ARMY MIL-DTL-46594 C-2011 CHARGE DEMOLITION SHAPED 40 LB M3A1 LOADING ASSEMBLING AND PACKING.pdf
《ARMY MIL-DTL-46594 C-2011 CHARGE DEMOLITION SHAPED 40 LB M3A1 LOADING ASSEMBLING AND PACKING.pdf》由会员分享,可在线阅读,更多相关《ARMY MIL-DTL-46594 C-2011 CHARGE DEMOLITION SHAPED 40 LB M3A1 LOADING ASSEMBLING AND PACKING.pdf(16页珍藏版)》请在麦多课文档分享上搜索。
1、 AMSC N/A FSC 1375 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. MIL-DTL-46594C(AR) 11 September 2011 SUPERSEDING MIL-C46594B(AR) w/AMENDMENT 214 JUNE 1991 DETAIL SPECIFICATION CHARGE, DEMOLITION, SHAPED, 40 LB. M3A1 LOADING, ASSEMBLING AND PACKING This specificat
2、ion is approved for use by U.S. Army Armament Research, Development and Engineering Center (ARDEC) and is available for use by all Departments and Agencies of the Department of Defense. 1. SCOPE 1.1 Scope. This specification covers the loading, assembling and packing for one type of demolition kit d
3、esignated as Charge, Demolition, Shaped, 40 lb., M3A1. 2. APPLICABLE DOCUMENTS 2.1 General. The documents listed in this section are specified in sections 3 and 4 of this specification. This section does not include documents in other sections of this specification or recommended for additional info
4、rmation or as examples. While every effort has been made to ensure the completeness of this list, document users are cautioned that they must meet all requirements documents cited in sections 3 and 4 of this specification, whether or not they are listed. 2.2 Government documents. 2.2.1 Specification
5、s, standards, and handbooks. The following specifications, standards and handbooks form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those specified in the solicitation or contract. Comments, suggestions, or questions on this d
6、ocument should be addressed to Commander ARDEC, ATTN: RDAR-QES-E, Picatinny Arsenal, New Jersey 07806-5000 or emailed to aredecstdznconus.army.mil. Since contact information can change, you may want to verify the currency of this address information using the ASSIST Online database at https:/assist.
7、daps.dla.mil.INCH-POUND Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-46594C(AR) DEPARTMENT OF DEFENSE STANDARDS AND SPECIFICATIONS MIL-STD-1168 - Ammunition Lot Numbering and Ammunition Data Card MIL-STD-1916 - DOD Preferred Method for Acc
8、eptance of Product MIL-DTL-12560 - Armor Plate, Steel, Wrought, Homogeneous (for use in combat-vehicles and for ammunition testing) (Copies of these documents are available online at https:/assist.daps.dla.mil/quicksearch/ or from the Standardization Document Order Desk, 700 Robbins Avenue Bldg. 4D,
9、 Philadelphia, PA 19111-5-94.) 2.2.2 Other Government documents, drawings and publications. The following other Government documents, drawings and publications form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in th
10、e solicitation (see 6.2). ARDEC Drawings 7549165 - Box, Packing, Ammunition, for Charge, Demolition, Shaped, 40 lb., M3A1 7549166 - Support, Packing, Ammunition, for Charge, Shaped, 40 lb., M3A1 8858390 - Charge, Demolition, Shaped, 40 lb., M3A1 8858382 - Charge, Demo, Shaped, 40 lb., M3A1, Metal Pa
11、rts Assembly 8858393 - Booster (Copies of these drawings are available from US Army ARDEC, AMSRD-AAR-AIS-TD, Picatinny, NJ 07806-5000, or online from Drawing-Requestus.army.mil.) 2.3 Non-Government publications. The following documents form a part of this document to the extent specified herein. AST
12、M INTERNATIONAL ASTM E1742/E1742M - Standard Practice for Radiographic Examination (Copies of ASTM standards may be ordered online at http:/www.astm.org/ or from the ASTM International, 100 Barr Harbor Drive, Conshohocken, PA 19428-2959.) NATIONAL AEROSPACE STANDARDS NAS 410 - NAS Certification and
13、Qualification of Nondestructive Test Personnel 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-46594C(AR) (Copies of NAS documents may be ordered at http:/aero- or from the Aerospace Industries Association of America, 1000 Wilson Blvd., Arl
14、ington, VA 22209.) 2.4 Order of precedence. In the event of a conflict between the text of this document and the references cited herein, the text of this document takes precedence. Nothing in this document, however, supercedes applicable laws and regulations unless a specific exemption has been obt
15、ained. 3. REQUIREMENTS 3.1 First Article. When specified, a sample shall be subjected to first article inspection in accordance with 4.2. 3.1.1 Radiographic examination. Radiographic examination, in accordance with 4.3.3.3 and 6.5, shall be conducted on First Article samples that are to be subjected
16、 to the Functioning Test, prior to the execution of the Functioning Test (see Table II). Radiographic examination data shall not be used to accept/reject this system. 3.2 Material. Materials, parts and assemblies shall comply with all requirements specified on the applicable drawings and referenced
17、specifications. 3.3 Assemblies. The assemblies shall comply with all requirements specified on applicable drawings and with all requirements specified in the applicable specifications. 3.4 Functioning Test. The loaded assembly shall function satisfactorily as evidenced by high-order detonation of th
18、e charge and penetration of a target of Rolled Homogeneous Armor (RHA) in accordance with MIL-A-12560, Class 1 or 2. The RHA target shall be of a size not less than four inches total thickness and surface area not less than 144 square inches, with any number of plates to make up that size. The penet
19、ration hole in the plate shall exhibit no evidence of double- or multi-jets. This test shall be performed as specified in 4.3.3.4. 3.5 Workmanship. Loading and assembling shall be accomplished in a thorough workmanlike manner. All parts and assemblies shall be clean and free of explosive on exterior
20、, chips, cracks, crazes, dirt, grease, rust, corrosion products, and other defects and foreign matter which would affect their serviceability. The cleaning method used shall not be injurious to any part or assembly nor shall the cleaning agent contaminate them. Exterior surface coatings shall be con
21、tinuous. All required markings shall be neat and sharply defined. Required packing shall be dry. 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-46594C(AR) 4. VERIFICATION Table I. REQUIREMENTS/VERIFICATION CROSS REFERENCE MATRIX Method of
22、Verification Classes of Verification 1- Analysis 2- Demonstration (end item test) 3- Examination 4- Test A - First Article B - Conformance Section 3 Requirements Description Verification Method Verification Class Section 4 1 2 3 4 A B 3.1 First Article X X X X 4.2 3.1.1 X-ray examination X X X 4.3.3
23、.3 3.2 Material X X X X X 4.3 3.3 Assemblies X X X X 4.3 3.4 Functioning Test X X X 4.3 3.5 Workmanship X X X X X 4.3 4.1 Classification of Verification. The verification requirements specified herein are classified as follows: a. First Article Inspection (see 4.2) b. Conformance Inspection (see 4.3
24、) 4.2 First article inspection. 4.2.1 Submission. When specified, a first article sample shall be submitted for evaluation in accordance with the provisions of 4.2.2 and Table II. 4.2.2 Inspections to be performed. As determined by the Government, the first article samples may be subjected to any or
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ARMYMILDTL46594C2011CHARGEDEMOLITIONSHAPED40LBM3A1LOADINGASSEMBLINGANDPACKINGPDF
链接地址:http://www.mydoc123.com/p-444334.html