ARMY MIL-DTL-45322 J-2010 DOLLY TRAILER CONVERTERS M197A1 M198A1 AND M354《M197A1型 M198A1型和M354型手推车和拖车转换装置》.pdf

《ARMY MIL-DTL-45322 J-2010 DOLLY TRAILER CONVERTERS M197A1 M198A1 AND M354《M197A1型 M198A1型和M354型手推车和拖车转换装置》.pdf》由会员分享，可在线阅读，更多相关《ARMY MIL-DTL-45322 J-2010 DOLLY TRAILER CONVERTERS M197A1 M198A1 AND M354《M197A1型 M198A1型和M354型手推车和拖车转换装置》.pdf（16页珍藏版）》请在麦多课文档分享上搜索。

1、 Comments, suggestions, or questions on this document should be addressed to U.S. Army RDECOM, Tank Automotive Research, Development and Engineering Center, ATTN: RDTA-EN/STND/TRANS MS #268, 6501 E. 11 Mile Road, Warren, MI 48397-5000 or emailed to DAMI_STANDARDIZATIONconus.army.mil. Since contact i

2、nformation can change, you may want to verify the currency of this address information using the ASSIST Online database at https:/assist.daps.dla.mil. AMSC N/A FSC 2330 INCH-POUND MIL-DTL-45322J 16 July 2010 SUPERSEDING MIL-DTL-45322H 4 September 1998 DETAIL SPECIFICATION DOLLY, TRAILER CONVERTERS,

3、M197A1, M198A1 AND M354 This specification is approved for use by all Departments and Agencies of the Department of Defense. 1. SCOPE 1.1 Scope. This specification covers M197A1, M198A1 and M354 tactical dollies for use in converting various semitrailers to full trailers. 1.2 Classification. Dollies

4、 will be of the following models as specified (see 6.2 and 6.4). Dollies will also be referred to herein as “vehicles”. Model Description M197A1 Dolly, trailer convertor, 6 ton, 2 wheel M198A1 Dolly, trailer convertor, 8 ton, 2 wheel M354 Dolly, trailer convertor, 15 ton, 4 wheel 2. APPLICABLE DOCUM

5、ENTS Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-45322J 2 2.1 General. The documents listed in this section are specified in sections 3, 4, or 5 of this standard. This section does not include documents cited in other sections of this sta

6、ndard or recommended for additional information or as examples. While every effort has been made to ensure the completeness of this list, document users are cautioned that they must meet all specified requirements of documents cited in sections 3, 4, or 5 of this standard, whether or not they are li

7、sted. 2.2 Government documents. 2.2.1 Specifications, standards, and handbooks. The following specifications, standards, and handbooks form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contrac

8、t. (see 6.2). COMMERICAL ITEM DESCRIPTIONS A-A-50271 - Plates, Identification, Instruction and Marking, Blank DEPARTMENT OF DEFENSE SPECIFICATIONS MIL-DTL-53039 - Coating, Aliphatic Polyurethane, Single Component, Chemical Agent Resistant MIL-DTL-64159 - Coating, Water Dispersible Aliphatic Polyuret

9、hane, Chemical Agent Resistant. (Copies of these documents are available from https:/assist.daps.dla.mil/quicksearch/ or from Document Automation and Production Service, Building 4/D, 700 Robbins Avenue, Philadelphia, PA 19111-5094) 2.2.2 Other Government documents, drawings, and publications. The f

10、ollowing other Government documents, drawings, and publications form a part of this document to the extent specified herein. Unless otherwise specified, the issues are those cited in the solicitation (see 6.2). FEDERAL MOTOR VEHICLE SAFETY STANDARDS (FMVSS) 49CFR571.105 - Hydraulic and Electric Brak

11、e Systems (Copies of these documents are available from www.gpoaccess.gov/cfr/index.html or U.S. Government Printing Office, P.O. Box 979050, St. Louis, MO 63197-9000.) U.S. ARMY TACOM DRAWINGS 8736120 - Dolly, Trailer Converter, 6 Ton, 2 Wheel, M197A1 Provided by IHSNot for ResaleNo reproduction or

12、 networking permitted without license from IHS-,-,-MIL-DTL-45322J 3 8736124 - Dolly, Trailer Converter, 8 Ton, 2 Wheel, M198A1 8736308 - Dolly, Trailer Converter, 15 Ton, 4 Wheel, M354 (Copies of these documents are available from DAMI_STANDARDIZATIONconus.army.mil or U.S. Army RDECOM, Tank Automoti

13、ve Research, Development and Engineering Center, ATTN: RDTA-EN/STND/TRANS MS #268, 6501 E. 11 Mile Road, Warren, MI 48397-5000.) 2.3 Non-Government publications. The following documents form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these docum

14、ents are those cited in the solicitation or contract (see 6.2). AMERICAN SOCIETY FOR QUALITY (ASQ) ANSI/ASQ Z1.4 - Sampling Procedures and Tables for Inspection by Attributes (DoD Adopted) (Copies of this document are available from www.asq.org or American Society for Quality, 600 North Plankinton A

