC IF ICAT I ON LAMINATE, ALUMINUM FOIL - POLYETHYLENE TEREPHTHALATE 8 This specification is approved for use by all departments and agencies of the Department of Defense. -0 1. SCOPE 1.1 Scope. This specification cove

2、rs the require- . ments for one type of aluminum foil-polyethylene terephthalate lamina te, 2, APPLICABLE DOCUMENTS 2.1 Government documents-. The following documents, of the issue in effect on date of invitation for bids or request for proposal, form a part of this specification to the extent speci

3、fied herein. I SPEC IF ICATIONS Mil i tary M 1-1-631 -1nsulat ion, Electrical , Synthetic-Resin Composition, Nonrigid. FSC 9535 / THIS DOCUMENT CONTAINS 6 PAGES. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-L- 47088 (MI STANDARDS M IL - STD -

4、1 2 9 Marking for Shipment Storage (Copies of specifications, standards, drawings, and publications required by suppliers in connection with specific procurement functions should be obtained from the procuring activity or as directed by the contracting officer.) 2.2 Other publications, The following

5、 documents form a part of this specification to the-extent specified herein. Unless otherwise indicated, the issue in effect on date of invitation for bids or request for proposal shall apply! American Society for Testing and Materials ASTM D 373 Aluminum Foil for ASTM D 689 Tearing Resistance of Ca

6、pacitors, Specifications for Paper, Test for ASTM D 774 Bursting Strength of Paper, Test for ASTM D 828 Tensile Breaking Strength of Papex, Test for (Application for copies should be addressed to the American Society for Testing and Materials, 1916 Race Street, Philadelphia, Pennsylvania 19103,) .,.

7、 . Uniform Freiglt Classification Rules (Application for copies should be addressed to Uniform Classification Committee, 202 Chicago Union Station, Chicago, Illinois, 60U06.) 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-Provided by IHSNot for Re

8、saleNo reproduction or networking permitted without license from IHS-,-,-I 3.5 WorkmanshiD. The workmanship shall be such as this specification. seams, foreign matter or defects that may impair its serviceability. The material shall be free of delaminations, 4. OUALITY ASSURANCE PROVISIONS is respon

9、sible for the performance of all inspection-equire- ments as specified herein. Except as otherwise specified in the contract or order, the supplier may use his own or any other facilities suitable for the performance of the inspection requirements specified herein, unless disapproved by the Governme

10、nt. The Government reserves the right to perform any of the inspections set forth in the specification where such inspections are deemed necessary to assure supplies and services conform to prescribed requirements. I 4.2 Prenroduction samne. The memoduction samle preparation of subsequent production

11、 lots of material. Preproduction samples which do not meet all the require- ments of this specification shaii be subject to rejection and return to the supplier. I 4.3 Classification of examinations and test. The inspection and testing o the laminate shall be classified as follows : a. Preproduction

12、 tests. b. Quality conformance tests. I consist of all the examinations and tests specified herein. a, Visual examination, b. Thickness. part of one contract or order, and submitted for acceptance at the same time and place. I Provided by IHSNot for ResaleNo reproduction or networking permitted with

13、out license from IHS-,-,-5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-L-47088 (MI) rolls three inches inside diameter by 1/4 inch minimum wall thickness, core extending one inch beyond film on both ends, Each roll shall be individually wrapp

14、ed in two separate layers of soft textured material. a minimum of 1/8 inch thick and shall be backed by 30 or 40 pound wrapping paper, 5.2 Packing. Rolls shall be packed in shipping containers in a manner to insure carrier acceptance and safe delivery at destination at the lowest transportation rate

15、. Containers shall be in accordance with Uniform Freight Classification rules or National Motor Freight rules as applicable, 5.1 Packaging, The film shall be put on paper core Each layer shall be 5.3 Markin . Marking shall be in accordance with MIL- STD-129 an + as specified by procuring activity, 6

16、1 NOTES 6.1 Intended use. The laminate is interided for use as radio frequency interference shielding for electrical cables, 6.2 Ordering data, Procurement documents should specify the following: a. Title, number, and date of this specification, b, Whether a preproduction sample is required (see 3.1

17、) and if so, pertinent details, c, d, Sampling plan if other than specified (see 4,3,2.2), Width of laminate required and length of laminate on roll, 6.3 Su ersession data, This specification includes the requirements + o issmInterim Specification MIS-14318, dated 1 May 1965, Custodian: Preparing Activity: Army -M I Army -M I Project No. 9535-AO15 *U.C. GOVERNMENT PRINTING OFFICE: 1874-71516416606 6 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-