ARMY MIL-DTL-3943 148 D-2010 DECORATION COMMENDATION MEDAL FEDERAL BUREAU OF PRISONS DEPARTMENT OF JUSTICE《奖章 司法部联邦监狱管理局嘉奖奖章》.pdf

《ARMY MIL-DTL-3943 148 D-2010 DECORATION COMMENDATION MEDAL FEDERAL BUREAU OF PRISONS DEPARTMENT OF JUSTICE《奖章 司法部联邦监狱管理局嘉奖奖章》.pdf》由会员分享，可在线阅读，更多相关《ARMY MIL-DTL-3943 148 D-2010 DECORATION COMMENDATION MEDAL FEDERAL BUREAU OF PRISONS DEPARTMENT OF JUSTICE《奖章 司法部联邦监狱管理局嘉奖奖章》.pdf（2页珍藏版）》请在麦多课文档分享上搜索。

1、AMSC N/A Page 1 of 2 FSC 8455 DETAIL SPECIFICATION SHEET DECORATION, COMMENDATION MEDAL, FEDERAL BUREAU OF PRISONS, DEPARTMENT OF JUSTICE This specification is approved for use by all Departments and Agencies of the Department of Defense. The requirements for acquiring the product described herein s

2、hall consist of this specification sheet and the latest issue of MIL-DTL-3943. OBVERSE REVERSE DASH NO. -1: Regular Size -2: Miniature Size MATERIAL: Red Brass FINISH: Brass, Oxidized, Buffed Relieved and shall match The Institute of Heraldry (TIOH) Metal Finish Chip Number 4. DIMENSIONS: HEIGHT (in

3、cluding lug): -1: 1-1/2 inches (REF) -2: 27/32 inch (REF) INCH-POUND MIL-DTL-3943/148D 15 January 2010 SUPERSEDING MIL-DTL-3943/148C 26 September 2001 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-3943/148D Page 2 of 2 WIDTH (overall): -1:

4、1-3/8 inches (REF) -2: 11/16 inch (REF) THICKNESS (at edge): -1: 0.150 inch 0.010 inch -2: 0.100 inch 0.010 inch NOTES: 1. The term (REF) refers to the measurements taken from the Government furnished hub or die. 2. The pendant drape for the regular size (-1) civilian medal shall be a neck ribbon fa

5、bricated as illustrated by the figure in MIL-DTL-3943 titled “Neck ribbon, Legion of Merit, Commander.“ The pendant shall be attached to the neck ribbon using two jump rings. A jump ring fabricated from 0.050 inch diameter wire having an outside diameter of 3/8 inch shall be attached to the pendant.

6、 A neck ribbon ring fabricated from 0.050 inch diameter wire having an outside diameter of 1/2 inch shall be attached to the pendant jump ring. The neck ribbon shall be placed through the neck ribbon ring. The ends of the jump rings shall be square cut, in line, and together. 3. Decoration set for m

7、ilitary personnel shall consist of a regular size medal, a miniature size medal, a service ribbon, and a lapel button, all packaged in a presentation case conforming to MIL-C-14633, Type XVI with Type XVI, Class 2 or 4 pad. 4. Decoration set for civilians shall consist of a regular size medal with a

8、 neck ribbon, a miniature size medal, and a lapel button, all packaged in a presentation case conforming to MIL-C-14633, Type XVI with Type XVI, Class 2 or 4 pad. 5. The ribbon for the pendant drape and service ribbon shall conform to MIL-DTL-11589/375. 6. The lapel button for military personnel sha

9、ll conform to MIL-DTL-11484/194. 7. The lapel button for civilians shall conform to MIL-DTL-11484/197. CHANGES FROM PREVIOUS ISSUE: Marginal notations are not used in this revision to identify changes with respect to the previous issue due to the extent of the changes. Custodians: Preparing activity

10、: Army - IH Army - IH Review activities: (Project No. 8455-2010-052) DLA - CT NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at http:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-