ARMY MIL-DTL-3628 36 F-2013 BADGE QUALIFICATION DISTINGUISHED PISTOL SHOT USMC.pdf

《ARMY MIL-DTL-3628 36 F-2013 BADGE QUALIFICATION DISTINGUISHED PISTOL SHOT USMC.pdf》由会员分享，可在线阅读，更多相关《ARMY MIL-DTL-3628 36 F-2013 BADGE QUALIFICATION DISTINGUISHED PISTOL SHOT USMC.pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、 AMSC N/A Page 1 of 3 FSC 8455 DETAIL SPECIFICATION SHEET BADGE, QUALIFICATION, DISTINGUISHED PISTOL SHOT, USMC This specification is approved for use by all Departments and Agencies of the Department of Defense The requirements for acquiring the product described herein shall consist of this specif

2、ication sheet and the latest issue of MIL-DTL-3628. MATERIAL: PENDANT: Gilding Metal SUSPENSION BAR: Red Brass 85/15 (UNS Alloy No. C-230) or Gilding Metal FINISH: PENDANT: OBVERSE: Hard Epoxy, 24K Gold Plated, Matte Finish, Polished Highlights and shall match The Institute of Heraldry (TIOH) Metal

3、Finish Chip Number 8. REVERSE: 24K Gold Plated, Mirror-Like Polished and shall match TIOH Metal Finish Chip Number 6. INCH-POUND MIL-DTL-3628/36F 08 January 2013 SUPERSEDING MIL-DTL-3628/36E 15 November 1996 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IH

4、S-,-,-MIL-DTL-3628/36F Page 2 of 3 SUSPENSION BAR: OBVERSE: 24K Gold Plated, Matte Finish, Polished Highlights and shall match TIOH Metal Finish Chip Number 8. REVERSE: 24K Gold Plated, Mirror-Like Polished and shall match TIOH Metal Finish Chip Number 6. DIMENSIONS: HEIGHT (Overall): PENDANT: 1-17/

5、64 inches (REF) SUSPENSION BAR: 9/32 inch (REF) WIDTH (Overall): PENDANT: 1-1/16 inches (REF) SUSPENSION BAR: 1-1/2 inches (REF) THICKNESS: (At rim): PENDANT: 0.062 inch + 0.010 inch SUSPENSION BAR: 0.062 inch + 0.010 inch EPOXY: Hard epoxy resin shall be applied as indicated below, and shall match

6、TIOH Hard Enamel Color Chip Number listed: TIOH HARD ENAMEL COLOR CHIP NUMBER LOCATION Black #26 See Picture White #28 See Picture ATTACHING DEVICE AND LUGS: 1. Links shall be 13/64 inch + 1/64 inch in width and 1/4 inch + 1/64 inch in length and shall be fabricated from 0.044 inch + 0.005 inch diam

7、eter wire. 2. The attaching device shall be prong and Flat ball clutch type. 3. The prongs and clutch shall be located on the horizontal center line on the back of the suspension bar equidistant from each end and 1- 1/4 inch + 1/32 inch apart. 4. Lugs are integral NOTES: The term (REF) refers to the

8、 measurements taken from the Government furnished hub or die. CHANGES FROM PREVIOUS ISSUE: Marginal notations are not used in this revision to identify changes with respect to the previous issue due to the extent of the changes. Provided by IHSNot for ResaleNo reproduction or networking permitted wi

9、thout license from IHS-,-,-MIL-DTL-3628/36F Page 3 of 3 Custodians: Preparing activity: Army - IH Army - IH Navy - MC Review activity: (Project No. 8455-2013-046) DLA - CT NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-