ARMY MIL-I-60350-1965 INERT FILLERS FOR USE IN AMMUNITION《用于惰性弹药的填料》.pdf

《ARMY MIL-I-60350-1965 INERT FILLERS FOR USE IN AMMUNITION《用于惰性弹药的填料》.pdf》由会员分享，可在线阅读，更多相关《ARMY MIL-I-60350-1965 INERT FILLERS FOR USE IN AMMUNITION《用于惰性弹药的填料》.pdf（8页珍藏版）》请在麦多课文档分享上搜索。

1、MIL-I-bo350 13 797970b O337897 7 m 1 I. MIL-I-63 5(MU) 30 OCTOBER 1965 MILITARY SPECIFICATION INERT FILLERS FOR USE IN AMMUNITION 1. SCOPE 1.1 Scope. This specification covers the types of inert fillers used in loading of stand- ard items of ammunition. 1.2 Classification. Inert Mers shall be of Typ

2、e I - Mixture of calcined gypsum, perlite and water. Type II -Mixture of the glyceride of 12 hydroxy stearic acid, rosin and dead burned gypsum with or without ferric oxide. Qpe III-Mixture of aluminum am- monium sulfate, cellulose or barium sulfate, copper sulfate and a corrosion in- hibitor. the f

3、ollowing compositions : 2. APPLICABLE DOCUMENTS 2.1 The following documents of the issue in effect on date of invitation for bid or request for proposal form a part of this specification to the extent specified herein. SPECIFICATIONS FEDERAL LLLR-626 - Rosin, O-A401 - Alum, Ammonia (Alu- minium, Amm

4、onium Sulfate), Technical. - O-G-828 . - Cupric Sulfate, Penta- . hydrate, Technical. PPP-D-723 - Drums, Fiber. MILITARY MIL-G2660 - General Specifications for Ammunition ex- cept Small Arms Ammunition. MIL-P-13800 - Perlite. MIL-STD-105 - Sampling Procedures and Tables for in- spection by Attri- bu

5、tes (ABCSTD- 105). . MILSTD-109 -Quality Assurance Terms and Defini- tions. MIGSTD-129 - Marking for shipment and storage. MILSTD-650 - Explosive : Sampling, Inspection and Test- ing. MIL-STD-1167- Ammunition Data Cards. MIL-SID-1235 - Single and Multilevel Continuous Sam- pling Procedures and Table

6、s for in- spection by Attri- butes, . PURCHASE DESCRIPTIONS (see 6.3) PA-PD-290 - Gypsum, Calcined. Licensed by Information Handling ServicesProvided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-1-60350 13 U 7979906 0337878 O U MIL-1-60350 (MU) PA-PD-6

7、66 - Iron oxide, Ferric. PA-PD-721 - Glyceride of 12-Hy- PA-PD-722 - Gypsum, dead burned. PA-PD-2765 - Cellulose, powdered. PA-PD-2766 - Barium sulfate. droxy stearic acid. (Copies of specifications, standards, drawings, and publications required by suppliers in connection with specific procurement

8、functions should be obtained from the procuring activity or as directed by the contracting officer.) 3.1.2 Trpes. Tllpe I Comtitrtcnt matcrial 3. REQUIREMENTS 3.1 Material, 3.1.1 Inert filler composition. The material in the inert filler compositions shall be in ac- cordance with applicable specific

9、ations cited in 3.1.2. The exact parts by weight indicated in 3.1.2 may be varied by the manufacturer; however, no ingredients other than those specified shall be utilized and no ingredients shall be omitted. Confmino to Parts by weight Calcined gypsum PA-PD-290 Perlite MIL-P-13800 Water Sodium Citr

10、ate TYPS ZI Comttuent materiai Confming to Glyceride of 12-hydroxy stearic acid PA-PD-721 Rosin LLGR-626, Type I, Grade FF Dead burned gypsum PA-PD-722 Ferric oxide PA-PD-656, Type II TW rix Constituent materiai Cmfomaino to Alum, Ammonia O-A401 (see 6.8) Powdered cellulose PA-PD-2766 Barium sulfate

11、 PA-PD2766 Acetone inhibitor No. 11 (see 6.9) Cupric sulfate 04-828 (see 6.10) Water 96 (see 6.6) 3-6 (see 6.6) 30 (see 6.6) (See 6.6) Parts bu weioht 36*1 6tl (See 6.7) (See 6.7) 100 (See 6.11) (See 6.11) 0.76 1 4 3.2 Specific Gravity. The specific gravity of the finished composition shall vary no

12、more than rc, 0.04 from that specified in the draw- ing or in the contract. 3.3 Workmanship. The composition shall be free of dirt, chips, grease, and other foreign matter, 4. QUALITY ASSURANCE PROVISIONS 4.1 General Quality Assurance Provisions. Unless otherwise specified in the contract or purcpas

13、e order, the supplier is responsible for -, 2 _ . the performance of all inspection require- ments specified herein. Except as otherwise specified, the supplier may utilize his own facilities or any commercial laboratory ac- ceptable to the Government. The Government reserves the right to perform an

