ARMY MIL-DTL-53126 3 A-2012 POWER DISTRIBUTION ILLUMINATION SYSTEMS ELECTRICAL DISTRIBUTION SYSTEM 40 AMPS PHASE (A P) [Superseded ARMY MIL-E-53126 REINST NOTICE 3 ARMY MIL-E-53126.pdf

《ARMY MIL-DTL-53126 3 A-2012 POWER DISTRIBUTION ILLUMINATION SYSTEMS ELECTRICAL DISTRIBUTION SYSTEM 40 AMPS PHASE (A P) [Superseded ARMY MIL-E-53126 REINST NOTICE 3 ARMY MIL-E-53126.pdf》由会员分享，可在线阅读，更多相关《ARMY MIL-DTL-53126 3 A-2012 POWER DISTRIBUTION ILLUMINATION SYSTEMS ELECTRICAL DISTRIBUTION SYSTEM 40 AMPS PHASE (A P) [Superseded ARMY MIL-E-53126 REINST NOTICE 3 ARMY MIL-E-53126.pdf（7页珍藏版）》请在麦多课文档分享上搜索。

1、 AMSC N/A FSC 6150 Distribution Statement A. Approved for public release, distribution is unlimited. PAGE 1 OF 7 INCH-POUND MIL-DTL-53126/3A 16 OCTOBER 2012 SUPERSEDING MIL-E-53126(ME) 20 April 1992 DETAIL SPECIFICATION SHEET POWER DISTRIBUTION, ILLUMINATION SYSTEMS, ELECTRICAL DISTRIBUTION SYSTEM,

2、40 AMPS/PHASE (A/P) This specification is approved for use within US Army Research Development and Engineering Command, Communications and Electronics Research and Development Center, Product Realization Directorate, Department of the Army and is available for use by all Departments and Agencies of

3、the Department of Defense. The requirement for acquiring the product described herein shall consist of this specification sheet and MIL-DTL-53126. 1. SCOPE 1.1. Scope. This specification sheet covers the detail requirements for the Power Distribution Illumination Systems Electrical (PDISE), Type III

4、, model: M40. 2. APPLICABLE DOCUMENTS 2.1. Drawings. The following Government drawings form a part of this specification sheet to the extent specified herein. Unless otherwise specified, the issues are those cited in the solicitation. DRAWING# NOMENCLATURE DRAWING # NOMENCLATURE CECOM & PM-MEP Drawi

5、ngs - Cage Code: 97403 and 30554 13229E6353 Distribution System, Electrical, Three Phase, 40 Amperes/Phase 13229E6357 Connector Assembly 40 AMP/PH Input Plug Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-53126/3A PAGE 2 OF 7 (Copies of draw

6、ings required by contractors in connection with specific acquisition functions should be obtained from: PROJECT MANAGER-MOBILE ELECTRIC POWER, 5850 Delafield Road, Bldg 324 FT BELVOIR VA 22060-5809.) 3. REQUIREMENTS 3.1. Requirements. The M40 PDISE shall be a self-contained, free-standing, man porta

7、ble unit. The system shall be capable of distributing 40 A/P of electricity to all its outputs simultaneously, as specified herein. Type IV 40 A/P distribution system3.2. Design. The M40 PDISE shall be IAW TA13229E6353 and as specified herein. 3.2.1. Dimensions. The M40 PDISE shall not be greater th

8、an the following dimensions: Length (Inches) Width (Inches) Height (Inches) 25.00 19.00 18.00 3.2.2. Weight. The M40 PDISE shall weigh no more than 50 pounds. 3.2.3. M40 PDISE Inputs. The M40 PDISE shall have a single 3-phase input capable of handling 40 A/P. Provided by IHSNot for ResaleNo reproduc

9、tion or networking permitted without license from IHS-,-,-MIL-DTL-53126/3A PAGE 3 OF 7 3.2.3.1. Input circuit interrupter. The input circuit for the M40 PDISE shall be protected from overload by a properly sized circuit breaker. The circuit breaker shall act as a switch to activate/deactivate the ci

10、rcuit. 3.2.3.2. Input Connector. The M40 PDISE shall have a 40 ampere, three phase, male, input receptacle IAW 13229E6357. 3.2.4. M40 PDISE Outputs The M40 PDISE shall have the following output circuits and connectors: Quantity Output Rating Ouput Connector P/N* 1 40Amp, 3 phase M90556C32413P 12 20