15、venue, Milwaukee, WI 53203.) GENERAL MOTORS CORPORATION GM 9540P - Accelerated Corrosion Test (Copies of this document are available from General Motors North America, c/o Global Engineering Documents, 15 Inverness Way East, Englewood, CO 80112 or .) THE EUROPEAN TYRE AND RIM TECHNICAL ORGANISATION

16、(ETRTO) Standards Manual (Copies of this document are available from www.etrto.org or The European Tyre and Rim Technical Organisation, Av. Brugmann, 32/2, B-1060 Brussels, Belgium.) THE TIRE AND RIM ASSOCIATION, INC. Year Book (Copies of this document are available from www.us-tra.org or The Tire a

17、nd Rim Association, Inc., 175 Montrose West Avenue, Suite 150, Copley, OH 44321.) 2.4 Order of precedence. Unless otherwise noted herein or in the contract, in the event of a conflict between the text of this document and the references cited herein, the text of this document takes precedence. Nothi

18、ng in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-45322J 4 3. REQUIREMENTS 3.1 First article. When specified (see 6.2), a sa

19、mple shall be subjected to first article inspection in accordance with 4.2. 3.2 Materials. Materials used shall be in accordance with the manufacturers materials specifications for dollies. The materials shall be capable of meeting all the operational and environmental requirements specified herein.

20、 Recovered materials shall be used to the maximum extent practicable (see 4.5.1). 3.2.1 Ozone resistance. When rubber components are required to be ozone resistant, the degree of resistance shall be as specified in applicable specifications or drawings (see 4.5.1 and 6.2). 3.3 Construction. The vehi

21、cle shall be constructed in accordance with the applicable drawings specified in table I and as supplemented herein. The vehicle shall be complete with all specified items installed, including reflectors, payload tiedowns, lashing hooks, lifting devices, and tools (see 4.5.2). TABLE I. Drawings. Mod

22、el Drawing M197A1 8736120 M198A1 8736124 M354 8736308 3.3.1 Seals. When fording or operating in mud, sand or snow, seals shall prevent entrance of foreign matter into the bearings. Bearing seals shall restrict the leaking of lubricants from bearing (see 4.5.3). 3.3.2 Electrical circuits. Electrical

23、circuits shall maintain continuity from end to end, without evidence of internal or external shorts, during all vehicle operating conditions (see 4.5.2 and 4.5.4). 3.3.3 Controls. All electrical, mechanical, and hydraulic controls shall operate without malfunction under all vehicle operating conditi

24、ons (see 4.5.2 and 4.5.5). 3.3.4 Adjustment mechanisms. All adjustment mechanisms shall function properly, and maintain adjustment within required settings during all vehicle operating conditions (see 4.5.2 and 4.5.6). 3.3.5 Welding and rivets. Welding and rivets shall meet the quality requirements

25、specified on the applicable drawing (see 4.5.2). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-45322J 5 3.3.5.1 Welding repairs. Welding repairs of any kind shall be made only when, and to the extent, specifically authorized by the procurin

26、g activity (see 4.5.2 and 6.2). 3.3.6 Tires and tubes. 3.3.6.1 Tires. Tires shall be cross-country type as specified for tactical vehicles. Tires shall be in accordance with the Tire and Rim Association or to the European Tyre and Rim Technical Organization recommendations. Size of tires shall be as

27、 specified in the applicable vehicle characteristic data sheets (see 4.5.1, 4.5.2 and 6.4). 3.3.6.2 Inner tubes. When tube type tires are specified, inner tubes shall be of heavy duty type and shall be of proper size for tires furnished. Tube type radial tires shall have radial type inner tubes. Tir

28、e flaps shall be provided for tube type tires in accordance with the Tire and Rim Association recommendations. 3.3.7 Intervehicular connections. Safety chains, cables, and hoses shall be of sufficient length and routed correctly to function properly under any vehicular orientation (see 4.5.2). 3.3.7

29、.1 Drawbar assembly. Drawbar shall raise and lower correctly to allow vehicular connection (see 4.5.2). 3.3.8 Suspension. Suspension clearances shall prevent interference between wheels and other portions of the vehicle when vehicle is in use under any condition of its intended purpose (see 4.5.2 an

30、d 4.5.7). 3.3.9 Axle assembly. The axle assembly shall be properly installed and shall have a capacity as specified in table IV for the applicable vehicle (see 4.5.2). 3.3.10 Fifth wheel. The fifth wheel shall accommodate the applicable semitrailer kingpin and meet the performance requirements of th

31、e 6000 mile operational test (see 4.5.2 and 4.5.7). 3.3.11 Lunette. Lunette shall accommodate the applicable towing vehicle attachment device at maximum gross vehicle weight (GVW) of the trailer (see 4.5.2). 3.4 Performance. The vehicle shall meet the performance requirements of this specification w

32、hen fully equipped, loaded with rated payload, serviced with standard products (see 6.5) and towed by appropriate military towing vehicle. 3.4.1 Reliability. Vehicles with rated payload, when operated in accordance with 4.5.7, shall possess not less than 60 percent probability of completing not less