14、y of the inspections set forth in the specification where such inspections are deemed necessary to assure supplies and services conform to prescribed requirements. Reference shall be made to Standard MIL-STD-109 in order to define terms used herein. The provisions of, Specification MIGA-2550 shall a

15、pply. , ,. . Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-I-bO350 13 977970b 4.1.1 Contractor qualitp assurance sgstem. If the contractor desires to utilize a quality assurance system, which is at variance with the quality assurance provisions

16、 of 4.2 and 4.3 and other documents referenced herein, he shall submit a written description of the system to the contracting officer for approval prior to initiation of production. It shall in- clude a description covering controls for lot formation and identification, inspections to be performed,

17、inspection stations, sampling pro- cedures, methods of inspection, (measuring and testing equipment), and provisions for control and disposition of nonconforming material. The written description will be con- sidered acceptable when, as a minimum, it provides the quality assurance provisions re- qui

18、red by the provisions of 4.2 and 4.3 and other documents referenced herein. The con- tractor shall not be restricted to the inspec- tion station or the method of inspection listed in this specification provided that an equivalent control is included in the approved quality assurance procedure. In ca

19、ses of dis- pute as to whether certain procedures of the contractors system provide equal assurance, the comparable procedures of this specifica- tion shall apply. The contractor shall notify the Government, of and obtain approval for, any changes to the written procedure effects the degree of assur

20、ance required by this spec- ification or other documents referenced herein. 4.1.2 Szibmission of product. At the time the completed lot of product is submitted to the Government for acceptance the contrac- tor shall supply the following information accompanied by a certificate which attests that the

21、 information provided is correct and applicable to the product being submitted : (a) A statement that the lot complies with all requirements and provi- sions of the approved current written description of the filler. (b) Specification number and date, to- gether with an identification and date of ch

22、anges. 0337899 2 H MILI40350 (MU) (c) Certificates of analysis on all mate- -. rial used directly by the con- tractor when such material is controlled by Government speci- fication, shall be made available upon request by the contracting officer, (d) Quantity of product in the lot. (e) Date submitte

23、d. The certificate shall be signed by a respcnsi- ble agent of the certifying organization. The initial certificate submitted shall be substan- tiated by evidence of the agents authority to bind his principal. Substantiation of the agents authority will not be required with subsequent certificates u

24、nless, during the course of the contract this authority is vested in another agent of the certifying organization. 4.1.3 Government verification. Using the contractors written quality assurance proce- dure, (see 4.1.1) this detail specification, and Gther contractual documents as a guide, the Govern

25、ment shall verify all quality assurance operations performed by the contractor, Verification shall be in accordance with (a) or (b) as applicable, the decision being the responsibility of the procuring activity, In either case, the inspector shall also ascertain, prior to acceptance that all quality

26、 provisions of other specifications referenced in any of the contractual documents have been com- plied with. Deviations from prescribed or agreed upon procedures discovered by the Government inspector shall be brought to the attention of the supplier. Disposition of the product and remedial action

27、shall be as directed by the Government inspector and, depending on the nature of the deviation, may consist of lot rejection, screening, re- sampling, re-instruction or the suppliers employees, or other appropriate action : (a) Verification at the point of manu- facture shall be accomplished at unsc

28、heduled intervals in accord- ance with 4.1.3.1 and 4.1.32. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- MIL-I-b0350 13 77777Ob 0337700 5 M. MILI-60350 (MU) (b) Verification at the point of delivery shall be in accordance with 4.1.3.2. 4.1.3.1 Sur

29、veillance. Surveillance shall in- (a) Observation of procedures concern- ing lot formation and identifica- tion. clude, but is not limited to: (b) Observation of sampling procedures and application of acceptance cri- teria. (c) Determinations that all required ex- aminatims and tests are per- formed

30、 in accordance with the prescribed procedures of this specification, or approved equiva- lents thereto, (a) Review of procedures for control and disposition of nonconforming material, 4.2 Inspection provisions. 4.2.1 Lot formation. A lot shall consist of one or more batches of the inert filler pro-

31、duced by one manufacturer in accordance with the same specification, or same specifi- cation revision under one continuous set of operating conditions. Each batch shall con- sist of that quantity of the inert filler that has bean subjected to the same unit chemical or physical mixing process intende

32、d to make the final product homogeneous. The product shall be submitted for inspection in accord- ance with Standard MIGSTD-105 (or Standard MILSTD-1235 when applicable). 4.2.2 Examination. Sampling plans and procedures for the following specification of defects shall be in accordance with Standard

33、MIL-STD-106. Continuous sampling plans, in accordance with Standard MILSTD-1235 may be used if approved by the procuring activity. Also, at the option of the procuring activity, AQ,Ls and sampling plans may be applied to the individual characteristics listed using an AQL of 0.40 percent for each maj

