ARMY MIL-DTL-3628 156 B-2012 BADGE IDENTIFICATION ARMY STAFF ARMY.pdf

《ARMY MIL-DTL-3628 156 B-2012 BADGE IDENTIFICATION ARMY STAFF ARMY.pdf》由会员分享，可在线阅读，更多相关《ARMY MIL-DTL-3628 156 B-2012 BADGE IDENTIFICATION ARMY STAFF ARMY.pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、AMSC N/A Page 1 of 2 FSC 8455 DETAIL SPECIFICATION SHEET BADGE, IDENTIFICATION, ARMY STAFF ARMY This specification is approved for use by all Departments and Agencies of the Department of Defense. The requirements for acquiring the product described herein shall consist of this specification sheet a

2、nd the latest issue of MIL-DTL-3628. Black Enamel Pierced (-1 and -2) Pierced ( -1 Only) Pierced (-1, -2 and -3) White Enamel Blue Enamel Green Enamel Red Enamel DASH NO. -1: Chief of Staff -2: Army Staff Regular Size -3: Army Staff Miniature Size MATERIAL: Gilding Metal 95/5 (UNS Alloy NO. C-210) I

3、NCH-POUND MIL-DTL-3628/156B 10 December 2012 SUPERSEDING MIL-DTL-3628/156A 1 June 1998 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-3628/156B Page 2 of 3 FINISH: OBVERSE: Hard Expoxy, 24K, Gold Plated, Mirror-Like Polished and shall match

4、The Institute of Heraldry (TIOH) Metal Finish Chip Number 6. REVERSE: 24K Gold Plated, Mirror-Like Polished and shall match TIOH Metal Finish Chip Number 6. DIMENSIONS: STAR: CRCUMSCRIBED DIAMETER: -1: 3 inches (REF) -2: 2 inches (REF) -3: 1-1/2 inches (REF) THICKNESS: 0.060 inch + 0.005 inch DEVICE

5、: HEIGHT (Overall): -1: 1-5/8 inches (REF) -2: 1-1/16 inches (REF) -3: 13/16 inch (REF) THICKNESS: 0.050 inch + 0.005 inch ASSEMBLED THICKNESS (Chief of shield): 0 .110 inch + 0.005 inch. EPOXY: Hard epoxy enamel shall be applied as indicated below, and shall match TIOH Hard Enamel Color Chip Number

6、 listed: TIOH HARD ENAMEL COLOR CHIP NUMBER Black 26 White 28 Green 11 Red 1 Blue 20 ATTACHING DEVICE AND SHIELD: 1. The Shield for -1 and -2 has 13 stripes. 2. The shield for -3 has 7 stripes 3. The stripes of both shields shall be enamel with alternating white and red; beginning with white and end

7、ing with white. 4. -1 shall be spherically dapped to radius of 2-1/2 inches + 1/4 inch - 0 when measured on the reverse. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-3628/156B Page 3 of 3 5. -2 shall be spherically dapped to radius of 2 in

8、ches + 1/8 inch when measured on the reverse. 6. -3 shall be spherically dapped to radius of 1-1/2 inches + 1/16 inch when measured on the reverse. 7. The device shall be secured to the background by two solid brass rivets and shall be dapped to insure a snug fit. The device shall be pierced as show

9、n. 8. The attaching device shall be three prongs and clutches. The prongs shall be located 3/16 inch + 1/32 inch in from the edge of the badge. One prong shall be at the top and centered on the vertical center line and the other prongs shall be located on either side of the badge on the first leaf b

10、elow the horizontal center line. 9. As an alternate method of manufacturing for commercial sale only, 22 K Gold Plated, Mirror like Polished may used which shall match TIOH Metal Finish Chip Number 9. NOTES: The term (REF) refers to the measurements taken from the Government furnished hub or die. CH

11、ANGES FROM PREVIOUS ISSUE: Marginal notations are not used in this revision to identify changes with respect to the previous issue due to the extent of the changes. Custodian: Preparing activity: Army - IH Army - IH Review activity: (Project No. 8455-2013-047) DLA - CT NOTE: The activities listed ab

12、ove were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-