11、Amp, 3 phase M3406D16-10S *Note: See 3.3.16.1 in MIL-DTL-53126. 3.2.4.1. Output circuit interrupters. Each output circuit shall be protected by a properly sized circuit breaker. The circuit breaker shall act as a switch to activate/deactivate the circuit. 3.2.5. Type III accessories. The unit shall

12、be provided with the following accessories: Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-53126/3A PAGE 4 OF 7 Quantity Description Reference* 1 Input interface cable assembly, rated at 40/60 amperes 3.3.18.1* 2 40/60 A/P cable assemblies 3

13、.3.18.4* 3 20 A/P cable assemblies (25 0.25 feet long) 3.3.18.6* 3 20 A/P cable assemblies (50 0.25 feet long) 3.3.18.6* 2 Transition cable assemblies 3.3.18.8* 4 Single strap assemblies 3.3.19.2* 6 Cinching Strap 3.3.91.1* 1 Receptacle assembly 3.3.17* 1 In-Line GFCI 3.3.18.10* 1 Container 2.1 *Not

14、e: See requirement paragraph referenced MIL-DTL-53126. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-53126/3A PAGE 5 OF 7 2.00 MAX10.752.50CARRYINGSTRAP20.751.50MARKING TAG(WHITE)CINCHINGSTRAP3.2.6. Wiring diagram. The circuits shall be con

15、figured as specified in the following wiring diagram: Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-53126/3A PAGE 6 OF 7 C B A J2 J2C4L3 J2B4L2 J2A4L1 J2N4NEUT J2G6GND N G OUTPUT 40 A 3 PHASE L3 BB BB L2 L1 BB NEUT BB BB GND CB1 INPUT 40 A

16、3 PHASE J1A4CB1A J1B4CB1B J1C4CB1C J1G6GND J1N4NEUT A B C J1 G N CB1A CB1B CB1C CB1A4L1 CB1B4L2 CB1C4L3 A B C J3 OUTPUT 20 A 1 PHASE CB3 J3A12CB3 J3B12NEUT J3C12GND CB312L3 A B C J5 OUTPUT 20 A 1 PHASE CB5 J5A12CB5 J5B12NEUT J5C12GND CB512L2 A B C J7 OUTPUT 20 A 1 PHASE CB7 J7A12CB7 J7B12NEUT J7C12G

17、ND CB712L1 CB9 20 A 1 PHASE OUTPUT J9 C B A J9C12GND J9B12NEUT J9A12CB9 CB912L3 A B C J11A12CB11 J11B12NEUT J11C12GND J11 OUTPUT 20 A 1 PHASE CB1CB1112L2 CB13 20 A 1 PHASE OUTPUT J13 J13C12GND J13B12NEUT J13A12CB13 C B A CB1312L1 CB4 C B A J4 J4C12GND J4B12NEUT J4A12CB4 OUTPUT 20 A 1 PHASE CB412L3 C

18、B6 C B A J6 J6C12GND J6B12NEUT J6A12CB6 OUTPUT 20 A 1 PHASE CB612L2 CB8 C B A J8 J8C12GND J8B12NEUT J8A12CB8 OUTPUT 20 A 1 PHASE CB812L1 J10 A B C CB10 J10A12CB10 J10B12NEUT J10C12GND OUTPUT 20 A 1 PHASE CB1012L3 CB12 C B A J12C12GND J12B12NEUT J12A12CB12 J12 OUTPUT 20 A 1 PHASE CB1212L2 DS1CB1A DS2

19、CB1B DS3CB1C DS3 DS2 DS1 DS1NBB DS2NBB DS3NBB LIGHT BRACKET CIRCUIT BREAKER MOUNTING PANEL TOP COVER CHASSIS GROUND CB14 J14 OUTPUT 20 A 1 PHASE CB1412L1 C B A J14C12GND J14B12NEUT J14A12CB14 3.2.7 This specification sheet had no superseding “base”. The original publication of this specification was

20、 a performance specification that was used in-house by CR4. Since this specification is now a detailed military specification, this specification sheet is deemed necessary to capture the unique characteristics desired in the end item. 3.2.8 Changes from previous issues: Marginal notations are not us

21、ed in this revision to identify changes with respect to the previous issue because this detail specification sheet although a part of the base document, was not published because it was a document with limited circulation and coordination that was used essentially by CR4. Provided by IHSNot for Resa

22、leNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-53126/3A PAGE 7 OF 7 Concluding Material Custodian: Preparing Activity: Army - CR4 Army - CR4 (Project 6150-2012-012) Review Activities: DLA GS Note: The activities listed above were interested in this document as of the date of this document. Since organization and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-