34、or defect and an AQL of 0.65 percent for each minor defect, 4.2.2.1 Dmims, prior to filling (Polyethylene liner). Catcaorka Defeck Method Of inspection Critical: None defined. Major: AQL 0.40 percent Minor: None defined. 101. Liner cut, torn or punctured Visual 4.2.2.2 Drums, prior to closing (Polye

35、thylene liner). Categoricr Defeck Method of inspection Critical: None defined. Major: AQL 0.40 percent Minor: None defined. 101. Liner not completely sealed . Visual 4.2.2.3 Drum, sealed (fiber). Categorca Dcfeck Method of inspection Critical: None defined. Major: AQL 0.40 percent 101, Weight of con

36、tents scale 102. Closure incomplete or damaged to the extent that contents sift out . Visual 201. Minor: AQL 0.65 percent Markings misleading or unidentifiable Visual 4 Code ho. (aee 6.11) O1001 Code NO. 02001 Code &o. 03001 03002 03003 Provided by IHSNot for ResaleNo reproduction or networking perm

37、itted without license from IHS-,-,- MIL-I-b0350 13 77777Ob 0337703 7 4.2.3 Testhg. A 10- to 15-gram specimen of the cast inert filler shall be selected from each batch produced and tested in accordance with the test specified in 4.3.1. If the sample fails to comply with the specific gravity spec- if

38、ied on the drawing or in the contract, the batch shall be rejected. 4.3 Test methods. 4.3.1 Specfy gravity. Code No. 05001. De- termine the specific gravity of the cast inert fillers in accordance with Method 203.1 de- scribed in Standard MIL-STD-650. 5. PREPARATION FOR DELIVERY 5.1 Packing. 5.1.1 D

39、ntms. Unless otherwise specified in the contract or purchase order, the inert filler shall be packed in nonreturnable fiber drums in accordance with Specification PPP-D-723 (Type III, Grade A), The drums shall be fin- ished with a nominal 0.004 inch thick poly- ethylene liner, properly heat sealed o

40、r other- wise closed to afford protection to the con- tents equivalent to that given by a heat seal closure. 5.1.2 Level C. The inert filler shall be packed to afford protection against damage during direct shipment from supply source to the fmt receiving activity for immediate use. Containers shall

41、 comply with Uniform Freight Classification Rules and Container Specifications for rail shipments or National Motor Freight Rules and Container Specifi- catons for truck shipment as applicable. 5.2 Marking. In addition to any special marking required by the contract or pur- chase order, containers s

42、hall be marked in accordance with MILSTD-129. Marking shall include, but not limited to, the follow- ing information : (a) Manufacturers name. (b) Product designation. MILI-60350 (MU) (c) Lot number, (d) Date of manufacture, (e) Number of this specification. 6. NOTES 6.1 Ordering data. Procurement d

43、ocuments (a) Title, number, and date of specifica- tion. (b) Type required. (c) Ammunition data cards shall be prepared in accordance with Standard MILSTD-1167. should specify the: 6.2 Intended use. The materials described in this specification are intended to be used as inert fiilers in place of ex

44、plosives in artil- lery shells as well as other standard items of ammunition. 6.2.1 Type I filler simulates such high ex- plosives as composition B and 80/20 Tritonal. 6.2.2 Type II filler simulates such high ex- plosives as I“, Composition B, 52/48 Picra- tol, 76/25 Cyclotol, 80J20 Tritonal, HBX-1,

45、 HBX-3 and HBX-6. 6.2.3 Type III filler simulates explosives having specific gravity from 1.5 to 1.95. 6.3 PA-PD documents. These documents are purchase descriptions prepared by Pica- tinny Arsenal, Dover, N. J. 6.4 Compatibility with explosives. Type III filler is compatible with TNT, RDX, and HMX.

46、 6.5 The proportions given are approximate. These proportions have to be varied to pro- duce an inert filler of the specific gravity prescribed on applicable drawing. 6.6 The addition of not more than 0.01 grams of Sodium Citrate for each pound if 5 Provided by IHSNot for ResaleNo reproduction or ne

47、tworking permitted without license from IHS-,-,-NIL-I-bo350 13 M 3999906 0337702 9 Alum 1: 90 85 80 76 MIL140350 (MU) :Il Cellulose BaSO . 4 a. . 10 15 _._ 20 ._._ 26 calcined- gypsum in Type I filler is permissible to increase the time of pourability. 6.7 The parta by weight of dead burned gypsum a

48、nd ferric oxide shall be varied in the proportion necessary to produce a 611er of the weight prescribed on the applicable drawing. To assist in determining the parts by weight of dead burned gypsum to be re- placed by ferric oxide necessary to meet the weight requirement specified on the appli- cabl

49、e drawing, reference may be made to figure 1. This figure indicates the approxi- mate specific gravity produced by the nomi- nal combination of constituents. TAELE 1. Relat?onsh.ip between composition and specific gravity Type III Filler Composition, % I Custodian: Army-MU Specific gravity 1.65 1.58 1.60 1.71 1.77 1.85 1.95 6.8 A rice size has been found more suit- able than the nut size described in specifica- tion. 6.9 Actane inhibitor, No. 11 is a pr