ARMY MIL-G-45653 (2)-1983 GAGES CYLINDRICAL PLUG AND RING PLAIN《圆柱形插头和环平面压力计》.pdf

《ARMY MIL-G-45653 (2)-1983 GAGES CYLINDRICAL PLUG AND RING PLAIN《圆柱形插头和环平面压力计》.pdf》由会员分享，可在线阅读，更多相关《ARMY MIL-G-45653 (2)-1983 GAGES CYLINDRICAL PLUG AND RING PLAIN《圆柱形插头和环平面压力计》.pdf（2页珍藏版）》请在麦多课文档分享上搜索。

1、MIL-G-qSb53 (2) 52 M 7797706 03b77L O M MIL-G-45653 Al4ENDMENT 2 8 June 1983 SUPERSEDING AMENDMENT 1 18 Sep 1961 MILITARY SPECIFICATION GAGES, CYLINDRICAL PLUG AND RING, PLAIN This amendment forms a part of Military Specification MIL-G-45653, dated 30 December 1959, and is approved for use by all De

2、partments and Agencies of the Department of Defense. PAGE 1 Under STANDARDS: Delete “MIL-STD-10 -Surface Roughness Waviness and Lay.“ PAGE 2 * 2.2, lines 5-6: Delete “U.S. DEPARTMENT OF COMMERCE Commercial Standard CS8 , Gage Blanks“ and substitute “AMERICAN NATIONAL STANDARD INSTITUTE (ANSI) ANSI B

3、47.1-1981 , Gage Blanks“ 2.2, lines 7-8: Delete “Supplement to Commercial Standard CS8.“ * 2.2, lines 7-8: Add “ANSI B46.1-1978 -Surface Texture (Surface Roughness Waviness and Lay) .I * 2.2, lines 9-11: Delete “(Application for copies should be addressed to the Superintendent of Documents, U.S. Gov

4、ernment Printing Office, Washington 25, D.C.)“ and substitute “(Application for copies should be addressed to the American National Standard Institute, 1430 Broadway New York, N.Y. 10018)“ * 2.2, line 12: Delete “Consolidated“ and substitute “Uniform.“ * 2.2, lines 16-18: Delete “Consolidated Classi

5、fication Committee, 202 Chicago Union Station, Chicago 6, Ill.“ and substitute “Uniform Classi- fication Committee, Room 1106, 222 South Riverside Plaza, Chicago, IL 60606“ * 2.2, lines 24-25: Delete “1424 Sixteenth Street, N.W. Washington 6, D.C.“ and substitute “1616 P Street N.W., Washington, DC

6、20036“ * 3.1.1 , line 3: Delete “Commercial Standard CS8“ and substitute !ANSI 847.1“ 3.1.1, lines 3-4: Delete “and the Supplement to Commercial Standard CS8.“ 1 of 2 FSC 5220 9-= y, Licensed by Information Handling ServicesProvided by IHSNot for ResaleNo reproduction or networking permitted without

7、 license from IHS-,-,-PAGE 3 _. 1 * 3.1.3.1, lines 4-5: Delete “Standard MIL-STD-10“ and substitute “ANSI B46.1“ * 3.2.1, line 3: Delete “Commercial Standard CS8“ and substitute “ANSI B47.1“ 3.2.1, lines 3-4: Delete “and the Supplement to Comercial Standard CS8“ 3.2.4, lines 2-4: Delete “of type No.

8、 2 as illustrated in the 1955 Supple- ment to Commercial Standard CS8.“ * 3.2.5.2, lines 2-3: Deletellas shown in Commercial Standard CS8.“ NOTE: The margins of this amendment are marked with an asterisk to indicate where changes from the previous amendment were made. This was done as a convenience

9、only and the Government assumes no liability whatsoever for any inaccuracies in these notations. Bidders and contractors are cautioned to evaluate the requirements of this document based on the entire content irrespective of the marginal notations and relationship to the last previous amendment. Custodian: Army - AR 2 Preparing activity : Army - AR (Project 5220-A201) Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-