ARMY MIL-DTL-3628 24 J-2009 BADGE QUALIFICATION COMBAT INFANTRYMAN ARMY《陆军战斗步兵资质徽章》.pdf

《ARMY MIL-DTL-3628 24 J-2009 BADGE QUALIFICATION COMBAT INFANTRYMAN ARMY《陆军战斗步兵资质徽章》.pdf》由会员分享，可在线阅读，更多相关《ARMY MIL-DTL-3628 24 J-2009 BADGE QUALIFICATION COMBAT INFANTRYMAN ARMY《陆军战斗步兵资质徽章》.pdf（4页珍藏版）》请在麦多课文档分享上搜索。

1、 AMSC N/A Page 1 of 4 FSC 8455 INCH-POUND MIL-DTL-3628/24J 15 August 2009 SUPERSEDING MIL-DTL-3628/24H 15 November 1996 DETAIL SPECIFICATION SHEET BADGE, QUALIFICATION, COMBAT INFANTRYMAN, ARMY This specification is approved for use by all Departments and Agencies of the Department of Defense. The r

2、equirements for acquiring the product described herein shall consist of this specification sheet and the latest issue of MIL-DTL-3628. MATERIAL: Red Brass or Nickel Silver FINISH: -1 thru -4, -9 thru -12, -17 thru -20: FRAME - Soft Enameled, Nickel Plated (Red Brass only), Silver Plated, Oxidized, R

3、elieved, Matte Finish and shall match The Institute of Heraldry (TIOH) Metal Finish Chip Number 14. STAR(S) - Silver Plated, Mirror-like Polished (when applicable). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-3628/24J Page 2 of 4 -5 thru

4、-8, -13 thru 16: WREATH - Shaded, Gold Plated, Matte Finish and shall match TIOH Metal Finish Chip Number 7. STAR(S) (When applicable) - Gold Plated, Mirror-like Polished and shall match TIOH Metal Finish Chip Number 6. FRAME - Soft Enameled, Gold Plated, Matte Finish and shall match TIOH Metal Fini

5、sh Chip Number 7. -21,-22,-23,-24: Dull, Flat Black Enamel Finish. DASH NO. -1: 1st Award, Silver, Regular Size -2: 2nd Award, Silver, Regular Size -3: 3rd Award, Silver, Regular Size -4: 4th Award, Silver, Regular Size -5: 5th Award, Gold, Regular Size -6: 6th Award, Gold, Regular Size -7: 7th Awar

6、d, Gold, Regular Size -8: 8th Award, Gold, Regular Size -9: 1st Award, Silver, Miniature Size -10: 2nd Award, Silver, Miniature Size -11: 3rd Award, Silver, Miniature Size -12: 4th Award, Silver, Miniature Size -13: 5th Award, Gold, Miniature Size -14: 6th Award, Gold, Miniature Size -15: 7th Award,

7、 Gold, Miniature Size -16: 8th Award, Gold, Miniature Size -17: 1st Award, Silver, Dress Miniature -18: 2nd Award, Silver, Dress Miniature -19: 3rd Award, Silver, Dress Miniature -20: 4th Award, Silver, Dress Miniature -21: 1st Award, Subdued, Regular Size -22: 2nd Award, Subdued, Regular Size -23:

8、3rd Award, Subdued, Regular Size -24: 4th Award, Subdued, Regular Size DIMENSIONS: HEIGHT (overall): -1,-5,-21: 1 inch (REF) -2,-3,-6,-7,-22,-23: 1-3/16 inch (REF) -4,-8,-24: 1-5/16 inch (REF) -9,-13: 13/16 inch (REF) -10,-11,-14,-15: 61/64 inch (REF) -12,-16: 1-1/64 inch (REF) -17: 7/16 inch (REF)

9、-18,-19: 1/2 inch (REF) -20: 9/16 inch (REF) Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-3628/24J Page 3 of 4 WIDTH: (overall): -1 thru -8, -21 thru -24: 3 inches (REF) -9 thru -16: 1-3/4 inch (REF) -17 thru -20: 1-1/4 inch (REF) THICKNES

10、S (at edge): 0.060 inch + 0.005 inch NOTES: 1. The term (REF) refers to the measurements taken from the Government furnished hub or die. 2. Piercing shall be as indicated. 3. Enameled areas shall be light blue soft enamel and shall conform to TIOH Color Chip No. 30 or the standard sample. 4. Epoxy r

11、esin (stoning epoxy) may be used in lieu of soft enamel at the option of the manufacturer. Epoxy resin shall be smooth and flush with the bottom of the rifle. The epoxy need not be stoned. 5. The dull, flat black enamel for Dash No. -21 through -24 shall match FED-STD-595, Chip Number 37038. 6. The

12、attaching device shall be prong and clutch type. Prongs shall be located on the horizontal center line and equidistant from each end. For regular size, the prongs shall be 2 inches + 1/64 inch apart. For miniature size and dress miniatures, the prongs shall be 1 inch + 1/64 inch apart. 7. A forcer m

13、ay be used to bring up the musket only. 8. Pierced areas for the dress miniatures shall be as indicated below: -17: As indicated. -18: As indicated except no piercing under star. -19: Between the two stars only (center area). -20: Between the three stars only (center area). 9. Silver colored badges

14、may be nickel or rhodium plated with a mirror-like polished finish for commercial sale and shall match TIOH Metal Finish Chip Number 16. The silver plating requirement shall not apply for nickel or rhodium plated insignia. Provided by IHSNot for ResaleNo reproduction or networking permitted without

15、license from IHS-,-,-MIL-DTL-3628/24J Page 4 of 4 CHANGES FROM PREVIOUS ISSUE: The margins of this specification are marked with vertical lines to indicate where changes from the previous issue were made. This was done as a convenience only and the Government assumes no liability whatsoever for any

16、inaccuracies in these notations. Bidders and contractors are cautioned to evaluate the requirements of this document based on the entire content irrespective of the marginal notations and relationship to the last previous issue. Custodian: Preparing activity: Army - IH Army - IH (Project No. 8455-20

17、09-090) Review activities DLA - CT NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at http:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-