ARMY MIL-DTL-3628 155 B-2009 BADGE IDENTIFICATION HONOR GUARD TOMB OF THE UNKNOWN SOLDIER ARMY《徽章 陆军无名战士纪念碑仪仗队的识别徽章》.pdf

《ARMY MIL-DTL-3628 155 B-2009 BADGE IDENTIFICATION HONOR GUARD TOMB OF THE UNKNOWN SOLDIER ARMY《徽章 陆军无名战士纪念碑仪仗队的识别徽章》.pdf》由会员分享，可在线阅读，更多相关《ARMY MIL-DTL-3628 155 B-2009 BADGE IDENTIFICATION HONOR GUARD TOMB OF THE UNKNOWN SOLDIER ARMY《徽章 陆军无名战士纪念碑仪仗队的识别徽章》.pdf（2页珍藏版）》请在麦多课文档分享上搜索。

1、AMSC N/A Page 1 of 2 FSC 8455 INCH-POUND MIL-DTL-3628/155B 1 August 2009 SUPERSEDING MIL-DTL-3628/155A 3 April 2006 DETAIL SPECIFICATION SHEET BADGE, IDENTIFICATION, HONOR GUARD, TOMB OF THE UNKNOWN SOLDIER, ARMY This specification is approved for use by all Departments and Agencies of the Departmen

2、t of Defense. The requirements for acquiring the product described herein shall consist of this specification sheet and the latest issue of MIL-DTL-3628. DASH NO. -1: Regular Size -2: Regular Size, Subdued MATERIAL: Red Brass or Nickel Silver FINISH: -1: Nickel Plated, (Red Brass Only), Silver Plate

3、d, Oxidized, Relieved, Matte Finish, Polished Highlights on Leaves and lettering and shall match The Institute of Heraldry (TIOH) Metal Finish Chip Number 15. Reverse shall be bright and clean. -2: Dull, Flat Black Enamel and shall match TIOH Metal Finish Chip Number 21. Provided by IHSNot for Resal

4、eNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-3628/155B Page 2 of 2 DIMENSIONS: HEIGHT -1, -2: (Overall): 1-15/32 inches (REF) WIDTH (Overall): -1, -2: 2 inches (REF) THICKNESS (At Edge): -1, -2: 0.065 inch + 0.010 inch NOTES: 1. The term (REF) refers to the measureme

5、nts taken from the Government furnished hub or die. 2. The attaching device shall be prong and clutch type. One prong shall be located on the center of each wreath 1 inch + 1/32 inch from the bottom of the badge. One prong shall be located on the vertical center line 1/4 inch + 1/32 inch from the to

6、p of the badge. 3. A forcer may be used to bring up the replica of the tomb only. CHANGES FROM PREVIOUS ISSUE: The margins of this specification are marked with vertical lines to indicate where changes from the previous issue were made. This was done as a convenience only and the Government assumes

7、no liability whatsoever for any inaccuracies in these notations. Bidders and contractors are cautioned to evaluate the requirements of this document based on the entire content irrespective of the marginal notations and relationship to the last previous issue. Custodian: Preparing activity: Army - I

8、H Army - IH (Project No. 8455-2009-108) Review activities: DLA - CT NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at http:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-