ARMY MIL-DTL-3628 39 G-2009 BADGE QUALIFICATION MARINE CORPS PISTOL CHAMPIONSHIP (WALSH TROPHY)《海军陆战队手枪射击冠军(WALSH 奖)资质徽章》.pdf

《ARMY MIL-DTL-3628 39 G-2009 BADGE QUALIFICATION MARINE CORPS PISTOL CHAMPIONSHIP (WALSH TROPHY)《海军陆战队手枪射击冠军(WALSH 奖)资质徽章》.pdf》由会员分享，可在线阅读，更多相关《ARMY MIL-DTL-3628 39 G-2009 BADGE QUALIFICATION MARINE CORPS PISTOL CHAMPIONSHIP (WALSH TROPHY)《海军陆战队手枪射击冠军(WALSH 奖)资质徽章》.pdf（2页珍藏版）》请在麦多课文档分享上搜索。

1、AMSC N/A Page 1 of 2 FSC 8455 INCH-POUND MIL-DTL-3628/39G 15 August 2009 SUPERSEDING MIL-DTL-3628/39F 15 November 1996 DETAIL SPECIFICATION SHEET BADGE, QUALIFICATION, MARINE CORPS PISTOL CHAMPIONSHIP (WALSH TROPHY) This specification is approved for use by all Departments and Agencies of the Depart

2、ment of Defense. The requirements for acquiring the product described herein shall consist of this specification sheet and the latest issue of MIL-DTL-3628. MATERIAL: Red Brass FINISH (Pendant and Suspension Bar): OBVERSE: Gold Plated, Polished Highlights and shall match The Institute of Heraldry Me

3、tal Finish Chip Number 8. REVERSE: Gold Plated, Mirror-like Polished and shall match TIOH Metal Finish Chip Number 6. DIMENSIONS: HEIGHT (overall): ASSEMBLED: 2 inches (REF) PENDANT (excluding lugs): 1-15/32 inches (REF) SUSPENSION BAR (excluding lugs): 9/32 inch (REF) Provided by IHSNot for ResaleN

4、o reproduction or networking permitted without license from IHS-,-,-MIL-DTL-3628/39G Page 2 of 2 WIDTH (overall): PENDANT: 1-15/64 inches (REF) SUSPENSION BAR (including balls): 1-17/32 inches (REF) THICKNESS: PENDANT (at thickest point): 0.115 inch + .005 inch SUSPENSION BAR (at rim): 0.070 inch +

5、.005 inch NOTES: 1. The term (REF) refers to the measurements taken from the Government furnished hub or die. 2. The links shall be oblong shaped, 7/32 inch + 1/32 long by 5/32 inch + 1/32 inch wide and shall be formed from 0.040 inch + 0.002 inch diameter wire. 3. The lugs are an integral part of b

6、oth the pendant and the suspension bar. 4. The attaching device shall be prong and flat ball clutch type. The prongs shall be located on the horizontal center line of the back of the suspension bar equidistant from each end and 1-1/32 inch + 1/32 inch apart. CHANGES FROM PREVIOUS ISSUE: The margins

7、of this specification are marked with vertical lines to indicate where changes from the previous issue were made. This was done as a convenience only and the Government assumes no liability whatsoever for any inaccuracies in these notations. Bidders and contractors are cautioned to evaluate the requ

8、irements of this document based on the entire content irrespective of the marginal notations and relationship to the last previous issue. Custodian: Preparing activity: Army - IH Army - IH Navy MC (Project No. 8455-2009-099) Review activities: DLA - CT NOTE: The activities listed above were interest

9、ed in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at http:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-