33、 than 6000 miles without replacement or overhaul of the principal components and/or subassemblies. 3.4.2 Maintainability. The total scheduled maintenance, excluding driver/crew checks and services, shall be between 4 and 8 man hours. The total unscheduled maintenance shall be Provided by IHSNot for

34、ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-45322J 6 between 0 and 12 manhours during the first 6000 miles of operation (see 4.5.7). This equates to a Maintenance Ratio (MR) of 0.013 to 0.067 at 20 miles per hours (mph) and a MR of 0.02 to 0.10 at 30 mph. The s

35、cheduled maintenance intervals shall be 3 months or 3000 miles of operation, whichever comes first. Maximum time to repair (only to include diagnosis, repair and verification) shall be as follows, using personnel normally employed: a. Organization maintenance shall not exceed 3 manhours 95% of the t

36、ime. b. Direct support maintenance shall not exceed 10 manhours 95% of the time. c. General support maintenance - not required. 3.4.3 Environmental. The vehicle shall operate as specified herein, under extreme conditions of weather, in ambient air temperatures ranging from -50 degrees Fahrenheit (F)

37、 to +125 F (see 4.5.8). 3.4.4 Service products. Servicing and lubrication shall be performed using standard service products (see 4.5.1 and 6.5). 3.4.5 Highway and cross-country operations. 3.4.5.1 Highway operation. When loaded and towed at specified speeds, in a straight line, on a relatively leve

38、l, smooth paved surface, the path of the towed vehicle shall not deviate more than 3 inches to either side of the path of the towing vehicle (see 4.5.9). 3.4.5.2 Cross-country operation. The vehicle shall be towable at specified load and speed over unimproved roads, or gently rolling terrain. When s

39、o operated in a straight line, the vehicle shall track the towing vehicle without damage to itself or the towing vehicle. Stability shall be maintained (see 4.5.10). 3.4.6 Gradeability. When towed over a dry, hard-surfaced road, free of loose material, each vehicle shall exhibit the stability and gr

40、adeability specified. 3.4.6.1 Longitudinal inclines. Each vehicle shall follow the towing vehicle, without weaving to an extent which adversely affects the controllability of the vehicle combination, when ascending or descending longitudinal inclines having a 15% grade (see 4.5.11). 3.4.6.2 Side slo

41、pes. Each vehicle shall follow the towing vehicle without slipping or upsetting when operating, either left or right, on 20% side slopes (see 4.5.12). 3.4.7 Turning ability. When coupled to the towing vehicle, operating in its minimum turning circle, each vehicle shall follow without cramping or sid

42、e-slipping and without damage to or interference between the towed vehicle and the towing vehicle (see 4.5.13). 3.4.8 Braking ability. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-45322J 7 3.4.8.1 Service brakes. The combined service brake

43、s of the vehicle and towing vehicle shall control, decelerate, and stop the vehicle combination within 30 feet from a speed of 20 mph on dry, hard, level, smooth surfaced roads. Hydraulic brakes shall conform to FMVSS No. 105 (see 4.5.2 and 4.5.14). 3.4.8.2 Automatic actuation. The automatic breakaw

44、ay device shall apply and maintain application of the vehicle brakes for not less than 15 minutes, upon breakaway from the towing vehicle (see 4.5.2 and 4.5.15). 3.4.9 Fording. Each vehicle shall ford hard-bottomed, salt or fresh water crossings of depths great enough to completely submerge the chas

45、sis to top of fifth wheel and shall withstand such submergence for periods up to 15 minutes duration without damage to the vehicle or its components (see 4.5.16). 3.4.10 Landing leg. Unless otherwise specified (see 6.2), the vehicle shall have a landing leg. The landing leg shall exhibit capacity an

46、d adjustment to raise, support and hold its portion of the fully loaded vehicle and shall withstand, without damage, the strains imposed when coupling or uncoupling the towing vehicle. The landing leg shall extend and retract; and when retracted, shall provide ground clearance for cross-country oper

47、ation (see 4.5.2 and 4.5.17). 3.5 Surface treatment. Unless otherwise specified (see 6.2), exterior surfaces of the vehicle shall be cleaned, treated, primed, and painted in accordance with the manufacturers standard practice. The color of the exterior paint coat shall be as specified in the contrac

48、t (see 6.2). When specified (see 6.2), Chemical Agent Resistant Coatings (CARC) paint shall be required (see 4.5.2). 3.5.1 Corrosion protection. The dollies shall function as intended and shall show no signs of detrimental corrosion after being subjected to a salt spray solution (see 4.5.2 and 4.5.8

49、.1). 3.6 Marking. The identification marking and data plates shall be permanent and legible and shall include, as a minimum (see 4.5.2, 6.2 and 6.3): a. Part or identification number (PIN). b. Model number. c. Manufacturers name or trademark. d. Date of manufacture. e. Contract or order number. 3.6.1 Identification plates. Identification plates shall meet the requirements of A-A-50271 (see 4.5.2). 3.7 S